[ 0.000000] Linux version 5.15.103-yocto-standard (oe-user@oe-host) (mips-poky-linux-gcc (GCC) 11.3.0, GNU ld (GNU Binutils) 2.38.20220708) #1 SMP PREEMPT Sat Mar 18 03:05:00 UTC 2023 [ 0.000000] earlycon: uart8250 at I/O port 0x3f8 (options '38400n8') [ 0.000000] printk: bootconsole [uart8250] enabled [ 0.000000] CPU0 revision is: 00019500 (MIPS 34Kc) [ 0.000000] FPU revision is: 00739500 [ 0.000000] OF: fdt: No chosen node found, continuing without [ 0.000000] MIPS: machine is mti,malta [ 0.000000] Software DMA cache coherency enabled [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Primary instruction cache 2kB, VIPT, 2-way, linesize 16 bytes. [ 0.000000] Primary data cache 2kB, 2-way, VIPT, no aliases, linesize 16 bytes [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000000000000-0x0000000000ffffff] [ 0.000000] Normal [mem 0x0000000001000000-0x000000000fffefff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffefff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffefff] [ 0.000000] percpu: Embedded 16 pages/cpu s35088 r8192 d22256 u65536 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64959 [ 0.000000] Kernel command line: root=/dev/vda rw ip=192.168.7.10::192.168.7.9:255.255.255.0::eth0:off:8.8.8.8 console=ttyS0 console=ttyS1 console=ttyS0 console=tty printk.time=1 [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 240036K/262140K available (12881K kernel code, 1381K rwdata, 3432K rodata, 408K init, 365K bss, 22104K reserved, 0K cma-reserved, 0K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] trace event string verifier disabled [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. [ 0.000000] Trampoline variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 [ 0.000000] NR_IRQS: 256 [ 0.000000] CPU frequency 333.37 MHz [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11466299597 ns [ 0.000200] sched_clock: 32 bits at 166MHz, resolution 5ns, wraps every 12883482621ns [ 0.011837] Console: colour dummy device 80x25 [ 0.012366] printk: console [tty0] enabled [ 0.013050] printk: bootconsole [uart8250] disabled [ 0.000000] Linux version 5.15.103-yocto-standard (oe-user@oe-host) (mips-poky-linux-gcc (GCC) 11.3.0, GNU ld (GNU Binutils) 2.38.20220708) #1 SMP PREEMPT Sat Mar 18 03:05:00 UTC 2023 [ 0.000000] earlycon: uart8250 at I/O port 0x3f8 (options '38400n8') [ 0.000000] printk: bootconsole [uart8250] enabled [ 0.000000] CPU0 revision is: 00019500 (MIPS 34Kc) [ 0.000000] FPU revision is: 00739500 [ 0.000000] OF: fdt: No chosen node found, continuing without [ 0.000000] MIPS: machine is mti,malta [ 0.000000] Software DMA cache coherency enabled [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Primary instruction cache 2kB, VIPT, 2-way, linesize 16 bytes. [ 0.000000] Primary data cache 2kB, 2-way, VIPT, no aliases, linesize 16 bytes [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000000000000-0x0000000000ffffff] [ 0.000000] Normal [mem 0x0000000001000000-0x000000000fffefff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffefff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffefff] [ 0.000000] percpu: Embedded 16 pages/cpu s35088 r8192 d22256 u65536 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64959 [ 0.000000] Kernel command line: root=/dev/vda rw ip=192.168.7.10::192.168.7.9:255.255.255.0::eth0:off:8.8.8.8 console=ttyS0 console=ttyS1 console=ttyS0 console=tty printk.time=1 [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 240036K/262140K available (12881K kernel code, 1381K rwdata, 3432K rodata, 408K init, 365K bss, 22104K reserved, 0K cma-reserved, 0K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] trace event string verifier disabled [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. [ 0.000000] Trampoline variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 [ 0.000000] NR_IRQS: 256 [ 0.000000] CPU frequency 333.37 MHz [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11466299597 ns [ 0.000200] sched_clock: 32 bits at 166MHz, resolution 5ns, wraps every 12883482621ns [ 0.011837] Console: colour dummy device 80x25 [ 0.012366] printk: console [tty0] enabled [ 0.013050] printk: bootconsole [uart8250] disabled [ 0.015003] Calibrating delay loop... 1070.69 BogoMIPS (lpj=5353472) [ 0.111235] pid_max: default: 32768 minimum: 301 [ 0.112205] LSM: Security Framework initializing [ 0.113341] landlock: Up and running. [ 0.118032] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.118243] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.162327] Performance counters: No available PMU. [ 0.163448] rcu: Hierarchical SRCU implementation. [ 0.170043] smp: Bringing up secondary CPUs ... [ 0.170192] smp: Brought up 1 node, 1 CPU [ 0.185202] devtmpfs: initialized [ 0.193296] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.193529] futex hash table entries: 256 (order: 2, 16384 bytes, linear) [ 0.203342] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.453698] raid6: int32x8 gen() 238 MB/s [ 0.630195] raid6: int32x8 xor() 186 MB/s [ 0.801233] raid6: int32x4 gen() 613 MB/s [ 0.977770] raid6: int32x4 xor() 356 MB/s [ 1.155124] raid6: int32x2 gen() 726 MB/s [ 1.328081] raid6: int32x2 xor() 401 MB/s [ 1.503731] raid6: int32x1 gen() 540 MB/s [ 1.681524] raid6: int32x1 xor() 329 MB/s [ 1.681729] raid6: using algorithm int32x2 gen() 726 MB/s [ 1.681815] raid6: .... xor() 401 MB/s, rmw enabled [ 1.681985] raid6: using intx1 recovery algorithm [ 1.688292] vgaarb: loaded [ 1.689924] SCSI subsystem initialized [ 1.690677] usbcore: registered new interface driver usbfs [ 1.691047] usbcore: registered new interface driver hub [ 1.691309] usbcore: registered new device driver usb [ 1.691884] pps_core: LinuxPPS API ver. 1 registered [ 1.691951] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 1.692126] PTP clock support registered [ 1.746376] PCI host bridge to bus 0000:00 [ 1.746781] pci_bus 0000:00: root bus resource [mem 0x10000000-0x17ffffff] [ 1.747408] pci_bus 0000:00: root bus resource [io 0x1000-0x1fffff] [ 1.747602] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 1.749186] pci 0000:00:00.0: [11ab:4620] type 00 class 0x060000 [ 1.749983] pci 0000:00:00.0: [Firmware Bug]: reg 0x14: invalid BAR (can't size) [ 1.750079] pci 0000:00:00.0: [Firmware Bug]: reg 0x18: invalid BAR (can't size) [ 1.750159] pci 0000:00:00.0: [Firmware Bug]: reg 0x1c: invalid BAR (can't size) [ 1.750257] pci 0000:00:00.0: [Firmware Bug]: reg 0x20: invalid BAR (can't size) [ 1.750348] pci 0000:00:00.0: [Firmware Bug]: reg 0x24: invalid BAR (can't size) [ 1.752838] pci 0000:00:0a.0: [8086:7110] type 00 class 0x060100 [ 1.753553] pci 0000:00:0a.1: [8086:7111] type 00 class 0x010180 [ 1.753847] pci 0000:00:0a.1: reg 0x20: [io 0x0000-0x000f] [ 1.753977] pci 0000:00:0a.1: legacy IDE quirk: reg 0x10: [io 0x01f0-0x01f7] [ 1.754059] pci 0000:00:0a.1: legacy IDE quirk: reg 0x14: [io 0x03f6] [ 1.754157] pci 0000:00:0a.1: legacy IDE quirk: reg 0x18: [io 0x0170-0x0177] [ 1.754242] pci 0000:00:0a.1: legacy IDE quirk: reg 0x1c: [io 0x0376] [ 1.754653] pci 0000:00:0a.2: [8086:7112] type 00 class 0x0c0300 [ 1.754766] pci 0000:00:0a.2: reg 0x20: [io 0x0000-0x001f] [ 1.755429] pci 0000:00:0a.3: [8086:7113] type 00 class 0x068000 [ 1.756031] pci 0000:00:0a.3: quirk: [io 0x1000-0x103f] claimed by PIIX4 ACPI [ 1.756192] pci 0000:00:0a.3: quirk: [io 0x1100-0x110f] claimed by PIIX4 SMB [ 1.756752] pci 0000:00:12.0: [1234:1111] type 00 class 0x030000 [ 1.756840] pci 0000:00:12.0: reg 0x10: [mem 0x00000000-0x00ffffff pref] [ 1.756984] pci 0000:00:12.0: reg 0x18: [mem 0x00000000-0x00000fff] [ 1.757065] pci 0000:00:12.0: reg 0x30: [mem 0x00000000-0x0000ffff pref] [ 1.757516] pci 0000:00:12.0: vgaarb: VGA device added: decodes=io+mem,owns=none,locks=none [ 1.757884] pci 0000:00:13.0: [1af4:1000] type 00 class 0x020000 [ 1.757980] pci 0000:00:13.0: reg 0x10: [io 0x0000-0x001f] [ 1.758156] pci 0000:00:13.0: reg 0x20: [mem 0x00000000-0x00003fff 64bit pref] [ 1.758311] pci 0000:00:13.0: reg 0x30: [mem 0x00000000-0x0003ffff pref] [ 1.758696] pci 0000:00:14.0: [1af4:1005] type 00 class 0x00ff00 [ 1.758786] pci 0000:00:14.0: reg 0x10: [io 0x0000-0x001f] [ 1.758874] pci 0000:00:14.0: reg 0x20: [mem 0x00000000-0x00003fff 64bit pref] [ 1.759254] pci 0000:00:15.0: [1af4:1001] type 00 class 0x010000 [ 1.759343] pci 0000:00:15.0: reg 0x10: [io 0x0000-0x007f] [ 1.759431] pci 0000:00:15.0: reg 0x20: [mem 0x00000000-0x00003fff 64bit pref] [ 1.760140] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00 [ 1.761586] pci 0000:00:12.0: BAR 0: assigned [mem 0x10000000-0x10ffffff pref] [ 1.761917] pci 0000:00:13.0: BAR 6: assigned [mem 0x11000000-0x1103ffff pref] [ 1.762051] pci 0000:00:12.0: BAR 6: assigned [mem 0x11040000-0x1104ffff pref] [ 1.762158] pci 0000:00:13.0: BAR 4: assigned [mem 0x11050000-0x11053fff 64bit pref] [ 1.762321] pci 0000:00:14.0: BAR 4: assigned [mem 0x11054000-0x11057fff 64bit pref] [ 1.762417] pci 0000:00:15.0: BAR 4: assigned [mem 0x11058000-0x1105bfff 64bit pref] [ 1.762533] pci 0000:00:12.0: BAR 2: assigned [mem 0x1105c000-0x1105cfff] [ 1.762647] pci 0000:00:15.0: BAR 0: assigned [io 0x1080-0x10ff] [ 1.762732] pci 0000:00:0a.2: BAR 4: assigned [io 0x1040-0x105f] [ 1.762795] pci 0000:00:13.0: BAR 0: assigned [io 0x1060-0x107f] [ 1.762865] pci 0000:00:14.0: BAR 0: assigned [io 0x1400-0x141f] [ 1.762936] pci 0000:00:0a.1: BAR 4: assigned [io 0x1420-0x142f] [ 1.765732] clocksource: Switched to clocksource MIPS [ 2.085684] NET: Registered PF_INET protocol family [ 2.086988] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 2.099875] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 2.100038] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 2.100169] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 2.100416] TCP bind hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 2.100598] TCP: Hash tables configured (established 2048 bind 2048) [ 2.101859] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 2.102167] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 2.104016] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 2.118248] RPC: Registered named UNIX socket transport module. [ 2.118369] RPC: Registered udp transport module. [ 2.118426] RPC: Registered tcp transport module. [ 2.118475] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 2.119597] pci 0000:00:0a.2: enabling device (0000 -> 0001) [ 2.120464] PCI: CLS 0 bytes, default 16 [ 2.594537] workingset: timestamp_bits=14 max_order=16 bucket_order=2 [ 2.611146] NFS: Registering the id_resolver key type [ 2.612577] Key type id_resolver registered [ 2.612673] Key type id_legacy registered [ 2.615680] Key type cifs.idmap registered [ 2.757786] xor: measuring software checksum speed [ 2.768695] 8regs : 961 MB/sec [ 2.779537] 8regs_prefetch : 937 MB/sec [ 2.790077] 32regs : 962 MB/sec [ 2.801504] 32regs_prefetch : 885 MB/sec [ 2.801612] xor: using function: 32regs (962 MB/sec) [ 2.802150] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251) [ 2.802365] io scheduler mq-deadline registered [ 2.802499] io scheduler kyber registered [ 2.807795] virtio-pci 0000:00:13.0: enabling device (0000 -> 0003) [ 2.811080] virtio-pci 0000:00:14.0: enabling device (0000 -> 0003) [ 2.812341] virtio-pci 0000:00:15.0: enabling device (0000 -> 0003) [ 2.814711] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 2.820944] printk: console [ttyS0] disabled [ 2.844949] serial8250.0: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A [ 2.845076] serial8250.0: ttyS0 extra baud rates supported: 230400, 460800 [ 2.869643] printk: console [ttyS0] enabled [ 2.892691] serial8250.0: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A [ 2.892970] serial8250.0: ttyS1 extra baud rates supported: 230400, 460800 [ 2.893423] serial8250 serial8250.0: unable to register port at index 2 (IO0 MEM1f000900 IRQ20): -28 [ 2.903001] bochs-drm 0000:00:12.0: enabling device (0000 -> 0002) [ 2.904001] [drm] Found bochs VGA, ID 0xb0c5. [ 2.904225] [drm] Framebuffer size 16384 kB @ 0x10000000, mmio @ 0x1105c000. [ 2.906071] random: crng init done [ 2.909176] [drm] Found EDID data blob. [ 2.914862] [drm] Initialized bochs-drm 1.0.0 20130925 for 0000:00:12.0 on minor 0 [ 2.996565] Console: switching to colour frame buffer device 128x48 [ 3.015534] bochs-drm 0000:00:12.0: [drm] fb0: bochs-drmdrmfb frame buffer device [ 3.058210] brd: module loaded [ 3.064266] virtio_blk virtio2: [vda] 4573030 512-byte logical blocks (2.34 GB/2.18 GiB) [ 3.089427] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.090116] ehci-pci: EHCI PCI platform driver [ 3.090746] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 3.091303] ohci-pci: OHCI PCI platform driver [ 3.091917] uhci_hcd: USB Universal Host Controller Interface driver [ 3.093755] uhci_hcd 0000:00:0a.2: UHCI Host Controller [ 3.095404] uhci_hcd 0000:00:0a.2: new USB bus registered, assigned bus number 1 [ 3.096749] uhci_hcd 0000:00:0a.2: irq 11, io base 0x00001040 [ 3.105878] hub 1-0:1.0: USB hub found [ 3.106844] hub 1-0:1.0: 2 ports detected [ 3.116512] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 3.117740] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 3.124709] device-mapper: ioctl: 4.45.0-ioctl (2021-03-22) initialised: dm-devel@redhat.com [ 3.129652] usbcore: registered new interface driver usbhid [ 3.130155] usbhid: USB HID core driver [ 3.131074] u32 classifier [ 3.131381] input device check on [ 3.131699] Actions configured [ 3.134003] NET: Registered PF_INET6 protocol family [ 3.143474] Segment Routing with IPv6 [ 3.155583] In-situ OAM (IOAM) with IPv6 [ 3.163746] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 3.174699] NET: Registered PF_PACKET protocol family [ 3.191465] Bridge firewalling registered [ 3.201209] Key type dns_resolver registered [ 3.209908] NET: Registered PF_VSOCK protocol family [ 3.235844] input: AT Raw Set 2 keyboard as /devices/platform/i8042/serio0/input/input0 [ 3.259474] Key type .fscrypt registered [ 3.264084] Key type fscrypt-provisioning registered [ 3.278830] Btrfs loaded, crc32c=crc32c-generic, zoned=no, fsverity=no [ 3.307034] Key type encrypted registered [ 3.317354] printk: console [netcon0] enabled [ 3.328251] netconsole: network logging started [ 3.415696] usb 1-1: new full-speed USB device number 2 using uhci_hcd [ 3.686292] input: QEMU QEMU USB Tablet as /devices/pci0000:00/0000:00:0a.2/usb1/1-1/1-1:1.0/0003:0627:0001.0001/input/input3 [ 3.693682] hid-generic 0003:0627:0001.0001: input: USB HID v0.01 Mouse [QEMU QEMU USB Tablet] on usb-0000:00:0a.2-1/input0 [ 3.878489] input: ImExPS/2 Generic Explorer Mouse as /devices/platform/i8042/serio1/input/input2 [ 3.946022] IP-Config: Complete: [ 3.955337] device=eth0, hwaddr=52:54:00:12:34:0a, ipaddr=192.168.7.10, mask=255.255.255.0, gw=192.168.7.9 [ 3.963521] host=192.168.7.10, domain=, nis-domain=(none) [ 3.974147] bootserver=255.255.255.255, rootserver=255.255.255.255, rootpath= [ 3.974229] nameserver0=8.8.8.8 [ 4.013388] md: Waiting for all devices to be available before autodetect [ 4.021697] md: If you don't use raid, use raid=noautodetect [ 4.035322] md: Autodetecting RAID arrays. [ 4.040648] md: autorun ... [ 4.050628] md: ... autorun DONE. [ 4.102851] EXT4-fs (vda): mounted filesystem with ordered data mode. Opts: (null). Quota mode: disabled. [ 4.112321] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 4.117634] VFS: Mounted root (ext4 filesystem) on device 253:0. [ 4.130566] devtmpfs: mounted [ 4.208013] Freeing unused kernel image (initmem) memory: 408K [ 4.215275] This architecture does not have kernel memory protection. [ 4.220165] Run /sbin/init as init process [ 4.258740] process '/sbin/init.sysvinit' started with executable stack [ 7.028051] udevd[118]: starting version 3.2.10 [ 7.142726] udevd[119]: starting eudev-3.2.10 [ 15.985749] EXT4-fs (vda): re-mounted. Opts: (null). Quota mode: disabled. hwclock: Cannot access the Hardware Clock via any known method. hwclock: Use the --verbose option to see the details of our search for an access method. ALSA: Restoring mixer settings... INIT: bootlogd: writing to console: Input/output error Entering runlevel: 5 Configuring network interfaces... RTNETLINK answers: File exists Starting system message bus: dbus. Starting Connection Manager Starting OpenBSD Secure Shell server: sshd done. Starting Xserver Starting rpcbind daemon... done. X.Org X Server 1.21.1.7 X Protocol Version 11, Revision 0 Current Operating System: Linux qemumips 5.15.103-yocto-standard #1 SMP PREEMPT Sat Mar 18 03:05:00 UTC 2023 mips Kernel command line: root=/dev/vda rw ip=192.168.7.10::192.168.7.9:255.255.255.0::eth0:off:8.8.8.8 console=ttyS0 console=ttyS1 console=ttyS0 console=tty printk.time=1 Current version of pixman: 0.40.0 Before reporting problems, check http://wiki.x.org to make sure that you have the latest version. Markers: (--) probed, (**) from config file, (==) default setting, (++) from command line, (!!) notice, (II) informational, (WW) warning, (EE) error, (NI) not implemented, (??) unknown. (==) Log file: "/var/log/Xorg.0.log", Time: Wed Apr 12 18:42:21 2023 (==) Using system config directory "/usr/share/X11/xorg.conf.d" Starting bluetooth: bluetoothd. hwclock: Cannot access the Hardware Clock via any known method. hwclock: Use the --verbose option to see the details of our search for an access method. Starting syslogd/klogd: done * Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon [A[122G[ ok ] Starting Telephony daemon The XKEYBOARD keymap compiler (xkbcomp) reports: > Warning: Could not resolve keysym XF86EmojiPicker Errors from xkbcomp are not fatal to the X server No makedumpfile found. Starting crond: OK Poky (Yocto Project Reference Distro) 4.0.9 qemumips ttyS0 qemumips login: [ 1631.028047] hellomod: loading out-of-tree module taints kernel. [ 1631.044138] Hello world! [ 1634.154174] Cleaning up hellomod.