[ 0.000000] Linux version 5.15.103-yocto-standard (oe-user@oe-host) (mips-poky-linux-gcc (GCC) 11.3.0, GNU ld (GNU Binutils) 2.38.20220708) #1 SMP PREEMPT Sat Mar 18 03:05:00 UTC 2023 [ 0.000000] earlycon: uart8250 at I/O port 0x3f8 (options '38400n8') [ 0.000000] printk: bootconsole [uart8250] enabled [ 0.000000] CPU0 revision is: 00019500 (MIPS 34Kc) [ 0.000000] FPU revision is: 00739500 [ 0.000000] OF: fdt: No chosen node found, continuing without [ 0.000000] MIPS: machine is mti,malta [ 0.000000] Software DMA cache coherency enabled [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Primary instruction cache 2kB, VIPT, 2-way, linesize 16 bytes. [ 0.000000] Primary data cache 2kB, 2-way, VIPT, no aliases, linesize 16 bytes [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000000000000-0x0000000000ffffff] [ 0.000000] Normal [mem 0x0000000001000000-0x000000000fffefff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffefff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffefff] [ 0.000000] percpu: Embedded 16 pages/cpu s35088 r8192 d22256 u65536 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64959 [ 0.000000] Kernel command line: root=/dev/vda rw ip=192.168.7.6::192.168.7.5:255.255.255.0::eth0:off:8.8.8.8 console=ttyS0 console=ttyS1 console=ttyS0 console=tty printk.time=1 [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 240036K/262140K available (12881K kernel code, 1381K rwdata, 3432K rodata, 408K init, 365K bss, 22104K reserved, 0K cma-reserved, 0K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] trace event string verifier disabled [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. [ 0.000000] Trampoline variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 [ 0.000000] NR_IRQS: 256 [ 0.000000] CPU frequency 333.33 MHz [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467719329 ns [ 0.000198] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 12885078012ns [ 0.008064] Console: colour dummy device 80x25 [ 0.010840] printk: console [tty0] enabled [ 0.011500] printk: bootconsole [uart8250] disabled [ 0.000000] Linux version 5.15.103-yocto-standard (oe-user@oe-host) (mips-poky-linux-gcc (GCC) 11.3.0, GNU ld (GNU Binutils) 2.38.20220708) #1 SMP PREEMPT Sat Mar 18 03:05:00 UTC 2023 [ 0.000000] earlycon: uart8250 at I/O port 0x3f8 (options '38400n8') [ 0.000000] printk: bootconsole [uart8250] enabled [ 0.000000] CPU0 revision is: 00019500 (MIPS 34Kc) [ 0.000000] FPU revision is: 00739500 [ 0.000000] OF: fdt: No chosen node found, continuing without [ 0.000000] MIPS: machine is mti,malta [ 0.000000] Software DMA cache coherency enabled [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Primary instruction cache 2kB, VIPT, 2-way, linesize 16 bytes. [ 0.000000] Primary data cache 2kB, 2-way, VIPT, no aliases, linesize 16 bytes [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000000000000-0x0000000000ffffff] [ 0.000000] Normal [mem 0x0000000001000000-0x000000000fffefff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffefff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffefff] [ 0.000000] percpu: Embedded 16 pages/cpu s35088 r8192 d22256 u65536 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64959 [ 0.000000] Kernel command line: root=/dev/vda rw ip=192.168.7.6::192.168.7.5:255.255.255.0::eth0:off:8.8.8.8 console=ttyS0 console=ttyS1 console=ttyS0 console=tty printk.time=1 [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 240036K/262140K available (12881K kernel code, 1381K rwdata, 3432K rodata, 408K init, 365K bss, 22104K reserved, 0K cma-reserved, 0K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] trace event string verifier disabled [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. [ 0.000000] Trampoline variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 [ 0.000000] NR_IRQS: 256 [ 0.000000] CPU frequency 333.33 MHz [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467719329 ns [ 0.000198] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 12885078012ns [ 0.008064] Console: colour dummy device 80x25 [ 0.010840] printk: console [tty0] enabled [ 0.011500] printk: bootconsole [uart8250] disabled [ 0.013357] Calibrating delay loop... 1064.96 BogoMIPS (lpj=5324800) [ 0.051895] pid_max: default: 32768 minimum: 301 [ 0.053331] LSM: Security Framework initializing [ 0.054412] landlock: Up and running. [ 0.057624] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.057772] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.131256] Performance counters: No available PMU. [ 0.132320] rcu: Hierarchical SRCU implementation. [ 0.140209] smp: Bringing up secondary CPUs ... [ 0.140349] smp: Brought up 1 node, 1 CPU [ 0.152845] devtmpfs: initialized [ 0.165490] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.165729] futex hash table entries: 256 (order: 2, 16384 bytes, linear) [ 0.175348] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.462693] raid6: int32x8 gen() 231 MB/s [ 0.635990] raid6: int32x8 xor() 179 MB/s [ 0.813414] raid6: int32x4 gen() 572 MB/s [ 0.992031] raid6: int32x4 xor() 312 MB/s [ 1.164528] raid6: int32x2 gen() 699 MB/s [ 1.342130] raid6: int32x2 xor() 408 MB/s [ 1.519638] raid6: int32x1 gen() 470 MB/s [ 1.692140] raid6: int32x1 xor() 294 MB/s [ 1.692345] raid6: using algorithm int32x2 gen() 699 MB/s [ 1.692422] raid6: .... xor() 408 MB/s, rmw enabled [ 1.692562] raid6: using intx1 recovery algorithm [ 1.697858] vgaarb: loaded [ 1.699380] SCSI subsystem initialized [ 1.700086] usbcore: registered new interface driver usbfs [ 1.700441] usbcore: registered new interface driver hub [ 1.700700] usbcore: registered new device driver usb [ 1.701162] pps_core: LinuxPPS API ver. 1 registered [ 1.701227] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 1.701398] PTP clock support registered [ 1.721569] PCI host bridge to bus 0000:00 [ 1.722517] pci_bus 0000:00: root bus resource [mem 0x10000000-0x17ffffff] [ 1.723111] pci_bus 0000:00: root bus resource [io 0x1000-0x1fffff] [ 1.723305] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 1.724816] pci 0000:00:00.0: [11ab:4620] type 00 class 0x060000 [ 1.725576] pci 0000:00:00.0: [Firmware Bug]: reg 0x14: invalid BAR (can't size) [ 1.725672] pci 0000:00:00.0: [Firmware Bug]: reg 0x18: invalid BAR (can't size) [ 1.725751] pci 0000:00:00.0: [Firmware Bug]: reg 0x1c: invalid BAR (can't size) [ 1.725826] pci 0000:00:00.0: [Firmware Bug]: reg 0x20: invalid BAR (can't size) [ 1.725911] pci 0000:00:00.0: [Firmware Bug]: reg 0x24: invalid BAR (can't size) [ 1.728264] pci 0000:00:0a.0: [8086:7110] type 00 class 0x060100 [ 1.728968] pci 0000:00:0a.1: [8086:7111] type 00 class 0x010180 [ 1.729254] pci 0000:00:0a.1: reg 0x20: [io 0x0000-0x000f] [ 1.729381] pci 0000:00:0a.1: legacy IDE quirk: reg 0x10: [io 0x01f0-0x01f7] [ 1.729462] pci 0000:00:0a.1: legacy IDE quirk: reg 0x14: [io 0x03f6] [ 1.729555] pci 0000:00:0a.1: legacy IDE quirk: reg 0x18: [io 0x0170-0x0177] [ 1.729629] pci 0000:00:0a.1: legacy IDE quirk: reg 0x1c: [io 0x0376] [ 1.730139] pci 0000:00:0a.2: [8086:7112] type 00 class 0x0c0300 [ 1.730255] pci 0000:00:0a.2: reg 0x20: [io 0x0000-0x001f] [ 1.730874] pci 0000:00:0a.3: [8086:7113] type 00 class 0x068000 [ 1.731354] pci 0000:00:0a.3: quirk: [io 0x1000-0x103f] claimed by PIIX4 ACPI [ 1.731503] pci 0000:00:0a.3: quirk: [io 0x1100-0x110f] claimed by PIIX4 SMB [ 1.732051] pci 0000:00:12.0: [1234:1111] type 00 class 0x030000 [ 1.732139] pci 0000:00:12.0: reg 0x10: [mem 0x00000000-0x00ffffff pref] [ 1.732280] pci 0000:00:12.0: reg 0x18: [mem 0x00000000-0x00000fff] [ 1.732361] pci 0000:00:12.0: reg 0x30: [mem 0x00000000-0x0000ffff pref] [ 1.732810] pci 0000:00:12.0: vgaarb: VGA device added: decodes=io+mem,owns=none,locks=none [ 1.733172] pci 0000:00:13.0: [1af4:1000] type 00 class 0x020000 [ 1.733270] pci 0000:00:13.0: reg 0x10: [io 0x0000-0x001f] [ 1.733436] pci 0000:00:13.0: reg 0x20: [mem 0x00000000-0x00003fff 64bit pref] [ 1.733578] pci 0000:00:13.0: reg 0x30: [mem 0x00000000-0x0003ffff pref] [ 1.733959] pci 0000:00:14.0: [1af4:1005] type 00 class 0x00ff00 [ 1.734052] pci 0000:00:14.0: reg 0x10: [io 0x0000-0x001f] [ 1.734141] pci 0000:00:14.0: reg 0x20: [mem 0x00000000-0x00003fff 64bit pref] [ 1.734524] pci 0000:00:15.0: [1af4:1001] type 00 class 0x010000 [ 1.734614] pci 0000:00:15.0: reg 0x10: [io 0x0000-0x007f] [ 1.734704] pci 0000:00:15.0: reg 0x20: [mem 0x00000000-0x00003fff 64bit pref] [ 1.735407] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00 [ 1.736794] pci 0000:00:12.0: BAR 0: assigned [mem 0x10000000-0x10ffffff pref] [ 1.737124] pci 0000:00:13.0: BAR 6: assigned [mem 0x11000000-0x1103ffff pref] [ 1.737256] pci 0000:00:12.0: BAR 6: assigned [mem 0x11040000-0x1104ffff pref] [ 1.737364] pci 0000:00:13.0: BAR 4: assigned [mem 0x11050000-0x11053fff 64bit pref] [ 1.737522] pci 0000:00:14.0: BAR 4: assigned [mem 0x11054000-0x11057fff 64bit pref] [ 1.737618] pci 0000:00:15.0: BAR 4: assigned [mem 0x11058000-0x1105bfff 64bit pref] [ 1.737735] pci 0000:00:12.0: BAR 2: assigned [mem 0x1105c000-0x1105cfff] [ 1.737848] pci 0000:00:15.0: BAR 0: assigned [io 0x1080-0x10ff] [ 1.737934] pci 0000:00:0a.2: BAR 4: assigned [io 0x1040-0x105f] [ 1.737998] pci 0000:00:13.0: BAR 0: assigned [io 0x1060-0x107f] [ 1.738070] pci 0000:00:14.0: BAR 0: assigned [io 0x1400-0x141f] [ 1.738143] pci 0000:00:0a.1: BAR 4: assigned [io 0x1420-0x142f] [ 1.740948] clocksource: Switched to clocksource MIPS [ 1.903482] NET: Registered PF_INET protocol family [ 1.904682] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 1.924763] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 1.924922] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 1.925050] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 1.925292] TCP bind hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 1.925475] TCP: Hash tables configured (established 2048 bind 2048) [ 1.926662] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 1.926952] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 1.928750] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 1.932365] RPC: Registered named UNIX socket transport module. [ 1.932476] RPC: Registered udp transport module. [ 1.932532] RPC: Registered tcp transport module. [ 1.932588] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.933642] pci 0000:00:0a.2: enabling device (0000 -> 0001) [ 1.934446] PCI: CLS 0 bytes, default 16 [ 2.388728] workingset: timestamp_bits=14 max_order=16 bucket_order=2 [ 2.407893] NFS: Registering the id_resolver key type [ 2.409254] Key type id_resolver registered [ 2.409347] Key type id_legacy registered [ 2.412347] Key type cifs.idmap registered [ 2.554288] xor: measuring software checksum speed [ 2.565185] 8regs : 961 MB/sec [ 2.576031] 8regs_prefetch : 938 MB/sec [ 2.586573] 32regs : 962 MB/sec [ 2.597993] 32regs_prefetch : 886 MB/sec [ 2.598093] xor: using function: 32regs (962 MB/sec) [ 2.598618] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251) [ 2.598837] io scheduler mq-deadline registered [ 2.598960] io scheduler kyber registered [ 2.604025] virtio-pci 0000:00:13.0: enabling device (0000 -> 0003) [ 2.606951] virtio-pci 0000:00:14.0: enabling device (0000 -> 0003) [ 2.608031] virtio-pci 0000:00:15.0: enabling device (0000 -> 0003) [ 2.610140] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 2.616072] printk: console [ttyS0] disabled [ 2.639965] serial8250.0: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A [ 2.640094] serial8250.0: ttyS0 extra baud rates supported: 230400, 460800 [ 2.665887] printk: console [ttyS0] enabled [ 2.689036] serial8250.0: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A [ 2.689334] serial8250.0: ttyS1 extra baud rates supported: 230400, 460800 [ 2.689838] serial8250 serial8250.0: unable to register port at index 2 (IO0 MEM1f000900 IRQ20): -28 [ 2.701249] random: crng init done [ 2.702453] bochs-drm 0000:00:12.0: enabling device (0000 -> 0002) [ 2.703512] [drm] Found bochs VGA, ID 0xb0c5. [ 2.703741] [drm] Framebuffer size 16384 kB @ 0x10000000, mmio @ 0x1105c000. [ 2.707237] [drm] Found EDID data blob. [ 2.712730] [drm] Initialized bochs-drm 1.0.0 20130925 for 0000:00:12.0 on minor 0 [ 5.930122] Console: switching to colour frame buffer device 128x48 [ 5.966522] bochs-drm 0000:00:12.0: [drm] fb0: bochs-drmdrmfb frame buffer device [ 5.998717] brd: module loaded [ 6.004402] virtio_blk virtio2: [vda] 24150 512-byte logical blocks (12.4 MB/11.8 MiB) [ 6.076484] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 6.077213] ehci-pci: EHCI PCI platform driver [ 6.077834] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 6.078390] ohci-pci: OHCI PCI platform driver [ 6.078984] uhci_hcd: USB Universal Host Controller Interface driver [ 6.080868] uhci_hcd 0000:00:0a.2: UHCI Host Controller [ 6.082323] uhci_hcd 0000:00:0a.2: new USB bus registered, assigned bus number 1 [ 6.083606] uhci_hcd 0000:00:0a.2: irq 11, io base 0x00001040 [ 6.092308] hub 1-0:1.0: USB hub found [ 6.095933] hub 1-0:1.0: 2 ports detected [ 6.103077] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 6.104250] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 6.111196] device-mapper: ioctl: 4.45.0-ioctl (2021-03-22) initialised: dm-devel@redhat.com [ 6.115927] usbcore: registered new interface driver usbhid [ 6.116468] usbhid: USB HID core driver [ 6.117380] u32 classifier [ 6.117682] input device check on [ 6.118003] Actions configured [ 6.120216] NET: Registered PF_INET6 protocol family [ 6.130658] Segment Routing with IPv6 [ 6.145800] In-situ OAM (IOAM) with IPv6 [ 6.151252] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 6.158699] NET: Registered PF_PACKET protocol family [ 6.177174] Bridge firewalling registered [ 6.187487] Key type dns_resolver registered [ 6.195525] NET: Registered PF_VSOCK protocol family [ 6.214319] input: AT Raw Set 2 keyboard as /devices/platform/i8042/serio0/input/input0 [ 6.234526] Key type .fscrypt registered [ 6.252160] Key type fscrypt-provisioning registered [ 6.264936] Btrfs loaded, crc32c=crc32c-generic, zoned=no, fsverity=no [ 6.294852] Key type encrypted registered [ 6.315060] printk: console [netcon0] enabled [ 6.321393] netconsole: network logging started [ 6.391025] usb 1-1: new full-speed USB device number 2 using uhci_hcd [ 9.338278] input: QEMU QEMU USB Tablet as /devices/pci0000:00/0000:00:0a.2/usb1/1-1/1-1:1.0/0003:0627:0001.0001/input/input3 [ 9.344992] hid-generic 0003:0627:0001.0001: input: USB HID v0.01 Mouse [QEMU QEMU USB Tablet] on usb-0000:00:0a.2-1/input0 [ 9.482726] input: ImExPS/2 Generic Explorer Mouse as /devices/platform/i8042/serio1/input/input2 [ 9.587160] IP-Config: Complete: [ 9.593813] device=eth0, hwaddr=52:54:00:12:34:06, ipaddr=192.168.7.6, mask=255.255.255.0, gw=192.168.7.5 [ 9.598745] host=192.168.7.6, domain=, nis-domain=(none) [ 9.603522] bootserver=255.255.255.255, rootserver=255.255.255.255, rootpath= [ 9.603594] nameserver0=8.8.8.8 [ 9.621253] md: Waiting for all devices to be available before autodetect [ 9.627868] md: If you don't use raid, use raid=noautodetect [ 9.641034] md: Autodetecting RAID arrays. [ 9.645846] md: autorun ... [ 9.650224] md: ... autorun DONE. [ 9.724002] EXT4-fs (vda): mounted filesystem with ordered data mode. Opts: (null). Quota mode: disabled. [ 9.730887] VFS: Mounted root (ext4 filesystem) on device 253:0. [ 9.765363] devtmpfs: mounted [ 9.834819] Freeing unused kernel image (initmem) memory: 408K [ 9.852956] This architecture does not have kernel memory protection. [ 9.860753] Run /sbin/init as init process [ 9.885640] process '/sbin/init.sysvinit' started with executable stack [ 11.925231] udevd[110]: starting version 3.2.10 [ 12.041482] udevd[111]: starting eudev-3.2.10 [ 13.980669] EXT4-fs (vda): re-mounted. Opts: (null). Quota mode: disabled. hwclock: can't open '/dev/misc/rtc': No such file or directory INIT: bootlogd: writing to console: Input/output error Entering runlevel: 5 Configuring network interfaces... ip: RTNETLINK answers: File exists hwclock: can't open '/dev/misc/rtc': No such file or directory Starting syslogd/klogd: done Poky (Yocto Project Reference Distro) 4.0.9 qemumips /dev/ttyS0 qemumips login: