[ 0.000000] Linux version 5.15.78-yocto-standard (oe-user@oe-host) (mips64-poky-linux-gcc (GCC) 11.3.0, GNU ld (GNU Binutils) 2.38.20220708) #1 SMP PREEMPT Wed Nov 16 14:15:49 UTC 2022 [ 0.000000] earlycon: uart8250 at I/O port 0x3f8 (options '38400n8') [ 0.000000] printk: bootconsole [uart8250] enabled [ 0.000000] CPU0 revision is: 00010000 (MIPS GENERIC QEMU) [ 0.000000] FPU revision is: 007f0000 [ 0.000000] OF: fdt: No chosen node found, continuing without [ 0.000000] MIPS: machine is mti,malta [ 0.000000] Software DMA cache coherency enabled [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000000000000-0x0000000000ffffff] [ 0.000000] DMA32 [mem 0x0000000001000000-0x00000000ffffffff] [ 0.000000] Normal empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000] node 0: [mem 0x0000000090000000-0x000000009fffefff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000009fffefff] [ 0.000000] percpu: Embedded 24 pages/cpu s61216 r8192 d28896 u98304 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 120831 [ 0.000000] Kernel command line: root=/dev/vda rw ip=192.168.7.8::192.168.7.7:255.255.255.0::eth0:off:8.8.8.8 console=ttyS0 console=ttyS1 console=ttyS0 console=tty printk.time=1 [ 0.000000] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes, linear) [ 0.000000] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 463204K/524284K available (12644K kernel code, 1900K rwdata, 2860K rodata, 432K init, 350K bss, 61080K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] trace event string verifier disabled [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. [ 0.000000] Trampoline variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 [ 0.000000] NR_IRQS: 256 [ 0.000000] CPU frequency 333.34 MHz [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467385209 ns [ 0.000128] sched_clock: 32 bits at 166MHz, resolution 5ns, wraps every 12884702205ns [ 0.012568] Console: colour dummy device 80x25 [ 0.013192] printk: console [tty0] enabled [ 0.013990] printk: bootconsole [uart8250] disabled [ 0.000000] Linux version 5.15.78-yocto-standard (oe-user@oe-host) (mips64-poky-linux-gcc (GCC) 11.3.0, GNU ld (GNU Binutils) 2.38.20220708) #1 SMP PREEMPT Wed Nov 16 14:15:49 UTC 2022 [ 0.000000] earlycon: uart8250 at I/O port 0x3f8 (options '38400n8') [ 0.000000] printk: bootconsole [uart8250] enabled [ 0.000000] CPU0 revision is: 00010000 (MIPS GENERIC QEMU) [ 0.000000] FPU revision is: 007f0000 [ 0.000000] OF: fdt: No chosen node found, continuing without [ 0.000000] MIPS: machine is mti,malta [ 0.000000] Software DMA cache coherency enabled [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000000000000-0x0000000000ffffff] [ 0.000000] DMA32 [mem 0x0000000001000000-0x00000000ffffffff] [ 0.000000] Normal empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000] node 0: [mem 0x0000000090000000-0x000000009fffefff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000009fffefff] [ 0.000000] percpu: Embedded 24 pages/cpu s61216 r8192 d28896 u98304 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 120831 [ 0.000000] Kernel command line: root=/dev/vda rw ip=192.168.7.8::192.168.7.7:255.255.255.0::eth0:off:8.8.8.8 console=ttyS0 console=ttyS1 console=ttyS0 console=tty printk.time=1 [ 0.000000] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes, linear) [ 0.000000] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 463204K/524284K available (12644K kernel code, 1900K rwdata, 2860K rodata, 432K init, 350K bss, 61080K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] trace event string verifier disabled [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. [ 0.000000] Trampoline variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 [ 0.000000] NR_IRQS: 256 [ 0.000000] CPU frequency 333.34 MHz [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467385209 ns [ 0.000128] sched_clock: 32 bits at 166MHz, resolution 5ns, wraps every 12884702205ns [ 0.012568] Console: colour dummy device 80x25 [ 0.013192] printk: console [tty0] enabled [ 0.013990] printk: bootconsole [uart8250] disabled [ 0.016113] Calibrating delay loop... 812.64 BogoMIPS (lpj=4063232) [ 0.112028] pid_max: default: 32768 minimum: 301 [ 0.113182] LSM: Security Framework initializing [ 0.114521] landlock: Up and running. [ 0.117229] Mount-cache hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.117400] Mountpoint-cache hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.161275] Performance counters: Either hardware does not support performance counters, or not yet implemented. [ 0.162753] rcu: Hierarchical SRCU implementation. [ 0.170486] smp: Bringing up secondary CPUs ... [ 0.170654] smp: Brought up 1 node, 1 CPU [ 0.186738] devtmpfs: initialized [ 0.195876] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.196149] futex hash table entries: 256 (order: 2, 16384 bytes, linear) [ 0.207576] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.471916] raid6: int64x8 gen() 375 MB/s [ 0.649720] raid6: int64x8 xor() 304 MB/s [ 0.820803] raid6: int64x4 gen() 829 MB/s [ 0.998935] raid6: int64x4 xor() 444 MB/s [ 1.178301] raid6: int64x2 gen() 1081 MB/s [ 1.348541] raid6: int64x2 xor() 573 MB/s [ 1.528204] raid6: int64x1 gen() 825 MB/s [ 1.707423] raid6: int64x1 xor() 492 MB/s [ 1.707584] raid6: using algorithm int64x2 gen() 1081 MB/s [ 1.707673] raid6: .... xor() 573 MB/s, rmw enabled [ 1.707835] raid6: using intx1 recovery algorithm [ 1.714799] vgaarb: loaded [ 1.716505] SCSI subsystem initialized [ 1.717270] usbcore: registered new interface driver usbfs [ 1.717789] usbcore: registered new interface driver hub [ 1.718076] usbcore: registered new device driver usb [ 1.718574] pps_core: LinuxPPS API ver. 1 registered [ 1.718651] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 1.718858] PTP clock support registered [ 1.733268] PCI host bridge to bus 0000:00 [ 1.733673] pci_bus 0000:00: root bus resource [mem 0x10000000-0x17ffffff] [ 1.734848] pci_bus 0000:00: root bus resource [io 0x1000-0x1fffff] [ 1.735084] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 1.736856] pci 0000:00:00.0: [11ab:4620] type 00 class 0x060000 [ 1.737856] pci 0000:00:00.0: [Firmware Bug]: reg 0x14: invalid BAR (can't size) [ 1.737981] pci 0000:00:00.0: [Firmware Bug]: reg 0x18: invalid BAR (can't size) [ 1.738082] pci 0000:00:00.0: [Firmware Bug]: reg 0x1c: invalid BAR (can't size) [ 1.738176] pci 0000:00:00.0: [Firmware Bug]: reg 0x20: invalid BAR (can't size) [ 1.738296] pci 0000:00:00.0: [Firmware Bug]: reg 0x24: invalid BAR (can't size) [ 1.741123] pci 0000:00:0a.0: [8086:7110] type 00 class 0x060100 [ 1.741940] pci 0000:00:0a.1: [8086:7111] type 00 class 0x010180 [ 1.742276] pci 0000:00:0a.1: reg 0x20: [io 0x0000-0x000f] [ 1.742456] pci 0000:00:0a.1: legacy IDE quirk: reg 0x10: [io 0x01f0-0x01f7] [ 1.742555] pci 0000:00:0a.1: legacy IDE quirk: reg 0x14: [io 0x03f6] [ 1.742676] pci 0000:00:0a.1: legacy IDE quirk: reg 0x18: [io 0x0170-0x0177] [ 1.742768] pci 0000:00:0a.1: legacy IDE quirk: reg 0x1c: [io 0x0376] [ 1.743261] pci 0000:00:0a.2: [8086:7112] type 00 class 0x0c0300 [ 1.743402] pci 0000:00:0a.2: reg 0x20: [io 0x0000-0x001f] [ 1.744107] pci 0000:00:0a.3: [8086:7113] type 00 class 0x068000 [ 1.744668] pci 0000:00:0a.3: quirk: [io 0x1000-0x103f] claimed by PIIX4 ACPI [ 1.744853] pci 0000:00:0a.3: quirk: [io 0x1100-0x110f] claimed by PIIX4 SMB [ 1.745473] pci 0000:00:12.0: [1234:1111] type 00 class 0x030000 [ 1.745579] pci 0000:00:12.0: reg 0x10: [mem 0x00000000-0x00ffffff pref] [ 1.745750] pci 0000:00:12.0: reg 0x18: [mem 0x00000000-0x00000fff] [ 1.745849] pci 0000:00:12.0: reg 0x30: [mem 0x00000000-0x0000ffff pref] [ 1.746371] pci 0000:00:12.0: vgaarb: VGA device added: decodes=io+mem,owns=none,locks=none [ 1.746808] pci 0000:00:13.0: [1af4:1000] type 00 class 0x020000 [ 1.746922] pci 0000:00:13.0: reg 0x10: [io 0x0000-0x001f] [ 1.747110] pci 0000:00:13.0: reg 0x20: [mem 0x00000000-0x00003fff 64bit pref] [ 1.747284] pci 0000:00:13.0: reg 0x30: [mem 0x00000000-0x0003ffff pref] [ 1.747804] pci 0000:00:14.0: [1af4:1005] type 00 class 0x00ff00 [ 1.747915] pci 0000:00:14.0: reg 0x10: [io 0x0000-0x001f] [ 1.748024] pci 0000:00:14.0: reg 0x20: [mem 0x00000000-0x00003fff 64bit pref] [ 1.748492] pci 0000:00:15.0: [1af4:1001] type 00 class 0x010000 [ 1.748601] pci 0000:00:15.0: reg 0x10: [io 0x0000-0x007f] [ 1.748707] pci 0000:00:15.0: reg 0x20: [mem 0x00000000-0x00003fff 64bit pref] [ 1.749542] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00 [ 1.751258] pci 0000:00:12.0: BAR 0: assigned [mem 0x10000000-0x10ffffff pref] [ 1.751665] pci 0000:00:13.0: BAR 6: assigned [mem 0x11000000-0x1103ffff pref] [ 1.751830] pci 0000:00:12.0: BAR 6: assigned [mem 0x11040000-0x1104ffff pref] [ 1.752060] pci 0000:00:13.0: BAR 4: assigned [mem 0x11050000-0x11053fff 64bit pref] [ 1.752247] pci 0000:00:14.0: BAR 4: assigned [mem 0x11054000-0x11057fff 64bit pref] [ 1.752369] pci 0000:00:15.0: BAR 4: assigned [mem 0x11058000-0x1105bfff 64bit pref] [ 1.752510] pci 0000:00:12.0: BAR 2: assigned [mem 0x1105c000-0x1105cfff] [ 1.752644] pci 0000:00:15.0: BAR 0: assigned [io 0x1080-0x10ff] [ 1.752750] pci 0000:00:0a.2: BAR 4: assigned [io 0x1040-0x105f] [ 1.752828] pci 0000:00:13.0: BAR 0: assigned [io 0x1060-0x107f] [ 1.752914] pci 0000:00:14.0: BAR 0: assigned [io 0x1400-0x141f] [ 1.752992] pci 0000:00:0a.1: BAR 4: assigned [io 0x1420-0x142f] [ 1.755776] clocksource: Switched to clocksource MIPS [ 1.920121] NET: Registered PF_INET protocol family [ 1.921617] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 1.935691] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear) [ 1.935975] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 1.936129] TCP established hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 1.936440] TCP bind hash table entries: 4096 (order: 4, 65536 bytes, linear) [ 1.936709] TCP: Hash tables configured (established 4096 bind 4096) [ 1.938168] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 1.938544] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 1.940549] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 1.958560] RPC: Registered named UNIX socket transport module. [ 1.958712] RPC: Registered udp transport module. [ 1.958782] RPC: Registered tcp transport module. [ 1.958845] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.960159] pci 0000:00:0a.2: enabling device (0000 -> 0001) [ 1.961121] PCI: CLS 0 bytes, default 32 [ 2.516851] workingset: timestamp_bits=46 max_order=17 bucket_order=0 [ 2.535801] NFS: Registering the id_resolver key type [ 2.537361] Key type id_resolver registered [ 2.537469] Key type id_legacy registered [ 2.540612] Key type cifs.idmap registered [ 2.585795] xor: measuring software checksum speed [ 2.593522] 8regs : 1333 MB/sec [ 2.601610] 8regs_prefetch : 1293 MB/sec [ 2.609183] 32regs : 1355 MB/sec [ 2.617358] 32regs_prefetch : 1257 MB/sec [ 2.617473] xor: using function: 32regs (1355 MB/sec) [ 2.617928] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251) [ 2.618174] io scheduler mq-deadline registered [ 2.618316] io scheduler kyber registered [ 2.623927] virtio-pci 0000:00:13.0: enabling device (0000 -> 0003) [ 2.627391] virtio-pci 0000:00:14.0: enabling device (0000 -> 0003) [ 2.628583] virtio-pci 0000:00:15.0: enabling device (0000 -> 0003) [ 2.630886] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 2.637958] printk: console [ttyS0] disabled [ 2.662068] serial8250.0: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A [ 2.662224] serial8250.0: ttyS0 extra baud rates supported: 230400, 460800 [ 2.690483] printk: console [ttyS0] enabled [ 2.713164] serial8250.0: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A [ 2.713517] serial8250.0: ttyS1 extra baud rates supported: 230400, 460800 [ 2.714096] serial8250 serial8250.0: unable to register port at index 2 (IO0 MEM1f000900 IRQ20): -28 [ 2.724015] bochs-drm 0000:00:12.0: enabling device (0000 -> 0002) [ 2.725114] [drm] Found bochs VGA, ID 0xb0c5. [ 2.726284] random: crng init done [ 2.726777] [drm] Framebuffer size 16384 kB @ 0x10000000, mmio @ 0x1105c000. [ 2.730823] [drm] Found EDID data blob. [ 2.737193] [drm] Initialized bochs-drm 1.0.0 20130925 for 0000:00:12.0 on minor 0 [ 2.815876] Console: switching to colour frame buffer device 128x48 [ 2.837827] bochs-drm 0000:00:12.0: [drm] fb0: bochs-drmdrmfb frame buffer device [ 2.876284] brd: module loaded [ 2.882887] virtio_blk virtio2: [vda] 1049604 512-byte logical blocks (537 MB/513 MiB) [ 2.909064] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.909829] ehci-pci: EHCI PCI platform driver [ 2.910521] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.911129] ohci-pci: OHCI PCI platform driver [ 2.915838] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 2.917161] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 2.922417] device-mapper: ioctl: 4.45.0-ioctl (2021-03-22) initialised: dm-devel@redhat.com [ 2.926502] usbcore: registered new interface driver usbhid [ 2.928774] usbhid: USB HID core driver [ 2.929794] u32 classifier [ 2.930119] input device check on [ 2.930475] Actions configured [ 2.933026] NET: Registered PF_INET6 protocol family [ 2.942863] Segment Routing with IPv6 [ 2.943488] In-situ OAM (IOAM) with IPv6 [ 2.944732] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.948633] NET: Registered PF_PACKET protocol family [ 2.950061] Bridge firewalling registered [ 2.951673] Key type dns_resolver registered [ 2.952714] NET: Registered PF_VSOCK protocol family [ 2.978059] Key type .fscrypt registered [ 2.985531] Key type fscrypt-provisioning registered [ 3.006390] Btrfs loaded, crc32c=crc32c-generic, zoned=no, fsverity=no [ 3.028477] input: AT Raw Set 2 keyboard as /devices/platform/i8042/serio0/input/input0 [ 3.056358] Key type encrypted registered [ 3.076113] printk: console [netcon0] enabled [ 3.081807] netconsole: network logging started [ 3.698957] input: ImExPS/2 Generic Explorer Mouse as /devices/platform/i8042/serio1/input/input2 [ 3.806671] IP-Config: Complete: [ 3.829872] device=eth0, hwaddr=52:54:00:12:34:08, ipaddr=192.168.7.8, mask=255.255.255.0, gw=192.168.7.7 [ 3.848321] host=192.168.7.8, domain=, nis-domain=(none) [ 3.872210] bootserver=255.255.255.255, rootserver=255.255.255.255, rootpath= [ 3.872405] nameserver0=8.8.8.8 [ 3.923358] md: Waiting for all devices to be available before autodetect [ 3.942415] md: If you don't use raid, use raid=noautodetect [ 3.954710] md: Autodetecting RAID arrays. [ 3.972538] md: autorun ... [ 3.983354] md: ... autorun DONE. [ 4.022351] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 4.071868] EXT4-fs (vda): mounted filesystem with ordered data mode. Opts: (null). Quota mode: disabled. [ 4.095004] VFS: Mounted root (ext4 filesystem) on device 253:0. [ 4.107821] devtmpfs: mounted [ 4.157566] Freeing unused kernel image (initmem) memory: 432K [ 4.165474] This architecture does not have kernel memory protection. [ 4.171410] Run /sbin/init as init process [ 4.207846] process '/sbin/init.sysvinit' started with executable stack [ 7.025872] udevd[118]: starting version 3.2.10 [ 7.157085] udevd[119]: starting eudev-3.2.10 [ 19.268418] EXT4-fs (vda): re-mounted. Opts: (null). Quota mode: disabled. hwclock: can't open '/dev/misc/rtc': No such file or directory ALSA: Restoring mixer settings... INIT: bootlogd: writing to console: Input/output error Entering runlevel: 5 Configuring network interfaces... ip: RTNETLINK answers: File exists Starting system message bus: dbus. Starting Connection Manager Starting Xserver Starting Dropbear SSH server: dropbear. X.Org X Server 1.21.1.4 X Protocol Version 11, Revision 0 Current Operating System: Linux qemumips64 5.15.78-yocto-standard #1 SMP PREEMPT Wed Nov 16 14:15:49 UTC 2022 mips64 Kernel command line: root=/dev/vda rw ip=192.168.7.8::192.168.7.7:255.255.255.0::eth0:off:8.8.8.8 console=ttyS0 console=ttyS1 console=ttyS0 console=tty printk.time=1 Current version of pixman: 0.40.0 Before reporting problems, check http://wiki.x.org to make sure that you have the latest version. Markers: (--) probed, (**) from config file, (==) default setting, (++) from command line, (!!) notice, (II) informational, (WW) warning, (EE) error, (NI) not implemented, (??) unknown. (==) Log file: "/var/log/Xorg.0.log", Time: Wed Jan 11 16:50:16 2023 (==) Using system config directory "/usr/share/X11/xorg.conf.d" Starting rpcbind daemon...done. Starting bluetooth: bluetoothd. hwclock: can't open '/dev/misc/rtc': No such file or directory Starting syslogd/klogd: The XKEYBOARD keymap compiler (xkbcomp) reports: > Warning: Could not resolve keysym XF86EmojiPicker Errors from xkbcomp are not fatal to the X server done * Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon ...done. Starting Telephony daemon D-BUS per-session daemon address is: unix:path=/tmp/dbus-srA5uxaYYL,guid=e14f7aae35f4f9ca41b13e2e63bee8cd Using calibration data stored in /etc/pointercal.xinput Poky (Yocto Project Reference Distro) 4.0.6 qemumips64 /dev/ttyS0 qemumips64 login: