[ 0.000000] Linux version 5.19.17-yocto-standard (oe-user@oe-host) (mips-poky-linux-gcc (GCC) 12.2.0, GNU ld (GNU Binutils) 2.40.20230115) #1 SMP PREEMPT Mon Jan 2 02:58:01 UTC 2023 [ 0.000000] earlycon: uart8250 at I/O port 0x3f8 (options '38400n8') [ 0.000000] printk: bootconsole [uart8250] enabled [ 0.000000] CPU0 revision is: 00019500 (MIPS 34Kc) [ 0.000000] FPU revision is: 00739500 [ 0.000000] OF: fdt: No chosen node found, continuing without [ 0.000000] MIPS: machine is mti,malta [ 0.000000] Software DMA cache coherency enabled [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Primary instruction cache 2kB, VIPT, 2-way, linesize 16 bytes. [ 0.000000] Primary data cache 2kB, 2-way, VIPT, no aliases, linesize 16 bytes [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000000000000-0x0000000000ffffff] [ 0.000000] Normal [mem 0x0000000001000000-0x000000000fffefff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffefff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffefff] [ 0.000000] percpu: Embedded 16 pages/cpu s35168 r8192 d22176 u65536 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64959 [ 0.000000] Kernel command line: root=/dev/vda rw ip=192.168.7.8::192.168.7.7:255.255.255.0::eth0:off:8.8.8.8 console=ttyS0 console=ttyS1 console=ttyS0 console=tty printk.time=1 [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off [ 0.000000] Memory: 239424K/262140K available (13339K kernel code, 1409K rwdata, 3504K rodata, 424K init, 399K bss, 22716K reserved, 0K cma-reserved, 0K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] trace event string verifier disabled [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. [ 0.000000] Trampoline variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 [ 0.000000] NR_IRQS: 256 [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] CPU frequency 333.54 MHz [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11460449569 ns [ 0.000375] sched_clock: 32 bits at 167MHz, resolution 5ns, wraps every 12876909565ns [ 0.021794] Console: colour dummy device 80x25 [ 0.023243] printk: console [tty0] enabled [ 0.024471] printk: bootconsole [uart8250] disabled [ 0.000000] Linux version 5.19.17-yocto-standard (oe-user@oe-host) (mips-poky-linux-gcc (GCC) 12.2.0, GNU ld (GNU Binutils) 2.40.20230115) #1 SMP PREEMPT Mon Jan 2 02:58:01 UTC 2023 [ 0.000000] earlycon: uart8250 at I/O port 0x3f8 (options '38400n8') [ 0.000000] printk: bootconsole [uart8250] enabled [ 0.000000] CPU0 revision is: 00019500 (MIPS 34Kc) [ 0.000000] FPU revision is: 00739500 [ 0.000000] OF: fdt: No chosen node found, continuing without [ 0.000000] MIPS: machine is mti,malta [ 0.000000] Software DMA cache coherency enabled [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Primary instruction cache 2kB, VIPT, 2-way, linesize 16 bytes. [ 0.000000] Primary data cache 2kB, 2-way, VIPT, no aliases, linesize 16 bytes [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000000000000-0x0000000000ffffff] [ 0.000000] Normal [mem 0x0000000001000000-0x000000000fffefff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffefff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffefff] [ 0.000000] percpu: Embedded 16 pages/cpu s35168 r8192 d22176 u65536 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64959 [ 0.000000] Kernel command line: root=/dev/vda rw ip=192.168.7.8::192.168.7.7:255.255.255.0::eth0:off:8.8.8.8 console=ttyS0 console=ttyS1 console=ttyS0 console=tty printk.time=1 [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off [ 0.000000] Memory: 239424K/262140K available (13339K kernel code, 1409K rwdata, 3504K rodata, 424K init, 399K bss, 22716K reserved, 0K cma-reserved, 0K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] trace event string verifier disabled [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. [ 0.000000] Trampoline variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 [ 0.000000] NR_IRQS: 256 [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] CPU frequency 333.54 MHz [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11460449569 ns [ 0.000375] sched_clock: 32 bits at 167MHz, resolution 5ns, wraps every 12876909565ns [ 0.021794] Console: colour dummy device 80x25 [ 0.023243] printk: console [tty0] enabled [ 0.024471] printk: bootconsole [uart8250] disabled [ 0.028346] Calibrating delay loop... 864.25 BogoMIPS (lpj=4321280) [ 0.114127] pid_max: default: 32768 minimum: 301 [ 0.116036] LSM: Security Framework initializing [ 0.117998] landlock: Up and running. [ 0.124565] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.124890] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.196727] cblist_init_generic: Setting adjustable number of callback queues. [ 0.197143] cblist_init_generic: Setting shift to 0 and lim to 1. [ 0.198030] cblist_init_generic: Setting shift to 0 and lim to 1. [ 0.199399] Performance counters: No available PMU. [ 0.201214] rcu: Hierarchical SRCU implementation. [ 0.201341] rcu: Max phase no-delay instances is 1000. [ 0.216412] smp: Bringing up secondary CPUs ... [ 0.216707] smp: Brought up 1 node, 1 CPU [ 0.240885] devtmpfs: initialized [ 0.256128] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.256675] futex hash table entries: 256 (order: 2, 16384 bytes, linear) [ 0.274299] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.732414] raid6: int32x8 gen() 99 MB/s [ 1.083335] raid6: int32x4 gen() 290 MB/s [ 1.434444] raid6: int32x2 gen() 395 MB/s [ 1.783499] raid6: int32x1 gen() 401 MB/s [ 1.783699] raid6: using algorithm int32x1 gen() 401 MB/s [ 2.009057] raid6: .... xor() 272 MB/s, rmw enabled [ 2.009381] raid6: using intx1 recovery algorithm [ 2.012444] SCSI subsystem initialized [ 2.013216] usbcore: registered new interface driver usbfs [ 2.013579] usbcore: registered new interface driver hub [ 2.013839] usbcore: registered new device driver usb [ 2.014341] pps_core: LinuxPPS API ver. 1 registered [ 2.014415] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 2.014608] PTP clock support registered [ 2.033566] PCI host bridge to bus 0000:00 [ 2.033991] pci_bus 0000:00: root bus resource [mem 0x10000000-0x17ffffff] [ 2.034612] pci_bus 0000:00: root bus resource [io 0x1000-0x1fffff] [ 2.034802] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 2.036422] pci 0000:00:00.0: [11ab:4620] type 00 class 0x060000 [ 2.037297] pci 0000:00:00.0: [Firmware Bug]: reg 0x14: invalid BAR (can't size) [ 2.037410] pci 0000:00:00.0: [Firmware Bug]: reg 0x18: invalid BAR (can't size) [ 2.037497] pci 0000:00:00.0: [Firmware Bug]: reg 0x1c: invalid BAR (can't size) [ 2.037578] pci 0000:00:00.0: [Firmware Bug]: reg 0x20: invalid BAR (can't size) [ 2.037672] pci 0000:00:00.0: [Firmware Bug]: reg 0x24: invalid BAR (can't size) [ 2.041109] pci 0000:00:0a.0: [8086:7110] type 00 class 0x060100 [ 2.041867] pci 0000:00:0a.1: [8086:7111] type 00 class 0x010180 [ 2.042173] pci 0000:00:0a.1: reg 0x20: [io 0x0000-0x000f] [ 2.042326] pci 0000:00:0a.1: legacy IDE quirk: reg 0x10: [io 0x01f0-0x01f7] [ 2.042415] pci 0000:00:0a.1: legacy IDE quirk: reg 0x14: [io 0x03f6] [ 2.042520] pci 0000:00:0a.1: legacy IDE quirk: reg 0x18: [io 0x0170-0x0177] [ 2.042606] pci 0000:00:0a.1: legacy IDE quirk: reg 0x1c: [io 0x0376] [ 2.043046] pci 0000:00:0a.2: [8086:7112] type 00 class 0x0c0300 [ 2.043168] pci 0000:00:0a.2: reg 0x20: [io 0x0000-0x001f] [ 2.043856] pci 0000:00:0a.3: [8086:7113] type 00 class 0x068000 [ 2.044463] pci 0000:00:0a.3: quirk: [io 0x1000-0x103f] claimed by PIIX4 ACPI [ 2.044662] pci 0000:00:0a.3: quirk: [io 0x1100-0x110f] claimed by PIIX4 SMB [ 2.045482] pci 0000:00:12.0: [1234:1111] type 00 class 0x030000 [ 2.045581] pci 0000:00:12.0: reg 0x10: [mem 0x00000000-0x00ffffff pref] [ 2.045736] pci 0000:00:12.0: reg 0x18: [mem 0x00000000-0x00000fff] [ 2.045828] pci 0000:00:12.0: reg 0x30: [mem 0x00000000-0x0000ffff pref] [ 2.046359] pci 0000:00:13.0: [1af4:1000] type 00 class 0x020000 [ 2.046486] pci 0000:00:13.0: reg 0x10: [io 0x0000-0x001f] [ 2.046673] pci 0000:00:13.0: reg 0x20: [mem 0x00000000-0x00003fff 64bit pref] [ 2.046826] pci 0000:00:13.0: reg 0x30: [mem 0x00000000-0x0003ffff pref] [ 2.047216] pci 0000:00:14.0: [1af4:1005] type 00 class 0x00ff00 [ 2.047323] pci 0000:00:14.0: reg 0x10: [io 0x0000-0x001f] [ 2.047423] pci 0000:00:14.0: reg 0x20: [mem 0x00000000-0x00003fff 64bit pref] [ 2.047859] pci 0000:00:15.0: [1af4:1001] type 00 class 0x010000 [ 2.048040] pci 0000:00:15.0: reg 0x10: [io 0x0000-0x007f] [ 2.048166] pci 0000:00:15.0: reg 0x20: [mem 0x00000000-0x00003fff 64bit pref] [ 2.048932] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00 [ 2.050597] pci 0000:00:12.0: BAR 0: assigned [mem 0x10000000-0x10ffffff pref] [ 2.050955] pci 0000:00:13.0: BAR 6: assigned [mem 0x11000000-0x1103ffff pref] [ 2.051108] pci 0000:00:12.0: BAR 6: assigned [mem 0x11040000-0x1104ffff pref] [ 2.051230] pci 0000:00:13.0: BAR 4: assigned [mem 0x11050000-0x11053fff 64bit pref] [ 2.051397] pci 0000:00:14.0: BAR 4: assigned [mem 0x11054000-0x11057fff 64bit pref] [ 2.051505] pci 0000:00:15.0: BAR 4: assigned [mem 0x11058000-0x1105bfff 64bit pref] [ 2.051637] pci 0000:00:12.0: BAR 2: assigned [mem 0x1105c000-0x1105cfff] [ 2.051764] pci 0000:00:15.0: BAR 0: assigned [io 0x1080-0x10ff] [ 2.051863] pci 0000:00:0a.2: BAR 4: assigned [io 0x1040-0x105f] [ 2.051936] pci 0000:00:13.0: BAR 0: assigned [io 0x1060-0x107f] [ 2.052017] pci 0000:00:14.0: BAR 0: assigned [io 0x1400-0x141f] [ 2.052100] pci 0000:00:0a.1: BAR 4: assigned [io 0x1420-0x142f] [ 2.054099] pci 0000:00:12.0: vgaarb: setting as boot VGA device [ 2.054248] pci 0000:00:12.0: vgaarb: bridge control possible [ 2.054363] pci 0000:00:12.0: vgaarb: VGA device added: decodes=io+mem,owns=none,locks=none [ 2.054496] vgaarb: loaded [ 2.056818] clocksource: Switched to clocksource MIPS [ 2.223757] NET: Registered PF_INET protocol family [ 2.225384] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 2.235038] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 2.235284] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 2.235432] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 2.235688] TCP bind hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 2.235879] TCP: Hash tables configured (established 2048 bind 2048) [ 2.237891] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 2.238225] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 2.240153] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 2.243118] RPC: Registered named UNIX socket transport module. [ 2.243235] RPC: Registered udp transport module. [ 2.243295] RPC: Registered tcp transport module. [ 2.243349] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 2.244122] pci 0000:00:0a.2: enabling device (0000 -> 0001) [ 2.245044] PCI: CLS 0 bytes, default 16 [ 2.255415] workingset: timestamp_bits=14 max_order=16 bucket_order=2 [ 2.274011] NFS: Registering the id_resolver key type [ 2.275684] Key type id_resolver registered [ 2.275799] Key type id_legacy registered [ 2.279714] Key type cifs.idmap registered [ 2.463541] xor: measuring software checksum speed [ 2.485825] 8regs : 466 MB/sec [ 2.508417] 8regs_prefetch : 447 MB/sec [ 2.530417] 32regs : 454 MB/sec [ 2.554054] 32regs_prefetch : 438 MB/sec [ 2.554359] xor: using function: 8regs (466 MB/sec) [ 2.555525] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251) [ 2.555908] io scheduler mq-deadline registered [ 2.556130] io scheduler kyber registered [ 2.573885] virtio-pci 0000:00:13.0: enabling device (0000 -> 0003) [ 2.579302] virtio-pci 0000:00:14.0: enabling device (0000 -> 0003) [ 2.581076] virtio-pci 0000:00:15.0: enabling device (0000 -> 0003) [ 2.584525] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 2.595839] printk: console [ttyS0] disabled [ 2.624071] serial8250.0: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A [ 2.624407] serial8250.0: ttyS0 extra baud rates supported: 230400, 460800 [ 2.660479] printk: console [ttyS0] enabled [ 2.691027] serial8250.0: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A [ 2.691539] serial8250.0: ttyS1 extra baud rates supported: 230400, 460800 [ 2.692625] serial8250 serial8250.0: unable to register port at index 2 (IO0 MEM1f000900 IRQ20): -28 [ 2.706667] bochs-drm 0000:00:12.0: vgaarb: deactivate vga console [ 2.710428] bochs-drm 0000:00:12.0: enabling device (0000 -> 0002) [ 2.712028] [drm] Found bochs VGA, ID 0xb0c5. [ 2.712389] [drm] Framebuffer size 16384 kB @ 0x10000000, mmio @ 0x1105c000. [ 2.718163] random: crng init done [ 2.721593] [drm] Found EDID data blob. [ 2.733435] [drm] Initialized bochs-drm 1.0.0 20130925 for 0000:00:12.0 on minor 0 [ 2.866207] Console: switching to colour frame buffer device 160x50 [ 2.897794] bochs-drm 0000:00:12.0: [drm] fb0: bochs-drmdrmfb frame buffer device [ 2.961267] brd: module loaded [ 2.963312] virtio_blk virtio2: 1/0/0 default/read/poll queues [ 2.974147] virtio_blk virtio2: [vda] 5675638 512-byte logical blocks (2.91 GB/2.71 GiB) [ 3.013910] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.015073] ehci-pci: EHCI PCI platform driver [ 3.016159] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 3.017398] ohci-pci: OHCI PCI platform driver [ 3.018480] uhci_hcd: USB Universal Host Controller Interface driver [ 3.021372] uhci_hcd 0000:00:0a.2: UHCI Host Controller [ 3.024225] uhci_hcd 0000:00:0a.2: new USB bus registered, assigned bus number 1 [ 3.026706] uhci_hcd 0000:00:0a.2: irq 11, io port 0x00001040 [ 3.042465] hub 1-0:1.0: USB hub found [ 3.044352] hub 1-0:1.0: 2 ports detected [ 3.057318] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 3.058899] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 3.064835] device-mapper: ioctl: 4.47.0-ioctl (2022-07-28) initialised: dm-devel@redhat.com [ 3.072018] usbcore: registered new interface driver usbhid [ 3.075899] usbhid: USB HID core driver [ 3.078002] u32 classifier [ 3.078385] input device check on [ 3.078787] Actions configured [ 3.081671] NET: Registered PF_INET6 protocol family [ 3.093046] Segment Routing with IPv6 [ 3.094279] In-situ OAM (IOAM) with IPv6 [ 3.118270] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 3.143371] NET: Registered PF_PACKET protocol family [ 3.165466] Bridge firewalling registered [ 3.191166] input: AT Raw Set 2 keyboard as /devices/platform/i8042/serio0/input/input0 [ 3.218087] Key type dns_resolver registered [ 3.238167] NET: Registered PF_VSOCK protocol family [ 3.276532] Key type ._fscrypt registered [ 3.300156] Key type .fscrypt registered [ 3.324567] Key type fscrypt-provisioning registered [ 3.357788] Btrfs loaded, crc32c=crc32c-generic, zoned=no, fsverity=no [ 3.410451] Key type encrypted registered [ 3.427011] usb 1-1: new full-speed USB device number 2 using uhci_hcd [ 3.491453] printk: console [netcon0] enabled [ 3.513008] netconsole: network logging started [ 3.730671] input: QEMU QEMU USB Tablet as /devices/pci0000:00/0000:00:0a.2/usb1/1-1/1-1:1.0/0003:0627:0001.0001/input/input3 [ 3.745040] hid-generic 0003:0627:0001.0001: input: USB HID v0.01 Mouse [QEMU QEMU USB Tablet] on usb-0000:00:0a.2-1/input0 [ 3.880544] input: ImExPS/2 Generic Explorer Mouse as /devices/platform/i8042/serio1/input/input2 [ 3.977412] IP-Config: Complete: [ 3.996888] device=eth0, hwaddr=52:54:00:12:34:08, ipaddr=192.168.7.8, mask=255.255.255.0, gw=192.168.7.7 [ 4.016818] host=192.168.7.8, domain=, nis-domain=(none) [ 4.040690] bootserver=255.255.255.255, rootserver=255.255.255.255, rootpath= [ 4.040892] nameserver0=8.8.8.8 [ 4.085023] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 4.128281] md: Waiting for all devices to be available before autodetect [ 4.156823] md: If you don't use raid, use raid=noautodetect [ 4.176669] md: Autodetecting RAID arrays. [ 4.206756] md: autorun ... [ 4.215992] md: ... autorun DONE. [ 4.321825] EXT4-fs (vda): mounted filesystem with ordered data mode. Quota mode: disabled. [ 4.342174] VFS: Mounted root (ext4 filesystem) on device 253:0. [ 4.370896] devtmpfs: mounted [ 4.501941] Freeing unused kernel image (initmem) memory: 424K [ 4.526723] This architecture does not have kernel memory protection. [ 4.546998] Run /sbin/init as init process [ 4.611758] process '/sbin/init.sysvinit' started with executable stack [ 9.242347] udevd[124]: starting version 3.2.11 [ 9.459748] udevd[125]: starting eudev-3.2.11 [ 23.979001] EXT4-fs (vda): re-mounted. Quota mode: disabled. hwclock: Cannot access the Hardware Clock via any known method. hwclock: Use the --verbose option to see the details of our search for an access method. ALSA: Restoring mixer settings... INIT: Entering runlevel: 5bootlogd: writing to console: Input/output error Configuring network interfaces... RTNETLINK answers: File exists Starting system message bus: dbus. Starting Connection Manager Starting OpenBSD Secure Shell server: sshd done. Starting Xserver Starting rpcbind daemon... done. X.Org X Server 1.21.1.6 X Protocol Version 11, Revision 0 Current Operating System: Linux qemumips 5.19.17-yocto-standard #1 SMP PREEMPT Mon Jan 2 02:58:01 UTC 2023 mips Kernel command line: root=/dev/vda rw ip=192.168.7.8::192.168.7.7:255.255.255.0::eth0:off:8.8.8.8 console=ttyS0 console=ttyS1 console=ttyS0 console=tty printk.time=1 Current version of pixman: 0.42.2 Before reporting problems, check http://wiki.x.org to make sure that you have the latest version. Markers: (--) probed, (**) from config file, (==) default setting, (++) from command line, (!!) notice, (II) informational, (WW) warning, (EE) error, (NI) not implemented, (??) unknown. (==) Log file: "/var/log/Xorg.0.log", Time: Tue Jan 17 07:29:42 2023 (==) Using system config directory "/usr/share/X11/xorg.conf.d" Starting bluetooth: bluetoothd. hwclock: Cannot access the Hardware Clock via any known method. hwclock: Use the --verbose option to see the details of our search for an access method. Starting syslogd/klogd: done * Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon [A[154G[ ok ] Starting Telephony daemon Starting crond: OK Poky (Yocto Project Reference Distro) 4.1 qemumips ttyS0 qemumips login: [ 1686.818426] hellomod: loading out-of-tree module taints kernel. [ 1686.838770] Hello world! [ 1689.500728] Cleaning up hellomod.