[ 1.148060] [drm] features: -virgl +edid -resource_blob -host_visible [ 1.148063] [drm] features: -context_init [ 1.149617] [drm] number of scanouts: 1 [ 1.150032] [drm] number of cap sets: 0 [ 1.150852] [drm] Initialized virtio_gpu 0.1.0 0 for 0000:00:06.0 on minor 0 [ 1.154994] virtio-pci 0000:00:06.0: [drm] drm_plane_enable_fb_damage_clips() not called [ 1.183958] Console: switching to colour frame buffer device 160x50 [ 1.204393] virtio-pci 0000:00:06.0: [drm] fb0: virtio_gpudrmfb frame buffer device [ 1.211289] cacheinfo: Unable to detect cache hierarchy for CPU 0 [ 1.214097] brd: module loaded [ 1.214882] virtio_blk virtio2: 4/0/0 default/read/poll queues [ 1.216530] virtio_blk virtio2: [vda] 878544 512-byte logical blocks (450 MB/429 MiB) [ 1.223475] xhci_hcd 0000:00:04.0: xHCI Host Controller [ 1.224178] xhci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 1 [ 1.225253] xhci_hcd 0000:00:04.0: hcc params 0x00087001 hci version 0x100 quirks 0x0000000000000010 [ 1.227048] xhci_hcd 0000:00:04.0: xHCI Host Controller [ 1.227725] xhci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 2 [ 1.228517] xhci_hcd 0000:00:04.0: Host supports USB 3.0 SuperSpeed [ 1.229599] hub 1-0:1.0: USB hub found [ 1.230144] hub 1-0:1.0: 4 ports detected [ 1.230903] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 1.232044] hub 2-0:1.0: USB hub found [ 1.232554] hub 2-0:1.0: 4 ports detected [ 1.233938] rtc-pl031 9010000.pl031: registered as rtc0 [ 1.234551] rtc-pl031 9010000.pl031: setting system clock to 2023-03-31T00:02:48 UTC (1680220968) [ 1.235999] device-mapper: ioctl: 4.47.0-ioctl (2022-07-28) initialised: dm-devel@redhat.com [ 1.237276] usbcore: registered new interface driver usbhid [ 1.237886] usbhid: USB HID core driver [ 1.238283] u32 classifier [ 1.238573] input device check on [ 1.238915] Actions configured [ 1.239526] NET: Registered PF_INET6 protocol family [ 1.240656] Segment Routing with IPv6 [ 1.241085] In-situ OAM (IOAM) with IPv6 [ 1.241505] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 1.242439] NET: Registered PF_PACKET protocol family [ 1.243130] Bridge firewalling registered [ 1.243632] Key type dns_resolver registered [ 1.244330] NET: Registered PF_VSOCK protocol family [ 1.245208] registered taskstats version 1 [ 1.245944] Key type .fscrypt registered [ 1.246427] Key type fscrypt-provisioning registered [ 1.337068] Btrfs loaded, crc32c=crc32c-generic, zoned=no, fsverity=no [ 1.338981] Key type encrypted registered [ 1.342377] printk: console [netcon0] enabled [ 1.343094] netconsole: network logging started [ 1.363390] IP-Config: Complete: [ 1.364591] device=eth0, hwaddr=52:54:00:12:34:06, ipaddr=192.168.7.6, mask=255.255.255.0, gw=192.168.7.5 [ 1.374524] host=192.168.7.6, domain=, nis-domain=(none) [ 1.374994] bootserver=255.255.255.255, rootserver=255.255.255.255, rootpath= [ 1.375000] nameserver0=8.8.8.8 [ 1.376968] md: Waiting for all devices to be available before autodetect [ 1.377542] md: If you don't use raid, use raid=noautodetect [ 1.378046] md: Autodetecting RAID arrays. [ 1.378486] md: autorun ... [ 1.378755] md: ... autorun DONE. [ 1.395951] EXT4-fs (vda): mounted filesystem with ordered data mode. Quota mode: disabled. [ 1.396923] VFS: Mounted root (ext4 filesystem) on device 253:0. [ 1.397729] devtmpfs: mounted [ 1.400316] Freeing unused kernel memory: 3840K [ 1.411965] Run /sbin/init as init process INIT: version 3.04 booting [ 1.579364] usb 1-1: new high-speed USB device number 2 using xhci_hcd [ 1.792148] input: QEMU QEMU USB Tablet as /devices/platform/4010000000.pcie/pci0000:00/0000:00:04.0/usb1/1-1/1-1:1.0/0003:0627:0001.0001/input/input0 [ 1.793912] hid-generic 0003:0627:0001.0001: input: USB HID v0.01 Mouse [QEMU QEMU USB Tablet] on usb-0000:00:04.0-1/input0 Starting udev [ 1.931308] usb 1-2: new high-speed USB device number 3 using xhci_hcd [ 1.966843] udevd[138]: starting version 3.2.11 [ 1.979918] udevd[139]: starting eudev-3.2.11 [ 2.173206] input: QEMU QEMU USB Keyboard as /devices/platform/4010000000.pcie/pci0000:00/0000:00:04.0/usb1/1-2/1-2:1.0/0003:0627:0001.0002/input/input1 [ 2.227323] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 2.235485] hid-generic 0003:0627:0001.0002: input: USB HID v1.11 Keyboard [QEMU QEMU USB Keyboard] on usb-0000:00:04.0-2/input0 [ 2.378895] EXT4-fs (vda): re-mounted. Quota mode: disabled. Configuring packages on first boot.... (This may take several minutes. Please do not power off the machine.) Running postinst /etc/rpm-postinsts/100-sysvinit-inittab... update-rc.d: /etc/init.d/run-postinsts exists during rc.d purge (continuing) Removing any system startup links for run-postinsts ... /etc/rcS.d/S99run-postinsts INIT: Entering runlevel: 5 Configuring network interfaces... RTNETLINK answers: File exists Starting OpenBSD Secure Shell server: sshd generating ssh RSA host key... generating ssh ECDSA host key... generating ssh ED25519 host key... done. Starting syslogd/klogd: done Poky (Yocto Project Reference Distro) 4.1+snapshot-624b4edf369f68699d813d02e46f69fa318c9a13 qemuarm64 hvc0 qemuarm64 login: [ 16.428319] loop: module loaded [ 16.715547] loop0: detected capacity change from 0 to 20480 [ 24.109658] hrtimer: interrupt took 26481840 ns [ 25.045159] loop0: detected capacity change from 0 to 102400 [ 25.053084] loop1: detected capacity change from 0 to 102400 [ 25.322476] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1) [ 25.323534] scsi host0: scsi_debug: version 0191 [20210520] [ 25.323534] dev_size_mb=51, opts=0x0, submit_queues=1, statistics=0 [ 25.329204] scsi 0:0:0:0: Direct-Access Linux scsi_debug 0191 PQ: 0 ANSI: 7 [ 25.330034] sd 0:0:0:0: Power-on or device reset occurred [ 25.338607] sd 0:0:0:0: [sda] 104448 512-byte logical blocks: (53.5 MB/51.0 MiB) [ 25.347912] sd 0:0:0:0: [sda] Write Protect is off [ 25.356394] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA [ 25.371900] sd 0:0:0:0: [sda] Preferred minimum I/O size 512 bytes [ 25.372495] sd 0:0:0:0: [sda] Optimal transfer size 524288 bytes [ 25.409752] sd 0:0:0:0: [sda] Attached SCSI disk [ 25.813471] sda: sda1 sda2 [ 26.028712] sda: sda1 sda2 [ 26.551308] sd 0:0:0:0: [sda] Synchronizing SCSI cache [ 26.716435] loop0: detected capacity change from 0 to 102400 [ 26.726110] loop1: detected capacity change from 0 to 102400 [ 32.126696] loop0: detected capacity change from 0 to 8 [ 36.100472] loop0: detected capacity change from 0 to 120 [ 36.909820] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1) [ 36.915708] scsi host0: scsi_debug: version 0191 [20210520] [ 36.915708] dev_size_mb=100, opts=0x0, submit_queues=1, statistics=0 [ 36.916860] scsi 0:0:0:0: Direct-Access Linux scsi_debug 0191 PQ: 0 ANSI: 7 [ 36.917679] sd 0:0:0:0: Power-on or device reset occurred [ 36.931080] sd 0:0:0:0: [sda] 204800 512-byte logical blocks: (105 MB/100 MiB) [ 36.940701] sd 0:0:0:0: [sda] Write Protect is off [ 36.949373] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA [ 36.962359] sd 0:0:0:0: [sda] Preferred minimum I/O size 512 bytes [ 36.963083] sd 0:0:0:0: [sda] Optimal transfer size 524288 bytes [ 37.000584] sd 0:0:0:0: [sda] Attached SCSI disk [ 38.050339] sd 0:0:0:0: [sda] Spinning up disk... [ 39.055406] .ready [ 39.143463] sd 0:0:0:0: [sda] Synchronizing SCSI cache [ 39.286581] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1) [ 39.287637] scsi host0: scsi_debug: version 0191 [20210520] [ 39.287637] dev_size_mb=100, opts=0x0, submit_queues=1, statistics=0 [ 39.288737] scsi 0:0:0:0: Direct-Access Linux scsi_debug 0191 PQ: 0 ANSI: 7 [ 39.289522] sd 0:0:0:0: Power-on or device reset occurred [ 39.298091] sd 0:0:0:0: [sda] 204800 512-byte logical blocks: (105 MB/100 MiB) [ 39.302900] sd 0:0:0:0: [sda] Write Protect is off [ 39.311495] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA [ 39.324331] sd 0:0:0:0: [sda] Preferred minimum I/O size 512 bytes [ 39.324871] sd 0:0:0:0: [sda] Optimal transfer size 524288 bytes [ 39.362277] sd 0:0:0:0: [sda] Attached SCSI disk [ 40.088726] EXT4-fs (sda): mounting ext2 file system using the ext4 subsystem [ 40.102351] EXT4-fs (sda): mounted filesystem without journal. Quota mode: disabled. [ 40.159906] EXT4-fs (sda): unmounting filesystem. [ 41.181493] sd 0:0:0:0: [sda] Spinning up disk... [ 42.195291] .ready [ 42.287473] sd 0:0:0:0: [sda] Synchronizing SCSI cache [ 42.496991] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1) [ 42.498063] scsi host0: scsi_debug: version 0191 [20210520] [ 42.498063] dev_size_mb=100, opts=0x0, submit_queues=1, statistics=0 [ 42.499487] scsi 0:0:0:0: Direct-Access Linux scsi_debug 0191 PQ: 0 ANSI: 7 [ 42.500512] sd 0:0:0:0: Power-on or device reset occurred [ 42.509189] sd 0:0:0:0: [sda] 204800 512-byte logical blocks: (105 MB/100 MiB) [ 42.513904] sd 0:0:0:0: [sda] Write Protect is off [ 42.522430] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA [ 42.535459] sd 0:0:0:0: [sda] Preferred minimum I/O size 512 bytes [ 42.536054] sd 0:0:0:0: [sda] Optimal transfer size 524288 bytes [ 42.573303] sd 0:0:0:0: [sda] Attached SCSI disk [ 42.990754] sda: sda1 sda2 [ 43.964661] EXT4-fs (sda1): mounting ext2 file system using the ext4 subsystem [ 43.985673] EXT4-fs (sda1): mounted filesystem without journal. Quota mode: disabled. [ 44.078554] EXT4-fs (sda2): mounting ext2 file system using the ext4 subsystem [ 44.092290] EXT4-fs (sda2): mounted filesystem without journal. Quota mode: disabled. [ 44.150894] EXT4-fs (sda2): unmounting filesystem. [ 44.210023] EXT4-fs (sda1): unmounting filesystem. [ 45.231928] sd 0:0:0:0: [sda] Spinning up disk... [ 46.255357] .ready [ 46.292922] sda: sda1 sda2 [ 46.391444] sd 0:0:0:0: [sda] Synchronizing SCSI cache [ 46.607039] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1) [ 46.608010] scsi host0: scsi_debug: version 0191 [20210520] [ 46.608010] dev_size_mb=100, opts=0x0, submit_queues=1, statistics=0 [ 46.609088] scsi 0:0:0:0: Direct-Access Linux scsi_debug 0191 PQ: 0 ANSI: 7 [ 46.609905] sd 0:0:0:0: Power-on or device reset occurred [ 46.628021] sd 0:0:0:0: [sda] 204800 512-byte logical blocks: (105 MB/100 MiB) [ 46.635435] sd 0:0:0:0: [sda] Write Protect is off [ 46.643898] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA [ 46.656716] sd 0:0:0:0: [sda] Preferred minimum I/O size 512 bytes [ 46.657241] sd 0:0:0:0: [sda] Optimal transfer size 524288 bytes [ 46.694649] sd 0:0:0:0: [sda] Attached SCSI disk [ 47.095949] sda: sda1 sda2 [ 48.992792] sd 0:0:0:0: [sda] Spinning up disk... [ 49.999284] .ready [ 50.036557] sda: sda1 sda2 [ 50.287339] sd 0:0:0:0: [sda] Synchronizing SCSI cache [ 50.639449] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1) [ 50.640482] scsi host0: scsi_debug: version 0191 [20210520] [ 50.640482] dev_size_mb=100, opts=0x0, submit_queues=1, statistics=0 [ 50.641578] scsi 0:0:0:0: Direct-Access Linux scsi_debug 0191 PQ: 0 ANSI: 7 [ 50.642409] sd 0:0:0:0: Power-on or device reset occurred [ 50.651029] sd 0:0:0:0: [sda] 204800 512-byte logical blocks: (105 MB/100 MiB) [ 50.663977] sd 0:0:0:0: [sda] Write Protect is off [ 50.672452] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA [ 50.685254] sd 0:0:0:0: [sda] Preferred minimum I/O size 512 bytes [ 50.685975] sd 0:0:0:0: [sda] Optimal transfer size 524288 bytes [ 50.723279] sd 0:0:0:0: [sda] Attached SCSI disk [ 51.235968] sda: sda1 sda2 [ 52.216432] EXT4-fs (sda1): mounting ext2 file system using the ext4 subsystem [ 52.233367] EXT4-fs (sda1): mounted filesystem without journal. Quota mode: disabled. [ 52.321145] EXT4-fs (sda2): mounting ext2 file system using the ext4 subsystem [ 52.334314] EXT4-fs (sda2): mounted filesystem without journal. Quota mode: disabled. [ 52.388172] EXT4-fs (sda2): unmounting filesystem. [ 52.442505] EXT4-fs (sda1): unmounting filesystem. [ 53.463705] sd 0:0:0:0: [sda] Spinning up disk... [ 54.483278] .ready [ 54.520392] sda: sda1 sda2 [ 54.587326] sd 0:0:0:0: [sda] Synchronizing SCSI cache [ 54.812780] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1) [ 54.813935] scsi host0: scsi_debug: version 0191 [20210520] [ 54.813935] dev_size_mb=50, opts=0x0, submit_queues=1, statistics=0 [ 54.814996] scsi 0:0:0:0: Direct-Access Linux scsi_debug 0191 PQ: 0 ANSI: 7 [ 54.826577] sd 0:0:0:0: Power-on or device reset occurred [ 54.840018] sd 0:0:0:0: [sda] 102400 512-byte logical blocks: (52.4 MB/50.0 MiB) [ 54.840784] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 54.845234] sd 0:0:0:0: [sda] Write Protect is off [ 54.853788] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA [ 54.866622] sd 0:0:0:0: [sda] Preferred minimum I/O size 4096 bytes [ 54.867488] sd 0:0:0:0: [sda] Optimal transfer size 524288 bytes [ 54.904781] sd 0:0:0:0: [sda] Attached SCSI disk [ 55.821704] sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 > [ 55.947353] sd 0:0:0:0: [sda] Synchronizing SCSI cache [ 56.121954] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1) [ 56.123083] scsi host0: scsi_debug: version 0191 [20210520] [ 56.123083] dev_size_mb=50, opts=0x0, submit_queues=1, statistics=0 [ 56.124134] scsi 0:0:0:0: Direct-Access Linux scsi_debug 0191 PQ: 0 ANSI: 7 [ 56.125104] sd 0:0:0:0: Power-on or device reset occurred [ 56.133649] sd 0:0:0:0: [sda] physical block alignment offset: 3584 [ 56.134255] sd 0:0:0:0: [sda] 102400 512-byte logical blocks: (52.4 MB/50.0 MiB) [ 56.134829] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 56.139371] sd 0:0:0:0: [sda] Write Protect is off [ 56.147847] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA [ 56.160793] sd 0:0:0:0: [sda] Preferred minimum I/O size 4096 bytes [ 56.161374] sd 0:0:0:0: [sda] Optimal transfer size 524288 bytes [ 56.198652] sd 0:0:0:0: [sda] Attached SCSI disk [ 57.151018] sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 > [ 57.271366] sd 0:0:0:0: [sda] Synchronizing SCSI cache [ 57.434288] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1) [ 57.435309] scsi host0: scsi_debug: version 0191 [20210520] [ 57.435309] dev_size_mb=50, opts=0x0, submit_queues=1, statistics=0 [ 57.436546] scsi 0:0:0:0: Direct-Access Linux scsi_debug 0191 PQ: 0 ANSI: 7 [ 57.437470] sd 0:0:0:0: Power-on or device reset occurred [ 57.446107] sd 0:0:0:0: [sda] 102400 512-byte logical blocks: (52.4 MB/50.0 MiB) [ 57.446864] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 57.451368] sd 0:0:0:0: [sda] Write Protect is off [ 57.459874] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA [ 57.472723] sd 0:0:0:0: [sda] Preferred minimum I/O size 4096 bytes [ 57.473592] sd 0:0:0:0: [sda] Optimal transfer size 524288 bytes [ 57.510817] sd 0:0:0:0: [sda] Attached SCSI disk [ 57.933226] sda: sda1 sda2 [ 58.147404] sd 0:0:0:0: [sda] Synchronizing SCSI cache [ 58.323084] loop0: detected capacity change from 0 to 102400 [ 58.449563] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1) [ 58.455500] scsi host0: scsi_debug: version 0191 [20210520] [ 58.455500] dev_size_mb=50, opts=0x0, submit_queues=1, statistics=0 [ 58.456750] scsi 0:0:0:0: Direct-Access Linux scsi_debug 0191 PQ: 0 ANSI: 7 [ 58.457579] sd 0:0:0:0: Power-on or device reset occurred [ 58.466345] sd 0:0:0:0: [sda] 102400 512-byte logical blocks: (52.4 MB/50.0 MiB) [ 58.471228] sd 0:0:0:0: [sda] Write Protect is off [ 58.480038] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA [ 58.493016] sd 0:0:0:0: [sda] Preferred minimum I/O size 512 bytes [ 58.493807] sd 0:0:0:0: [sda] Optimal transfer size 524288 bytes [ 58.531045] sd 0:0:0:0: [sda] Attached SCSI disk [ 59.444254] sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 > [ 59.543354] sd 0:0:0:0: [sda] Synchronizing SCSI cache [ 60.331719] loop0: detected capacity change from 0 to 20480 [ 60.374495] loop0: detected capacity change from 20480 to 40960 [ 64.942717] loop0: detected capacity change from 0 to 10240 [ 65.040311] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 65.042525] EXT4-fs (loop0): mounted filesystem without journal. Quota mode: disabled. [ 65.057223] EXT4-fs (loop0): unmounting filesystem. [ 66.234194] NET: Registered PF_ALG protocol family [ 69.873896] loop0: detected capacity change from 0 to 20480 [ 69.876356] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 69.878253] EXT4-fs (loop0): mounted filesystem without journal. Quota mode: disabled. [ 69.880905] EXT4-fs (loop0): unmounting filesystem. [ 69.901196] loop0: detected capacity change from 0 to 20480 [ 69.903296] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 69.905030] EXT4-fs (loop0): mounted filesystem without journal. Quota mode: disabled. [ 69.907634] EXT4-fs (loop0): unmounting filesystem. [ 69.926964] loop0: detected capacity change from 0 to 20480 [ 69.930376] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 69.939468] EXT4-fs (loop0): mounted filesystem without journal. Quota mode: disabled. [ 69.954313] EXT4-fs (loop0): unmounting filesystem. [ 69.995393] loop0: detected capacity change from 0 to 20480 [ 69.997263] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 69.999049] EXT4-fs (loop0): mounted filesystem without journal. Quota mode: disabled. [ 70.004033] EXT4-fs (loop0): unmounting filesystem. [ 70.023301] loop0: detected capacity change from 0 to 20480 [ 70.027616] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 70.029446] EXT4-fs (loop0): mounted filesystem without journal. Quota mode: disabled. [ 70.034488] EXT4-fs (loop0): unmounting filesystem. [ 70.088958] loop0: detected capacity change from 0 to 20478 [ 70.136531] loop0: detected capacity change from 0 to 20480 [ 70.185990] loop0: detected capacity change from 0 to 20480 [ 70.310680] loop0: detected capacity change from 0 to 20480 [ 70.312248] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 70.317349] EXT4-fs (loop0): mounted filesystem without journal. Quota mode: disabled. [ 70.322388] EXT4-fs (loop0): unmounting filesystem. [ 70.325670] loop0: detected capacity change from 0 to 10240 [ 70.327381] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 70.328971] EXT4-fs (loop0): mounted filesystem without journal. Quota mode: disabled. [ 70.331579] loop1: detected capacity change from 0 to 10240 [ 70.332700] EXT4-fs (loop1): mounting ext2 file system using the ext4 subsystem [ 70.334237] EXT4-fs (loop1): mounted filesystem without journal. Quota mode: disabled. [ 70.336682] EXT4-fs (loop0): unmounting filesystem. [ 70.339697] EXT4-fs (loop1): unmounting filesystem. [ 70.342652] loop0: detected capacity change from 0 to 10240 [ 75.578108] loop0: detected capacity change from 0 to 20480 [ 75.626119] loop0: detected capacity change from 0 to 18432 [ 75.664959] loop0: detected capacity change from 0 to 6144 [ 75.715908] loop0: detected capacity change from 0 to 6144 [ 75.904875] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1) [ 75.908282] scsi host0: scsi_debug: version 0191 [20210520] [ 75.908282] dev_size_mb=11, opts=0x0, submit_queues=1, statistics=0 [ 75.918213] scsi 0:0:0:0: Direct-Access Linux scsi_debug 0191 PQ: 0 ANSI: 7 [ 75.919053] sd 0:0:0:0: Power-on or device reset occurred [ 75.932131] sd 0:0:0:0: [sda] 22528 512-byte logical blocks: (11.5 MB/11.0 MiB) [ 75.936989] sd 0:0:0:0: [sda] Write Protect is off [ 75.945447] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA [ 75.958274] sd 0:0:0:0: [sda] Preferred minimum I/O size 512 bytes [ 75.959188] sd 0:0:0:0: [sda] Optimal transfer size 524288 bytes [ 75.996243] sd 0:0:0:0: [sda] Attached SCSI disk [ 76.010999] loop0: detected capacity change from 0 to 22528 [ 76.063901] loop0: detected capacity change from 0 to 20480 [ 76.111394] loop0: detected capacity change from 0 to 6144 [ 76.155925] loop0: detected capacity change from 0 to 6144 [ 76.251340] sd 0:0:0:0: [sda] Synchronizing SCSI cache [ 76.384588] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1) [ 76.385866] scsi host0: scsi_debug: version 0191 [20210520] [ 76.385866] dev_size_mb=11, opts=0x0, submit_queues=1, statistics=0 [ 76.386880] scsi 0:0:0:0: Direct-Access Linux scsi_debug 0191 PQ: 0 ANSI: 7 [ 76.387782] sd 0:0:0:0: Power-on or device reset occurred [ 76.397115] sd 0:0:0:0: [sda] 22528 512-byte logical blocks: (11.5 MB/11.0 MiB) [ 76.401874] sd 0:0:0:0: [sda] Write Protect is off [ 76.410706] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA [ 76.428734] sd 0:0:0:0: [sda] Preferred minimum I/O size 512 bytes [ 76.429471] sd 0:0:0:0: [sda] Optimal transfer size 524288 bytes [ 76.466914] sd 0:0:0:0: [sda] Attached SCSI disk [ 76.481432] loop0: detected capacity change from 0 to 22528 [ 76.509119] loop0: detected capacity change from 0 to 22528 [ 76.567075] loop0: detected capacity change from 0 to 22528 [ 76.639455] loop0: detected capacity change from 0 to 2048 [ 76.642082] loop1: detected capacity change from 0 to 2048 [ 76.710864] loop0: detected capacity change from 0 to 4096 [ 76.763505] loop0: detected capacity change from 0 to 20480 [ 76.819202] loop0: detected capacity change from 0 to 22528 [ 76.872743] loop0: detected capacity change from 0 to 2048 [ 76.875028] loop1: detected capacity change from 0 to 18432 [ 76.928562] loop0: detected capacity change from 0 to 22528 [ 77.098081] loop0: detected capacity change from 0 to 22528 [ 77.211332] sd 0:0:0:0: [sda] Synchronizing SCSI cache [ 79.928398] loop0: detected capacity change from 0 to 10240 [ 85.866816] loop0: detected capacity change from 0 to 10240 [ 85.909610] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 85.911494] EXT4-fs (loop0): mounted filesystem without journal. Quota mode: disabled. [ 85.919930] EXT4-fs (loop0): unmounting filesystem. [ 86.049878] loop0: detected capacity change from 0 to 10240 [ 86.064215] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 86.066229] EXT4-fs (loop0): mounted filesystem without journal. Quota mode: disabled. [ 86.073017] EXT4-fs (loop0): unmounting filesystem. [ 86.098154] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 86.100086] EXT4-fs (loop0): mounted filesystem without journal. Quota mode: disabled. [ 86.111831] EXT4-fs (loop0): unmounting filesystem. [ 86.163885] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 86.167918] EXT4-fs (loop0): mounted filesystem without journal. Quota mode: disabled. [ 86.193322] EXT4-fs (loop0): unmounting filesystem. [ 86.218126] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 86.220678] EXT4-fs (loop0): mounted filesystem without journal. Quota mode: disabled. [ 86.227946] EXT4-fs (loop0): unmounting filesystem. [ 86.390543] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1) [ 86.391533] scsi host0: scsi_debug: version 0191 [20210520] [ 86.391533] dev_size_mb=50, opts=0x0, submit_queues=1, statistics=0 [ 86.397584] scsi 0:0:0:0: Direct-Access Linux scsi_debug 0191 PQ: 0 ANSI: 7 [ 86.398487] sd 0:0:0:0: Power-on or device reset occurred [ 86.411224] sd 0:0:0:0: [sda] 102400 512-byte logical blocks: (52.4 MB/50.0 MiB) [ 86.420782] sd 0:0:0:0: [sda] Write Protect is off [ 86.429306] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA [ 86.446747] sd 0:0:0:0: [sda] Preferred minimum I/O size 512 bytes [ 86.447346] sd 0:0:0:0: [sda] Optimal transfer size 524288 bytes [ 86.484549] sd 0:0:0:0: [sda] Attached SCSI disk [ 87.243500] sda: sda1 sda2 sda3 sda4 [ 88.189925] EXT4-fs (sda1): mounting ext2 file system using the ext4 subsystem [ 88.203689] EXT4-fs (sda1): mounted filesystem without journal. Quota mode: disabled. [ 88.208634] EXT4-fs (sda2): mounting ext2 file system using the ext4 subsystem [ 88.221766] EXT4-fs (sda2): mounted filesystem without journal. Quota mode: disabled. [ 88.226970] EXT4-fs (sda3): mounting ext2 file system using the ext4 subsystem [ 88.236208] EXT4-fs (sda3): mounted filesystem without journal. Quota mode: disabled. [ 88.388586] EXT4-fs (sda4): mounted filesystem with ordered data mode. Quota mode: disabled. [ 88.532001] EXT4-fs (sda1): unmounting filesystem. [ 88.592564] EXT4-fs (sda2): unmounting filesystem. [ 88.597533] EXT4-fs (sda3): unmounting filesystem. [ 88.646332] EXT4-fs (sda4): unmounting filesystem. [ 88.825395] EXT4-fs (sda4): mounted filesystem with ordered data mode. Quota mode: disabled. [ 88.878690] EXT4-fs (sda4): unmounting filesystem. [ 88.904966] EXT4-fs (sda1): mounting ext2 file system using the ext4 subsystem [ 88.918515] EXT4-fs (sda1): mounted filesystem without journal. Quota mode: disabled. [ 88.923500] EXT4-fs (sda2): mounting ext2 file system using the ext4 subsystem [ 88.936855] EXT4-fs (sda2): mounted filesystem without journal. Quota mode: disabled. [ 88.941853] EXT4-fs (sda3): mounting ext2 file system using the ext4 subsystem [ 88.951032] EXT4-fs (sda3): mounted filesystem without journal. Quota mode: disabled. [ 89.006861] EXT4-fs (sda1): unmounting filesystem. [ 89.060131] EXT4-fs (sda2): unmounting filesystem. [ 89.065047] EXT4-fs (sda3): unmounting filesystem. [ 89.085681] EXT4-fs (sda3): mounting ext2 file system using the ext4 subsystem [ 89.094858] EXT4-fs (sda3): mounted filesystem without journal. Quota mode: disabled. [ 89.099904] EXT4-fs (sda3): unmounting filesystem. [ 89.122712] EXT4-fs (sda1): mounting ext2 file system using the ext4 subsystem [ 89.131913] EXT4-fs (sda1): mounted filesystem without journal. Quota mode: disabled. [ 89.136829] EXT4-fs (sda2): mounting ext2 file system using the ext4 subsystem [ 89.145961] EXT4-fs (sda2): mounted filesystem without journal. Quota mode: disabled. [ 89.150887] EXT4-fs (sda3): mounting ext2 file system using the ext4 subsystem [ 89.159977] EXT4-fs (sda3): mounted filesystem without journal. Quota mode: disabled. [ 89.307626] EXT4-fs (sda4): orphan cleanup on readonly fs [ 89.308335] EXT4-fs (sda4): mounted filesystem with ordered data mode. Quota mode: disabled. [ 89.313186] EXT4-fs (sda1): unmounting filesystem. [ 89.314153] EXT4-fs (sda2): unmounting filesystem. [ 89.314778] EXT4-fs (sda3): unmounting filesystem. [ 89.315383] EXT4-fs (sda4): unmounting filesystem. [ 89.338978] EXT4-fs (sda1): mounting ext2 file system using the ext4 subsystem [ 89.352203] EXT4-fs (sda1): mounted filesystem without journal. Quota mode: disabled. [ 89.357281] EXT4-fs (sda2): mounting ext2 file system using the ext4 subsystem [ 89.370542] EXT4-fs (sda2): mounted filesystem without journal. Quota mode: disabled. [ 89.375552] EXT4-fs (sda3): mounting ext2 file system using the ext4 subsystem [ 89.388642] EXT4-fs (sda3): mounted filesystem without journal. Quota mode: disabled. [ 89.540637] EXT4-fs (sda4): mounted filesystem with ordered data mode. Quota mode: disabled. [ 89.594019] EXT4-fs (sda1): unmounting filesystem. [ 89.647649] EXT4-fs (sda2): unmounting filesystem. [ 89.700812] EXT4-fs (sda3): unmounting filesystem. [ 89.754075] EXT4-fs (sda4): unmounting filesystem. [ 89.827407] sd 0:0:0:0: [sda] Synchronizing SCSI cache [ 90.130026] loop0: detected capacity change from 0 to 102400 [ 90.183240] BTRFS: device fsid d50dcd2b-c26b-4116-893a-3f4db34d15ee devid 1 transid 6 /dev/loop0 scanned by mkfs.btrfs (21021) [ 90.186570] loop1: detected capacity change from 0 to 102400 [ 90.191436] BTRFS info (device loop1): using crc32c (crc32c-generic) checksum algorithm [ 90.192162] BTRFS info (device loop1): using free space tree [ 90.194578] BTRFS info (device loop1): enabling ssd optimizations [ 90.195455] BTRFS info (device loop1): checking UUID tree [ 90.212628] BTRFS info (device loop1): setting incompat feature flag for DEFAULT_SUBVOL (0x2) [ 90.256370] BTRFS: device fsid d50dcd2b-c26b-4116-893a-3f4db34d15ee devid 1 transid 11 /dev/loop0 scanned by mount (21067) [ 90.257582] BTRFS info (device loop0): using crc32c (crc32c-generic) checksum algorithm [ 90.258424] BTRFS info (device loop0): using free space tree [ 90.319894] BTRFS: device fsid d50dcd2b-c26b-4116-893a-3f4db34d15ee devid 1 transid 12 /dev/loop0 scanned by mount (21111) [ 90.321206] BTRFS info (device loop0): using crc32c (crc32c-generic) checksum algorithm [ 90.321945] BTRFS info (device loop0): using free space tree [ 90.470365] loop0: detected capacity change from 0 to 10240 [ 90.510259] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 90.512700] EXT4-fs (loop0): mounted filesystem without journal. Quota mode: disabled. [ 90.519819] EXT4-fs (loop0): unmounting filesystem. [ 90.537557] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 90.539625] EXT4-fs (loop0): mounted filesystem without journal. Quota mode: disabled. [ 90.548766] EXT4-fs (loop0): unmounting filesystem. [ 90.655972] loop0: detected capacity change from 0 to 10240 [ 90.689219] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 90.691718] EXT4-fs (loop0): mounted filesystem without journal. Quota mode: disabled. [ 90.701897] EXT4-fs (loop0): unmounting filesystem. [ 90.848645] loop0: detected capacity change from 0 to 10240 [ 90.964876] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 90.966928] EXT4-fs (loop0): mounted filesystem without journal. Quota mode: disabled. [ 90.977420] EXT4-fs (loop0): unmounting filesystem. [ 91.073626] loop0: detected capacity change from 0 to 10240 [ 91.110069] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 91.112153] EXT4-fs (loop0): mounted filesystem without journal. Quota mode: disabled. [ 91.119872] EXT4-fs (loop0): unmounting filesystem. [ 91.148755] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 91.156265] EXT4-fs (loop0): mounted filesystem without journal. Quota mode: disabled. [ 91.163707] EXT4-fs (loop0): unmounting filesystem. [ 91.183128] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 91.186797] EXT4-fs (loop0): mounted filesystem without journal. Quota mode: disabled. [ 91.194212] EXT4-fs (loop0): unmounting filesystem. [ 91.332713] loop0: detected capacity change from 0 to 10240 [ 91.386497] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 91.412316] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 91.566739] loop0: detected capacity change from 0 to 10240 [ 91.605164] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 91.639122] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 91.808783] loop0: detected capacity change from 0 to 10240 [ 91.809654] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 92.048151] loop0: detected capacity change from 0 to 10240 [ 92.074040] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 92.201887] loop0: detected capacity change from 0 to 10240 [ 92.261628] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 92.291935] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 92.319448] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 92.442213] loop0: detected capacity change from 0 to 10240 [ 92.475022] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 92.508020] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 92.618873] loop0: detected capacity change from 0 to 10240 [ 92.656115] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 92.681831] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 92.790484] loop0: detected capacity change from 0 to 10240 [ 92.818165] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 92.844922] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 93.087572] loop0: detected capacity change from 0 to 10240 [ 93.089010] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 93.168678] loop0: detected capacity change from 0 to 10240 [ 93.179803] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 93.187322] EXT4-fs (loop0): re-mounted. Quota mode: disabled. [ 93.404452] loop0: detected capacity change from 0 to 10240 [ 93.424046] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 93.447839] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 93.768940] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1) [ 93.770028] scsi host0: scsi_debug: version 0191 [20210520] [ 93.770028] dev_size_mb=50, opts=0x0, submit_queues=1, statistics=0 [ 93.786075] scsi 0:0:0:0: Direct-Access Linux scsi_debug 0191 PQ: 0 ANSI: 7 [ 93.787023] sd 0:0:0:0: Power-on or device reset occurred [ 93.820541] sd 0:0:0:0: [sda] 102400 512-byte logical blocks: (52.4 MB/50.0 MiB) [ 93.842155] sd 0:0:0:0: [sda] Write Protect is off [ 93.850791] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA [ 93.863662] sd 0:0:0:0: [sda] Preferred minimum I/O size 512 bytes [ 93.864414] sd 0:0:0:0: [sda] Optimal transfer size 524288 bytes [ 93.901894] sd 0:0:0:0: [sda] Attached SCSI disk [ 94.620837] sda: sda1 sda2 sda3 sda4 [ 95.594275] EXT4-fs (sda1): mounting ext2 file system using the ext4 subsystem [ 95.876719] EXT4-fs (sda1): mounting ext2 file system using the ext4 subsystem [ 96.139391] EXT4-fs (sda1): mounting ext2 file system using the ext4 subsystem [ 96.345324] EXT4-fs (sda2): mounting ext2 file system using the ext4 subsystem [ 96.456328] EXT4-fs (sda3): mounting ext2 file system using the ext4 subsystem [ 96.555570] EXT4-fs (sda4): mounting ext2 file system using the ext4 subsystem [ 96.855406] sd 0:0:0:0: [sda] Synchronizing SCSI cache [ 97.097170] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1) [ 97.098145] scsi host0: scsi_debug: version 0191 [20210520] [ 97.098145] dev_size_mb=50, opts=0x0, submit_queues=1, statistics=0 [ 97.105263] scsi 0:0:0:0: Direct-Access Linux scsi_debug 0191 PQ: 0 ANSI: 7 [ 97.106453] sd 0:0:0:0: Power-on or device reset occurred [ 97.115325] sd 0:0:0:0: [sda] 102400 512-byte logical blocks: (52.4 MB/50.0 MiB) [ 97.120362] sd 0:0:0:0: [sda] Write Protect is off [ 97.128964] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA [ 97.141845] sd 0:0:0:0: [sda] Preferred minimum I/O size 512 bytes [ 97.142631] sd 0:0:0:0: [sda] Optimal transfer size 524288 bytes [ 97.179953] sd 0:0:0:0: [sda] Attached SCSI disk [ 98.011507] sda: sda1 sda2 sda3 sda4 [ 98.979277] EXT4-fs (sda1): mounting ext2 file system using the ext4 subsystem [ 99.099758] EXT4-fs (sda2): mounting ext2 file system using the ext4 subsystem [ 99.228765] EXT4-fs (sda3): mounting ext2 file system using the ext4 subsystem [ 99.340918] EXT4-fs (sda4): mounting ext2 file system using the ext4 subsystem [ 99.655342] sd 0:0:0:0: [sda] Synchronizing SCSI cache [ 99.854005] loop0: detected capacity change from 0 to 10240 [ 99.910273] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 99.970852] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 100.296380] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1) [ 100.303299] scsi host0: scsi_debug: version 0191 [20210520] [ 100.303299] dev_size_mb=50, opts=0x0, submit_queues=1, statistics=0 [ 100.311459] scsi 0:0:0:0: Direct-Access Linux scsi_debug 0191 PQ: 0 ANSI: 7 [ 100.312322] sd 0:0:0:0: Power-on or device reset occurred [ 100.327381] sd 0:0:0:0: [sda] 102400 512-byte logical blocks: (52.4 MB/50.0 MiB) [ 100.339904] sd 0:0:0:0: [sda] Write Protect is off [ 100.348600] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA [ 100.361743] sd 0:0:0:0: [sda] Preferred minimum I/O size 512 bytes [ 100.362651] sd 0:0:0:0: [sda] Optimal transfer size 524288 bytes [ 100.408374] sd 0:0:0:0: [sda] Attached SCSI disk [ 101.211871] sda: sda1 sda2 sda3 [ 101.535331] sd 0:0:0:0: [sda] Synchronizing SCSI cache [ 131.908563] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1) [ 131.909668] scsi host0: scsi_debug: version 0191 [20210520] [ 131.909668] dev_size_mb=50, opts=0x0, submit_queues=1, statistics=0 [ 131.925324] scsi 0:0:0:0: Direct-Access Linux scsi_debug 0191 PQ: 0 ANSI: 7 [ 131.926296] sd 0:0:0:0: Power-on or device reset occurred [ 131.948314] sd 0:0:0:0: [sda] 102400 512-byte logical blocks: (52.4 MB/50.0 MiB) [ 131.949062] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 131.963547] sd 0:0:0:0: [sda] Write Protect is off [ 131.972076] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA [ 131.989912] sd 0:0:0:0: [sda] Preferred minimum I/O size 4096 bytes [ 131.990458] sd 0:0:0:0: [sda] Optimal transfer size 524288 bytes [ 132.027630] sd 0:0:0:0: [sda] Attached SCSI disk [ 133.144678] sda: sda1 sda2 sda3 sda4 < sda5 sda6 > [ 133.668941] sda: sda1 sda2 sda3 sda4 < sda5 sda6 > [ 135.078504] sda: sda1 sda2 sda3 [ 136.141740] sda: sda1 [ 137.647502] sda: sda1 sda2 sda3 sda4 < sda5 sda6 > [ 139.185555] sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 > [ 140.289867] sda: sda1 [ 140.760561] sda: sda1 [ 141.898211] sda: sda1 sda2 < > [ 142.371192] sda: sda1 sda2 < > [ 143.513809] sda: sda1 sda2 < > [ 143.991616] sda: sda1 sda2 < > [ 145.325369] sda: sda1 sda2 sda3 sda4 < sda5 sda6 > [ 145.827873] sda: sda1 sda2 sda3 sda4 < sda5 sda6 > [ 147.199214] sda: sda1 sda2 sda3 sda4 < sda5 sda6 > [ 147.709079] sda: sda1 sda2 sda3 sda4 < sda5 sda6 > [ 148.822525] sda: sda1 [ 150.024151] sda: sda1 sda3 [ 151.243819] sda: sda1 sda2 [ 152.876058] sda: sda1 sda2 sda3 sda4 [ 154.107223] sda: sda1 sda2 sda3 [ 154.279340] sd 0:0:0:0: [sda] Synchronizing SCSI cache [ 154.469335] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1) [ 154.470310] scsi host0: scsi_debug: version 0191 [20210520] [ 154.470310] dev_size_mb=100, opts=0x0, submit_queues=1, statistics=0 [ 154.477736] scsi 0:0:0:0: Direct-Access Linux scsi_debug 0191 PQ: 0 ANSI: 7 [ 154.478625] sd 0:0:0:0: Power-on or device reset occurred [ 154.493531] sd 0:0:0:0: [sda] 204800 512-byte logical blocks: (105 MB/100 MiB) [ 154.494141] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 154.498609] sd 0:0:0:0: [sda] Write Protect is off [ 154.507112] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA [ 154.519934] sd 0:0:0:0: [sda] Preferred minimum I/O size 4096 bytes [ 154.520498] sd 0:0:0:0: [sda] Optimal transfer size 524288 bytes [ 154.557831] sd 0:0:0:0: [sda] Attached SCSI disk [ 155.873526] sda: sda1 sda2 sda3 sda4 [ 157.647819] sda: sda1 sda2 sda3 sda4 [ 159.559154] sda: sda1 sda2 sda3 sda4 [ 159.643324] sd 0:0:0:0: [sda] Synchronizing SCSI cache [ 159.786294] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1) [ 159.787362] scsi host0: scsi_debug: version 0191 [20210520] [ 159.787362] dev_size_mb=50, opts=0x0, submit_queues=1, statistics=0 [ 159.788409] scsi 0:0:0:0: Direct-Access Linux scsi_debug 0191 PQ: 0 ANSI: 7 [ 159.789225] sd 0:0:0:0: Power-on or device reset occurred [ 159.797823] sd 0:0:0:0: [sda] 102400 512-byte logical blocks: (52.4 MB/50.0 MiB) [ 159.798400] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 159.802853] sd 0:0:0:0: [sda] Write Protect is off [ 159.811327] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA [ 159.824060] sd 0:0:0:0: [sda] Preferred minimum I/O size 4096 bytes [ 159.824572] sd 0:0:0:0: [sda] Optimal transfer size 524288 bytes [ 159.861747] sd 0:0:0:0: [sda] Attached SCSI disk [ 161.234970] sda: sda1 sda2 sda3 sda4 sda5 [ 161.992249] sda: sda1 sda2 sda3 sda4 sda5 [ 162.713112] sda: sda1 sda2 sda3 sda4 sda5 [ 163.427902] sda: sda1 sda2 sda3 sda4 sda5 [ 164.141762] sda: sda1 sda2 sda3 sda4 sda5 [ 164.855446] sda: sda1 sda2 sda3 sda4 sda5 [ 165.824081] sda: sda1 sda2 sda3 sda4 sda5 [ 166.686549] sda: sda1 sda2 sda3 sda4 sda5 [ 167.552697] sda: sda1 sda2 sda3 sda4 sda5 [ 168.558543] sda: sda1 sda2 sda3 sda4 sda5 [ 169.559960] sda: sda1 sda2 sda3 sda4 sda5 [ 170.593115] sda: sda1 sda2 sda3 sda4 sda5 [ 173.233960] sda: sda1 sda2 sda3 sda4 [ 175.110200] sda: sda1 [ 175.841579] sda: sda1 [ 177.648462] sda: sda1 sda2 sda3 sda4 [ 178.377269] sda: sda1 sda2 sda3 sda4 [ 178.495390] sd 0:0:0:0: [sda] Synchronizing SCSI cache [ 178.713884] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1) [ 178.714878] scsi host0: scsi_debug: version 0191 [20210520] [ 178.714878] dev_size_mb=100, opts=0x0, submit_queues=1, statistics=0 [ 178.720644] scsi 0:0:0:0: Direct-Access Linux scsi_debug 0191 PQ: 0 ANSI: 7 [ 178.721517] sd 0:0:0:0: Power-on or device reset occurred [ 178.730175] sd 0:0:0:0: [sda] 204800 512-byte logical blocks: (105 MB/100 MiB) [ 178.734827] sd 0:0:0:0: [sda] Write Protect is off [ 178.743361] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA [ 178.756102] sd 0:0:0:0: [sda] Preferred minimum I/O size 512 bytes [ 178.756673] sd 0:0:0:0: [sda] Optimal transfer size 524288 bytes [ 178.793952] sd 0:0:0:0: [sda] Attached SCSI disk [ 179.347690] sda: sda1 [ 180.230832] sda: sda1 [ 180.810145] sda: sda1 [ 181.458199] sda: sda1 [ 181.631372] sd 0:0:0:0: [sda] Synchronizing SCSI cache [ 181.811668] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1) [ 181.812600] scsi host0: scsi_debug: version 0191 [20210520] [ 181.812600] dev_size_mb=100, opts=0x0, submit_queues=1, statistics=0 [ 181.818080] scsi 0:0:0:0: Direct-Access Linux scsi_debug 0191 PQ: 0 ANSI: 7 [ 181.818885] sd 0:0:0:0: Power-on or device reset occurred [ 181.827482] sd 0:0:0:0: [sda] 204800 512-byte logical blocks: (105 MB/100 MiB) [ 181.832133] sd 0:0:0:0: [sda] Write Protect is off [ 181.840721] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA [ 181.853493] sd 0:0:0:0: [sda] Preferred minimum I/O size 512 bytes [ 181.854362] sd 0:0:0:0: [sda] Optimal transfer size 524288 bytes [ 181.891628] sd 0:0:0:0: [sda] Attached SCSI disk [ 182.590175] sda: sda1 [ 183.082071] sda: sda1 [ 183.581211] sda: sda1 [ 184.078654] sda: sda1 [ 184.574200] sda: sda1 [ 185.070633] sda: sda1 [ 185.565361] sda: sda1 [ 186.060723] sda: sda1 [ 186.559461] sda: sda1 [ 187.055500] sda: sda1 [ 187.566999] sda: sda1 [ 188.059789] sda: sda1 [ 188.550074] sda: sda1 [ 189.172263] sda: sda1 sda2 [ 189.775230] sda: sda1 sda2 sda3 [ 190.258739] sda: sda1 sda2 sda3 [ 190.760232] sda: sda1 sda2 sda3 [ 192.154925] sda: sda1 [ 192.887125] sda: sda1 [ 193.642815] sda: sda1 [ 194.520317] sda: sda1 [ 195.356295] sda: sda1 [ 196.097722] sda: sda1 [ 196.842119] sda: sda1 [ 197.582700] sda: sda1 [ 198.323037] sda: sda1 [ 199.178599] sda: sda1 [ 199.917665] sda: sda1 [ 200.658303] sda: sda1 [ 201.398562] sda: sda1 [ 202.291413] sda: sda1 sda2 [ 203.145583] sda: sda1 sda2 sda3 [ 203.889024] sda: sda1 sda2 sda3 [ 204.645786] sda: sda1 sda2 sda3 [ 206.103536] sda: sda1 sda2 sda3 < sda5 sda6 > sda4 [ 206.601267] sda: sda1 sda2 sda3 < sda5 sda6 > sda4 [ 206.723321] sd 0:0:0:0: [sda] Synchronizing SCSI cache [ 206.883742] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1) [ 206.889802] scsi host0: scsi_debug: version 0191 [20210520] [ 206.889802] dev_size_mb=50, opts=0x0, submit_queues=1, statistics=0 [ 206.895618] scsi 0:0:0:0: Direct-Access Linux scsi_debug 0191 PQ: 0 ANSI: 7 [ 206.896621] sd 0:0:0:0: Power-on or device reset occurred [ 206.911542] sd 0:0:0:0: [sda] 102400 512-byte logical blocks: (52.4 MB/50.0 MiB) [ 206.912305] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 206.916895] sd 0:0:0:0: [sda] Write Protect is off [ 206.925770] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA [ 206.945216] sd 0:0:0:0: [sda] Preferred minimum I/O size 4096 bytes [ 206.946000] sd 0:0:0:0: [sda] Optimal transfer size 524288 bytes [ 206.983365] sd 0:0:0:0: [sda] Attached SCSI disk [ 208.318024] sda: sda1 sda2 sda3 sda4 [ 210.103673] sda: sda1 sda2 sda3 sda4 [ 211.896823] sda: sda1 sda2 sda3 sda4 [ 213.787327] sd 0:0:0:0: [sda] Synchronizing SCSI cache [ 214.192838] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1) [ 214.202146] scsi host0: scsi_debug: version 0191 [20210520] [ 214.202146] dev_size_mb=50, opts=0x0, submit_queues=1, statistics=0 [ 214.211770] scsi 0:0:0:0: Direct-Access Linux scsi_debug 0191 PQ: 0 ANSI: 7 [ 214.212963] sd 0:0:0:0: Power-on or device reset occurred [ 214.230103] sd 0:0:0:0: [sda] 102400 512-byte logical blocks: (52.4 MB/50.0 MiB) [ 214.230969] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 214.235611] sd 0:0:0:0: [sda] Write Protect is off [ 214.244715] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA [ 214.258681] sd 0:0:0:0: [sda] Preferred minimum I/O size 4096 bytes [ 214.259478] sd 0:0:0:0: [sda] Optimal transfer size 524288 bytes [ 214.298483] sd 0:0:0:0: [sda] Attached SCSI disk [ 219.270514] sda: sda1 [ 220.993468] sda: sda1 [ 221.323325] sd 0:0:0:0: [sda] Synchronizing SCSI cache [ 221.524160] loop0: detected capacity change from 0 to 10240 [ 221.540480] Adding 5116k swap on /dev/loop0. Priority:-2 extents:1 across:5116k [ 221.657215] loop0: detected capacity change from 0 to 10240 [ 221.680378] Adding 5116k swap on /dev/loop0. Priority:-2 extents:1 across:5116k [ 221.796039] loop0: detected capacity change from 0 to 10240 [ 221.813273] Adding 5116k swap on /dev/loop0. Priority:-2 extents:1 across:5116k [ 221.944581] loop0: detected capacity change from 0 to 10240 [ 221.967123] Adding 5116k swap on /dev/loop0. Priority:-2 extents:1 across:5116k [ 222.102356] loop0: detected capacity change from 0 to 10240 [ 222.162588] Adding 5116k swap on /dev/loop0. Priority:-2 extents:1 across:5116k [ 223.653785] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1) [ 223.659937] scsi host0: scsi_debug: version 0191 [20210520] [ 223.659937] dev_size_mb=50, opts=0x0, submit_queues=1, statistics=0 [ 223.666163] scsi 0:0:0:0: Direct-Access Linux scsi_debug 0191 PQ: 0 ANSI: 7 [ 223.669688] sd 0:0:0:0: Power-on or device reset occurred [ 223.683380] sd 0:0:0:0: [sda] 102400 512-byte logical blocks: (52.4 MB/50.0 MiB) [ 223.693197] sd 0:0:0:0: [sda] Write Protect is off [ 223.720196] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA [ 223.733125] sd 0:0:0:0: [sda] Preferred minimum I/O size 512 bytes [ 223.733664] sd 0:0:0:0: [sda] Optimal transfer size 524288 bytes [ 223.770799] sda: sda1 sda2 [ 223.771327] sd 0:0:0:0: [sda] Attached SCSI disk [ 224.791332] sd 0:0:0:0: [sda] Synchronizing SCSI cache [ 224.894147] udevd[29551]: starting version 3.2.11 [ 224.896594] udevd[29552]: starting eudev-3.2.11