[ 0.000000] Linux version 5.15.103-yocto-standard (oe-user@oe-host) (mips-poky-linux-gcc (GCC) 11.3.0, GNU ld (GNU Binutils) 2.38.20220708) #1 SMP PREEMPT Sat Mar 18 03:05:00 UTC 2023 [ 0.000000] earlycon: uart8250 at I/O port 0x3f8 (options '38400n8') [ 0.000000] printk: bootconsole [uart8250] enabled [ 0.000000] CPU0 revision is: 00019500 (MIPS 34Kc) [ 0.000000] FPU revision is: 00739500 [ 0.000000] OF: fdt: No chosen node found, continuing without [ 0.000000] MIPS: machine is mti,malta [ 0.000000] Software DMA cache coherency enabled [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Primary instruction cache 2kB, VIPT, 2-way, linesize 16 bytes. [ 0.000000] Primary data cache 2kB, 2-way, VIPT, no aliases, linesize 16 bytes [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000000000000-0x0000000000ffffff] [ 0.000000] Normal [mem 0x0000000001000000-0x000000000fffefff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffefff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffefff] [ 0.000000] percpu: Embedded 16 pages/cpu s35088 r8192 d22256 u65536 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64959 [ 0.000000] Kernel command line: root=/dev/vda rw ip=192.168.7.4::192.168.7.3:255.255.255.0::eth0:off:8.8.8.8 console=ttyS0 console=ttyS1 console=ttyS0 console=tty printk.time=1 [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 240036K/262140K available (12881K kernel code, 1381K rwdata, 3432K rodata, 408K init, 365K bss, 22104K reserved, 0K cma-reserved, 0K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] trace event string verifier disabled [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. [ 0.000000] Trampoline variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 [ 0.000000] NR_IRQS: 256 [ 0.000000] CPU frequency 333.34 MHz [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467346265 ns [ 0.000202] sched_clock: 32 bits at 166MHz, resolution 5ns, wraps every 12884659197ns [ 0.008259] Console: colour dummy device 80x25 [ 0.011115] printk: console [tty0] enabled [ 0.011782] printk: bootconsole [uart8250] disabled [ 0.000000] Linux version 5.15.103-yocto-standard (oe-user@oe-host) (mips-poky-linux-gcc (GCC) 11.3.0, GNU ld (GNU Binutils) 2.38.20220708) #1 SMP PREEMPT Sat Mar 18 03:05:00 UTC 2023 [ 0.000000] earlycon: uart8250 at I/O port 0x3f8 (options '38400n8') [ 0.000000] printk: bootconsole [uart8250] enabled [ 0.000000] CPU0 revision is: 00019500 (MIPS 34Kc) [ 0.000000] FPU revision is: 00739500 [ 0.000000] OF: fdt: No chosen node found, continuing without [ 0.000000] MIPS: machine is mti,malta [ 0.000000] Software DMA cache coherency enabled [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Primary instruction cache 2kB, VIPT, 2-way, linesize 16 bytes. [ 0.000000] Primary data cache 2kB, 2-way, VIPT, no aliases, linesize 16 bytes [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000000000000-0x0000000000ffffff] [ 0.000000] Normal [mem 0x0000000001000000-0x000000000fffefff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffefff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffefff] [ 0.000000] percpu: Embedded 16 pages/cpu s35088 r8192 d22256 u65536 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64959 [ 0.000000] Kernel command line: root=/dev/vda rw ip=192.168.7.4::192.168.7.3:255.255.255.0::eth0:off:8.8.8.8 console=ttyS0 console=ttyS1 console=ttyS0 console=tty printk.time=1 [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 240036K/262140K available (12881K kernel code, 1381K rwdata, 3432K rodata, 408K init, 365K bss, 22104K reserved, 0K cma-reserved, 0K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] trace event string verifier disabled [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. [ 0.000000] Trampoline variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 [ 0.000000] NR_IRQS: 256 [ 0.000000] CPU frequency 333.34 MHz [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467346265 ns [ 0.000202] sched_clock: 32 bits at 166MHz, resolution 5ns, wraps every 12884659197ns [ 0.008259] Console: colour dummy device 80x25 [ 0.011115] printk: console [tty0] enabled [ 0.011782] printk: bootconsole [uart8250] disabled [ 0.013731] Calibrating delay loop... 1059.22 BogoMIPS (lpj=5296128) [ 0.051778] pid_max: default: 32768 minimum: 301 [ 0.052789] LSM: Security Framework initializing [ 0.053979] landlock: Up and running. [ 0.057301] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.057458] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.102529] Performance counters: No available PMU. [ 0.103669] rcu: Hierarchical SRCU implementation. [ 0.111515] smp: Bringing up secondary CPUs ... [ 0.111653] smp: Brought up 1 node, 1 CPU [ 0.125092] devtmpfs: initialized [ 0.133042] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.133271] futex hash table entries: 256 (order: 2, 16384 bytes, linear) [ 0.143092] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.395993] raid6: int32x8 gen() 240 MB/s [ 0.568162] raid6: int32x8 xor() 179 MB/s [ 0.746227] raid6: int32x4 gen() 643 MB/s [ 0.925843] raid6: int32x4 xor() 363 MB/s [ 1.097274] raid6: int32x2 gen() 702 MB/s [ 1.277137] raid6: int32x2 xor() 419 MB/s [ 1.457705] raid6: int32x1 gen() 575 MB/s [ 1.628664] raid6: int32x1 xor() 316 MB/s [ 1.628817] raid6: using algorithm int32x2 gen() 702 MB/s [ 1.628887] raid6: .... xor() 419 MB/s, rmw enabled [ 1.629013] raid6: using intx1 recovery algorithm [ 1.634194] vgaarb: loaded [ 1.635725] SCSI subsystem initialized [ 1.636451] usbcore: registered new interface driver usbfs [ 1.636818] usbcore: registered new interface driver hub [ 1.637082] usbcore: registered new device driver usb [ 1.637562] pps_core: LinuxPPS API ver. 1 registered [ 1.637628] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 1.637803] PTP clock support registered [ 1.659514] PCI host bridge to bus 0000:00 [ 1.660396] pci_bus 0000:00: root bus resource [mem 0x10000000-0x17ffffff] [ 1.661009] pci_bus 0000:00: root bus resource [io 0x1000-0x1fffff] [ 1.661208] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 1.662792] pci 0000:00:00.0: [11ab:4620] type 00 class 0x060000 [ 1.663586] pci 0000:00:00.0: [Firmware Bug]: reg 0x14: invalid BAR (can't size) [ 1.663683] pci 0000:00:00.0: [Firmware Bug]: reg 0x18: invalid BAR (can't size) [ 1.663762] pci 0000:00:00.0: [Firmware Bug]: reg 0x1c: invalid BAR (can't size) [ 1.663836] pci 0000:00:00.0: [Firmware Bug]: reg 0x20: invalid BAR (can't size) [ 1.663921] pci 0000:00:00.0: [Firmware Bug]: reg 0x24: invalid BAR (can't size) [ 1.666404] pci 0000:00:0a.0: [8086:7110] type 00 class 0x060100 [ 1.667103] pci 0000:00:0a.1: [8086:7111] type 00 class 0x010180 [ 1.667397] pci 0000:00:0a.1: reg 0x20: [io 0x0000-0x000f] [ 1.667611] pci 0000:00:0a.1: legacy IDE quirk: reg 0x10: [io 0x01f0-0x01f7] [ 1.667701] pci 0000:00:0a.1: legacy IDE quirk: reg 0x14: [io 0x03f6] [ 1.667799] pci 0000:00:0a.1: legacy IDE quirk: reg 0x18: [io 0x0170-0x0177] [ 1.667874] pci 0000:00:0a.1: legacy IDE quirk: reg 0x1c: [io 0x0376] [ 1.668284] pci 0000:00:0a.2: [8086:7112] type 00 class 0x0c0300 [ 1.668396] pci 0000:00:0a.2: reg 0x20: [io 0x0000-0x001f] [ 1.668988] pci 0000:00:0a.3: [8086:7113] type 00 class 0x068000 [ 1.669494] pci 0000:00:0a.3: quirk: [io 0x1000-0x103f] claimed by PIIX4 ACPI [ 1.669648] pci 0000:00:0a.3: quirk: [io 0x1100-0x110f] claimed by PIIX4 SMB [ 1.670193] pci 0000:00:12.0: [1234:1111] type 00 class 0x030000 [ 1.670280] pci 0000:00:12.0: reg 0x10: [mem 0x00000000-0x00ffffff pref] [ 1.670426] pci 0000:00:12.0: reg 0x18: [mem 0x00000000-0x00000fff] [ 1.670506] pci 0000:00:12.0: reg 0x30: [mem 0x00000000-0x0000ffff pref] [ 1.670947] pci 0000:00:12.0: vgaarb: VGA device added: decodes=io+mem,owns=none,locks=none [ 1.671317] pci 0000:00:13.0: [1af4:1000] type 00 class 0x020000 [ 1.671411] pci 0000:00:13.0: reg 0x10: [io 0x0000-0x001f] [ 1.671581] pci 0000:00:13.0: reg 0x20: [mem 0x00000000-0x00003fff 64bit pref] [ 1.671724] pci 0000:00:13.0: reg 0x30: [mem 0x00000000-0x0003ffff pref] [ 1.672096] pci 0000:00:14.0: [1af4:1005] type 00 class 0x00ff00 [ 1.672187] pci 0000:00:14.0: reg 0x10: [io 0x0000-0x001f] [ 1.672274] pci 0000:00:14.0: reg 0x20: [mem 0x00000000-0x00003fff 64bit pref] [ 1.672645] pci 0000:00:15.0: [1af4:1001] type 00 class 0x010000 [ 1.672735] pci 0000:00:15.0: reg 0x10: [io 0x0000-0x007f] [ 1.672822] pci 0000:00:15.0: reg 0x20: [mem 0x00000000-0x00003fff 64bit pref] [ 1.673536] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00 [ 1.674978] pci 0000:00:12.0: BAR 0: assigned [mem 0x10000000-0x10ffffff pref] [ 1.675311] pci 0000:00:13.0: BAR 6: assigned [mem 0x11000000-0x1103ffff pref] [ 1.675446] pci 0000:00:12.0: BAR 6: assigned [mem 0x11040000-0x1104ffff pref] [ 1.675553] pci 0000:00:13.0: BAR 4: assigned [mem 0x11050000-0x11053fff 64bit pref] [ 1.675710] pci 0000:00:14.0: BAR 4: assigned [mem 0x11054000-0x11057fff 64bit pref] [ 1.675806] pci 0000:00:15.0: BAR 4: assigned [mem 0x11058000-0x1105bfff 64bit pref] [ 1.675922] pci 0000:00:12.0: BAR 2: assigned [mem 0x1105c000-0x1105cfff] [ 1.676036] pci 0000:00:15.0: BAR 0: assigned [io 0x1080-0x10ff] [ 1.676122] pci 0000:00:0a.2: BAR 4: assigned [io 0x1040-0x105f] [ 1.676187] pci 0000:00:13.0: BAR 0: assigned [io 0x1060-0x107f] [ 1.676259] pci 0000:00:14.0: BAR 0: assigned [io 0x1400-0x141f] [ 1.676333] pci 0000:00:0a.1: BAR 4: assigned [io 0x1420-0x142f] [ 1.679150] clocksource: Switched to clocksource MIPS [ 1.841414] NET: Registered PF_INET protocol family [ 1.842642] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 1.851478] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 1.851637] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 1.851766] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 1.852006] TCP bind hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 1.852187] TCP: Hash tables configured (established 2048 bind 2048) [ 1.853426] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 1.853727] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 1.855579] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 1.871233] RPC: Registered named UNIX socket transport module. [ 1.871346] RPC: Registered udp transport module. [ 1.871402] RPC: Registered tcp transport module. [ 1.871451] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.872552] pci 0000:00:0a.2: enabling device (0000 -> 0001) [ 1.873400] PCI: CLS 0 bytes, default 16 [ 2.318324] workingset: timestamp_bits=14 max_order=16 bucket_order=2 [ 2.334697] NFS: Registering the id_resolver key type [ 2.336085] Key type id_resolver registered [ 2.336178] Key type id_legacy registered [ 2.339135] Key type cifs.idmap registered [ 2.474107] xor: measuring software checksum speed [ 2.484933] 8regs : 963 MB/sec [ 2.495735] 8regs_prefetch : 940 MB/sec [ 2.506192] 32regs : 963 MB/sec [ 2.517596] 32regs_prefetch : 887 MB/sec [ 2.517691] xor: using function: 32regs (963 MB/sec) [ 2.518196] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251) [ 2.518416] io scheduler mq-deadline registered [ 2.518657] io scheduler kyber registered [ 2.523729] virtio-pci 0000:00:13.0: enabling device (0000 -> 0003) [ 2.526733] virtio-pci 0000:00:14.0: enabling device (0000 -> 0003) [ 2.527784] virtio-pci 0000:00:15.0: enabling device (0000 -> 0003) [ 2.530061] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 2.536106] printk: console [ttyS0] disabled [ 2.559932] serial8250.0: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A [ 2.560062] serial8250.0: ttyS0 extra baud rates supported: 230400, 460800 [ 2.581258] printk: console [ttyS0] enabled [ 2.603965] serial8250.0: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A [ 2.604240] serial8250.0: ttyS1 extra baud rates supported: 230400, 460800 [ 2.604713] serial8250 serial8250.0: unable to register port at index 2 (IO0 MEM1f000900 IRQ20): -28 [ 2.614279] bochs-drm 0000:00:12.0: enabling device (0000 -> 0002) [ 2.615247] [drm] Found bochs VGA, ID 0xb0c5. [ 2.615455] [drm] Framebuffer size 16384 kB @ 0x10000000, mmio @ 0x1105c000. [ 2.619334] random: crng init done [ 2.620363] [drm] Found EDID data blob. [ 2.625981] [drm] Initialized bochs-drm 1.0.0 20130925 for 0000:00:12.0 on minor 0 [ 2.699992] Console: switching to colour frame buffer device 128x48 [ 2.713421] bochs-drm 0000:00:12.0: [drm] fb0: bochs-drmdrmfb frame buffer device [ 2.746328] brd: module loaded [ 2.753356] virtio_blk virtio2: [vda] 4573020 512-byte logical blocks (2.34 GB/2.18 GiB) [ 2.775315] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.775901] ehci-pci: EHCI PCI platform driver [ 2.776487] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.777014] ohci-pci: OHCI PCI platform driver [ 2.777608] uhci_hcd: USB Universal Host Controller Interface driver [ 2.779443] uhci_hcd 0000:00:0a.2: UHCI Host Controller [ 2.780923] uhci_hcd 0000:00:0a.2: new USB bus registered, assigned bus number 1 [ 2.783921] uhci_hcd 0000:00:0a.2: irq 11, io base 0x00001040 [ 2.792881] hub 1-0:1.0: USB hub found [ 2.793808] hub 1-0:1.0: 2 ports detected [ 2.800997] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 2.802174] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 2.809962] device-mapper: ioctl: 4.45.0-ioctl (2021-03-22) initialised: dm-devel@redhat.com [ 2.813491] usbcore: registered new interface driver usbhid [ 2.815519] usbhid: USB HID core driver [ 2.816427] u32 classifier [ 2.816722] input device check on [ 2.817037] Actions configured [ 2.819456] NET: Registered PF_INET6 protocol family [ 2.828055] Segment Routing with IPv6 [ 2.837857] In-situ OAM (IOAM) with IPv6 [ 2.850631] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.861387] NET: Registered PF_PACKET protocol family [ 2.866676] Bridge firewalling registered [ 2.875206] Key type dns_resolver registered [ 2.887310] NET: Registered PF_VSOCK protocol family [ 2.897373] Key type .fscrypt registered [ 2.904900] Key type fscrypt-provisioning registered [ 2.918710] input: AT Raw Set 2 keyboard as /devices/platform/i8042/serio0/input/input0 [ 2.938754] Btrfs loaded, crc32c=crc32c-generic, zoned=no, fsverity=no [ 2.972429] Key type encrypted registered [ 2.985000] printk: console [netcon0] enabled [ 2.992486] netconsole: network logging started [ 3.099116] usb 1-1: new full-speed USB device number 2 using uhci_hcd [ 3.385258] input: QEMU QEMU USB Tablet as /devices/pci0000:00/0000:00:0a.2/usb1/1-1/1-1:1.0/0003:0627:0001.0001/input/input3 [ 3.400394] hid-generic 0003:0627:0001.0001: input: USB HID v0.01 Mouse [QEMU QEMU USB Tablet] on usb-0000:00:0a.2-1/input0 [ 3.562413] input: ImExPS/2 Generic Explorer Mouse as /devices/platform/i8042/serio1/input/input2 [ 3.669762] IP-Config: Complete: [ 3.694428] device=eth0, hwaddr=52:54:00:12:34:04, ipaddr=192.168.7.4, mask=255.255.255.0, gw=192.168.7.3 [ 3.720191] host=192.168.7.4, domain=, nis-domain=(none) [ 3.743972] bootserver=255.255.255.255, rootserver=255.255.255.255, rootpath= [ 3.744175] nameserver0=8.8.8.8 [ 3.794801] md: Waiting for all devices to be available before autodetect [ 3.803846] md: If you don't use raid, use raid=noautodetect [ 3.808838] md: Autodetecting RAID arrays. [ 3.813295] md: autorun ... [ 3.817659] md: ... autorun DONE. [ 3.831553] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 3.884927] EXT4-fs (vda): mounted filesystem with ordered data mode. Opts: (null). Quota mode: disabled. [ 3.894462] VFS: Mounted root (ext4 filesystem) on device 253:0. [ 3.905564] devtmpfs: mounted [ 3.968059] Freeing unused kernel image (initmem) memory: 408K [ 3.977047] This architecture does not have kernel memory protection. [ 3.991929] Run /sbin/init as init process [ 4.018740] process '/sbin/init.sysvinit' started with executable stack [ 6.550836] udevd[118]: starting version 3.2.10 [ 6.667368] udevd[119]: starting eudev-3.2.10 [ 14.605600] EXT4-fs (vda): re-mounted. Opts: (null). Quota mode: disabled. hwclock: Cannot access the Hardware Clock via any known method. hwclock: Use the --verbose option to see the details of our search for an access method. ALSA: Restoring mixer settings... INIT: bootlogd: writing to console: Input/output error Entering runlevel: 5 Configuring network interfaces... RTNETLINK answers: File exists Starting system message bus: dbus. Starting Connection Manager Starting OpenBSD Secure Shell server: sshd done. Starting Xserver Starting rpcbind daemon... done. Starting bluetooth: X.Org X Server 1.21.1.7 X Protocol Version 11, Revision 0 Current Operating System: Linux qemumips 5.15.103-yocto-standard #1 SMP PREEMPT Sat Mar 18 03:05:00 UTC 2023 mips Kernel command line: root=/dev/vda rw ip=192.168.7.4::192.168.7.3:255.255.255.0::eth0:off:8.8.8.8 console=ttyS0 console=ttyS1 console=ttyS0 console=tty printk.time=1 Current version of pixman: 0.40.0 Before reporting problems, check http://wiki.x.org to make sure that you have the latest version. Markers: (--) probed, (**) from config file, (==) default setting, (++) from command line, (!!) notice, (II) informational, (WW) warning, (EE) error, (NI) not implemented, (??) unknown. (==) Log file: "/var/log/Xorg.0.log", Time: Tue Apr 4 19:07:37 2023 (==) Using system config directory "/usr/share/X11/xorg.conf.d" bluetoothd. hwclock: Cannot access the Hardware Clock via any known method. hwclock: Use the --verbose option to see the details of our search for an access method. Starting syslogd/klogd: done * Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon [A[122G[ ok ] Starting Telephony daemon The XKEYBOARD keymap compiler (xkbcomp) reports: > Warning: Could not resolve keysym XF86EmojiPicker Errors from xkbcomp are not fatal to the X server No makedumpfile found. Starting crond: OK Poky (Yocto Project Reference Distro) 4.0.9 qemumips ttyS0 qemumips login: [ 1520.687157] hellomod: loading out-of-tree module taints kernel. [ 1520.697848] Hello world! [ 1524.036988] Cleaning up hellomod.