[ 0.000000] Linux version 5.15.103-yocto-standard (oe-user@oe-host) (mips64-poky-linux-gcc (GCC) 11.3.0, GNU ld (GNU Binutils) 2.38.20220708) #1 SMP PREEMPT Sat Mar 18 03:05:03 UTC 2023 [ 0.000000] earlycon: uart8250 at I/O port 0x3f8 (options '38400n8') [ 0.000000] printk: bootconsole [uart8250] enabled [ 0.000000] CPU0 revision is: 00010000 (MIPS GENERIC QEMU) [ 0.000000] FPU revision is: 007f0000 [ 0.000000] OF: fdt: No chosen node found, continuing without [ 0.000000] MIPS: machine is mti,malta [ 0.000000] Software DMA cache coherency enabled [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000000000000-0x0000000000ffffff] [ 0.000000] DMA32 [mem 0x0000000001000000-0x00000000ffffffff] [ 0.000000] Normal empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000] node 0: [mem 0x0000000090000000-0x000000009fffefff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000009fffefff] [ 0.000000] percpu: Embedded 24 pages/cpu s61216 r8192 d28896 u98304 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 120831 [ 0.000000] Kernel command line: root=/dev/vda rw ip=192.168.7.8::192.168.7.7:255.255.255.0::eth0:off:8.8.8.8 console=ttyS0 console=ttyS1 console=ttyS0 console=tty printk.time=1 [ 0.000000] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes, linear) [ 0.000000] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 463204K/524284K available (12663K kernel code, 1894K rwdata, 2864K rodata, 412K init, 350K bss, 61080K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] trace event string verifier disabled [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. [ 0.000000] Trampoline variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 [ 0.000000] NR_IRQS: 256 [ 0.000000] CPU frequency 333.34 MHz [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467284757 ns [ 0.000119] sched_clock: 32 bits at 166MHz, resolution 5ns, wraps every 12884589565ns [ 0.008535] Console: colour dummy device 80x25 [ 0.012021] printk: console [tty0] enabled [ 0.012732] printk: bootconsole [uart8250] disabled [ 0.000000] Linux version 5.15.103-yocto-standard (oe-user@oe-host) (mips64-poky-linux-gcc (GCC) 11.3.0, GNU ld (GNU Binutils) 2.38.20220708) #1 SMP PREEMPT Sat Mar 18 03:05:03 UTC 2023 [ 0.000000] earlycon: uart8250 at I/O port 0x3f8 (options '38400n8') [ 0.000000] printk: bootconsole [uart8250] enabled [ 0.000000] CPU0 revision is: 00010000 (MIPS GENERIC QEMU) [ 0.000000] FPU revision is: 007f0000 [ 0.000000] OF: fdt: No chosen node found, continuing without [ 0.000000] MIPS: machine is mti,malta [ 0.000000] Software DMA cache coherency enabled [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000000000000-0x0000000000ffffff] [ 0.000000] DMA32 [mem 0x0000000001000000-0x00000000ffffffff] [ 0.000000] Normal empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000] node 0: [mem 0x0000000090000000-0x000000009fffefff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000009fffefff] [ 0.000000] percpu: Embedded 24 pages/cpu s61216 r8192 d28896 u98304 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 120831 [ 0.000000] Kernel command line: root=/dev/vda rw ip=192.168.7.8::192.168.7.7:255.255.255.0::eth0:off:8.8.8.8 console=ttyS0 console=ttyS1 console=ttyS0 console=tty printk.time=1 [ 0.000000] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes, linear) [ 0.000000] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 463204K/524284K available (12663K kernel code, 1894K rwdata, 2864K rodata, 412K init, 350K bss, 61080K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] trace event string verifier disabled [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. [ 0.000000] Trampoline variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 [ 0.000000] NR_IRQS: 256 [ 0.000000] CPU frequency 333.34 MHz [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467284757 ns [ 0.000119] sched_clock: 32 bits at 166MHz, resolution 5ns, wraps every 12884589565ns [ 0.008535] Console: colour dummy device 80x25 [ 0.012021] printk: console [tty0] enabled [ 0.012732] printk: bootconsole [uart8250] disabled [ 0.014617] Calibrating delay loop... 978.94 BogoMIPS (lpj=4894720) [ 0.051780] pid_max: default: 32768 minimum: 301 [ 0.052814] LSM: Security Framework initializing [ 0.053999] landlock: Up and running. [ 0.056369] Mount-cache hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.056525] Mountpoint-cache hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.097224] Performance counters: Either hardware does not support performance counters, or not yet implemented. [ 0.098437] rcu: Hierarchical SRCU implementation. [ 0.106858] smp: Bringing up secondary CPUs ... [ 0.107039] smp: Brought up 1 node, 1 CPU [ 0.121001] devtmpfs: initialized [ 0.129477] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.129774] futex hash table entries: 256 (order: 2, 16384 bytes, linear) [ 0.140530] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.390022] raid6: int64x8 gen() 417 MB/s [ 0.563429] raid6: int64x8 xor() 366 MB/s [ 0.738654] raid6: int64x4 gen() 1104 MB/s [ 0.913651] raid6: int64x4 xor() 611 MB/s [ 1.086377] raid6: int64x2 gen() 1343 MB/s [ 1.262849] raid6: int64x2 xor() 761 MB/s [ 1.439549] raid6: int64x1 gen() 1044 MB/s [ 1.611507] raid6: int64x1 xor() 600 MB/s [ 1.611670] raid6: using algorithm int64x2 gen() 1343 MB/s [ 1.611779] raid6: .... xor() 761 MB/s, rmw enabled [ 1.611916] raid6: using intx1 recovery algorithm [ 1.617068] vgaarb: loaded [ 1.618621] SCSI subsystem initialized [ 1.619287] usbcore: registered new interface driver usbfs [ 1.619649] usbcore: registered new interface driver hub [ 1.619887] usbcore: registered new device driver usb [ 1.620355] pps_core: LinuxPPS API ver. 1 registered [ 1.620417] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 1.620580] PTP clock support registered [ 1.633871] PCI host bridge to bus 0000:00 [ 1.634261] pci_bus 0000:00: root bus resource [mem 0x10000000-0x17ffffff] [ 1.635408] pci_bus 0000:00: root bus resource [io 0x1000-0x1fffff] [ 1.635608] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 1.637172] pci 0000:00:00.0: [11ab:4620] type 00 class 0x060000 [ 1.637955] pci 0000:00:00.0: [Firmware Bug]: reg 0x14: invalid BAR (can't size) [ 1.638048] pci 0000:00:00.0: [Firmware Bug]: reg 0x18: invalid BAR (can't size) [ 1.638123] pci 0000:00:00.0: [Firmware Bug]: reg 0x1c: invalid BAR (can't size) [ 1.638192] pci 0000:00:00.0: [Firmware Bug]: reg 0x20: invalid BAR (can't size) [ 1.638275] pci 0000:00:00.0: [Firmware Bug]: reg 0x24: invalid BAR (can't size) [ 1.640843] pci 0000:00:0a.0: [8086:7110] type 00 class 0x060100 [ 1.641545] pci 0000:00:0a.1: [8086:7111] type 00 class 0x010180 [ 1.641970] pci 0000:00:0a.1: reg 0x20: [io 0x0000-0x000f] [ 1.642127] pci 0000:00:0a.1: legacy IDE quirk: reg 0x10: [io 0x01f0-0x01f7] [ 1.642206] pci 0000:00:0a.1: legacy IDE quirk: reg 0x14: [io 0x03f6] [ 1.642304] pci 0000:00:0a.1: legacy IDE quirk: reg 0x18: [io 0x0170-0x0177] [ 1.642374] pci 0000:00:0a.1: legacy IDE quirk: reg 0x1c: [io 0x0376] [ 1.642791] pci 0000:00:0a.2: [8086:7112] type 00 class 0x0c0300 [ 1.642895] pci 0000:00:0a.2: reg 0x20: [io 0x0000-0x001f] [ 1.643509] pci 0000:00:0a.3: [8086:7113] type 00 class 0x068000 [ 1.644020] pci 0000:00:0a.3: quirk: [io 0x1000-0x103f] claimed by PIIX4 ACPI [ 1.644177] pci 0000:00:0a.3: quirk: [io 0x1100-0x110f] claimed by PIIX4 SMB [ 1.644706] pci 0000:00:12.0: [1234:1111] type 00 class 0x030000 [ 1.644790] pci 0000:00:12.0: reg 0x10: [mem 0x00000000-0x00ffffff pref] [ 1.644931] pci 0000:00:12.0: reg 0x18: [mem 0x00000000-0x00000fff] [ 1.645007] pci 0000:00:12.0: reg 0x30: [mem 0x00000000-0x0000ffff pref] [ 1.645442] pci 0000:00:12.0: vgaarb: VGA device added: decodes=io+mem,owns=none,locks=none [ 1.645825] pci 0000:00:13.0: [1af4:1000] type 00 class 0x020000 [ 1.645915] pci 0000:00:13.0: reg 0x10: [io 0x0000-0x001f] [ 1.646078] pci 0000:00:13.0: reg 0x20: [mem 0x00000000-0x00003fff 64bit pref] [ 1.646216] pci 0000:00:13.0: reg 0x30: [mem 0x00000000-0x0003ffff pref] [ 1.646547] pci 0000:00:14.0: [1af4:1005] type 00 class 0x00ff00 [ 1.646632] pci 0000:00:14.0: reg 0x10: [io 0x0000-0x001f] [ 1.646714] pci 0000:00:14.0: reg 0x20: [mem 0x00000000-0x00003fff 64bit pref] [ 1.647072] pci 0000:00:15.0: [1af4:1001] type 00 class 0x010000 [ 1.647157] pci 0000:00:15.0: reg 0x10: [io 0x0000-0x007f] [ 1.647238] pci 0000:00:15.0: reg 0x20: [mem 0x00000000-0x00003fff 64bit pref] [ 1.647933] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00 [ 1.649475] pci 0000:00:12.0: BAR 0: assigned [mem 0x10000000-0x10ffffff pref] [ 1.655992] pci 0000:00:13.0: BAR 6: assigned [mem 0x11000000-0x1103ffff pref] [ 1.656192] pci 0000:00:12.0: BAR 6: assigned [mem 0x11040000-0x1104ffff pref] [ 1.656393] pci 0000:00:13.0: BAR 4: assigned [mem 0x11050000-0x11053fff 64bit pref] [ 1.656557] pci 0000:00:14.0: BAR 4: assigned [mem 0x11054000-0x11057fff 64bit pref] [ 1.656654] pci 0000:00:15.0: BAR 4: assigned [mem 0x11058000-0x1105bfff 64bit pref] [ 1.656766] pci 0000:00:12.0: BAR 2: assigned [mem 0x1105c000-0x1105cfff] [ 1.656875] pci 0000:00:15.0: BAR 0: assigned [io 0x1080-0x10ff] [ 1.656963] pci 0000:00:0a.2: BAR 4: assigned [io 0x1040-0x105f] [ 1.657023] pci 0000:00:13.0: BAR 0: assigned [io 0x1060-0x107f] [ 1.657090] pci 0000:00:14.0: BAR 0: assigned [io 0x1400-0x141f] [ 1.657149] pci 0000:00:0a.1: BAR 4: assigned [io 0x1420-0x142f] [ 1.659788] clocksource: Switched to clocksource MIPS [ 1.801968] NET: Registered PF_INET protocol family [ 1.803249] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 1.823508] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear) [ 1.823873] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 1.824011] TCP established hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 1.824271] TCP bind hash table entries: 4096 (order: 4, 65536 bytes, linear) [ 1.825025] TCP: Hash tables configured (established 4096 bind 4096) [ 1.826359] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 1.826678] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 1.828578] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 1.842148] RPC: Registered named UNIX socket transport module. [ 1.842304] RPC: Registered udp transport module. [ 1.842359] RPC: Registered tcp transport module. [ 1.842407] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.843558] pci 0000:00:0a.2: enabling device (0000 -> 0001) [ 1.844430] PCI: CLS 0 bytes, default 32 [ 2.312664] workingset: timestamp_bits=46 max_order=17 bucket_order=0 [ 2.328059] NFS: Registering the id_resolver key type [ 2.329646] Key type id_resolver registered [ 2.329755] Key type id_legacy registered [ 2.332694] Key type cifs.idmap registered [ 2.369661] xor: measuring software checksum speed [ 2.376000] 8regs : 1704 MB/sec [ 2.382566] 8regs_prefetch : 1668 MB/sec [ 2.388453] 32regs : 1754 MB/sec [ 2.395094] 32regs_prefetch : 1612 MB/sec [ 2.395272] xor: using function: 32regs (1754 MB/sec) [ 2.395831] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251) [ 2.396074] io scheduler mq-deadline registered [ 2.396199] io scheduler kyber registered [ 2.401631] virtio-pci 0000:00:13.0: enabling device (0000 -> 0003) [ 2.404787] virtio-pci 0000:00:14.0: enabling device (0000 -> 0003) [ 2.405934] virtio-pci 0000:00:15.0: enabling device (0000 -> 0003) [ 2.408204] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 2.414510] printk: console [ttyS0] disabled [ 2.438868] serial8250.0: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A [ 2.439042] serial8250.0: ttyS0 extra baud rates supported: 230400, 460800 [ 2.464080] printk: console [ttyS0] enabled [ 2.486870] serial8250.0: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A [ 2.487205] serial8250.0: ttyS1 extra baud rates supported: 230400, 460800 [ 2.487838] serial8250 serial8250.0: unable to register port at index 2 (IO0 MEM1f000900 IRQ20): -28 [ 2.497705] bochs-drm 0000:00:12.0: enabling device (0000 -> 0002) [ 2.498747] [drm] Found bochs VGA, ID 0xb0c5. [ 2.498979] [drm] Framebuffer size 16384 kB @ 0x10000000, mmio @ 0x1105c000. [ 2.500344] random: crng init done [ 2.504057] [drm] Found EDID data blob. [ 2.510647] [drm] Initialized bochs-drm 1.0.0 20130925 for 0000:00:12.0 on minor 0 [ 2.587342] Console: switching to colour frame buffer device 128x48 [ 2.605982] bochs-drm 0000:00:12.0: [drm] fb0: bochs-drmdrmfb frame buffer device [ 2.643991] brd: module loaded [ 2.650281] virtio_blk virtio2: [vda] 1049676 512-byte logical blocks (537 MB/513 MiB) [ 2.674889] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.675634] ehci-pci: EHCI PCI platform driver [ 2.676241] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.676780] ohci-pci: OHCI PCI platform driver [ 2.689111] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 2.690636] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 2.695514] device-mapper: ioctl: 4.45.0-ioctl (2021-03-22) initialised: dm-devel@redhat.com [ 2.699333] usbcore: registered new interface driver usbhid [ 2.700543] usbhid: USB HID core driver [ 2.701506] u32 classifier [ 2.701790] input device check on [ 2.702092] Actions configured [ 2.704358] NET: Registered PF_INET6 protocol family [ 2.713730] Segment Routing with IPv6 [ 2.714456] In-situ OAM (IOAM) with IPv6 [ 2.715589] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.719195] NET: Registered PF_PACKET protocol family [ 2.720958] Bridge firewalling registered [ 2.722448] Key type dns_resolver registered [ 2.723527] NET: Registered PF_VSOCK protocol family [ 2.736666] Key type .fscrypt registered [ 2.744752] Key type fscrypt-provisioning registered [ 2.757190] Btrfs loaded, crc32c=crc32c-generic, zoned=no, fsverity=no [ 2.791522] Key type encrypted registered [ 2.806617] input: AT Raw Set 2 keyboard as /devices/platform/i8042/serio0/input/input0 [ 2.817696] printk: console [netcon0] enabled [ 2.834627] netconsole: network logging started [ 3.460738] input: ImExPS/2 Generic Explorer Mouse as /devices/platform/i8042/serio1/input/input2 [ 3.560447] IP-Config: Complete: [ 3.572331] device=eth0, hwaddr=52:54:00:12:34:08, ipaddr=192.168.7.8, mask=255.255.255.0, gw=192.168.7.7 [ 3.579681] host=192.168.7.8, domain=, nis-domain=(none) [ 3.585509] bootserver=255.255.255.255, rootserver=255.255.255.255, rootpath= [ 3.585628] nameserver0=8.8.8.8 [ 3.618196] md: Waiting for all devices to be available before autodetect [ 3.627053] md: If you don't use raid, use raid=noautodetect [ 3.640826] md: Autodetecting RAID arrays. [ 3.652869] md: autorun ... [ 3.659655] md: ... autorun DONE. [ 3.729835] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 3.741866] EXT4-fs (vda): mounted filesystem with ordered data mode. Opts: (null). Quota mode: disabled. [ 3.748741] VFS: Mounted root (ext4 filesystem) on device 253:0. [ 3.791067] devtmpfs: mounted [ 3.834634] Freeing unused kernel image (initmem) memory: 412K [ 3.843539] This architecture does not have kernel memory protection. [ 3.852436] Run /sbin/init as init process [ 3.886895] process '/sbin/init.sysvinit' started with executable stack [ 7.895928] udevd[118]: starting version 3.2.10 [ 8.006670] udevd[119]: starting eudev-3.2.10 [ 20.070187] EXT4-fs (vda): re-mounted. Opts: (null). Quota mode: disabled. hwclock: can't open '/dev/misc/rtc': No such file or directory ALSA: Restoring mixer settings... INIT: Entering runlevel: 5 bootlogd: writing to console: Input/output error Configuring network interfaces... ip: RTNETLINK answers: File exists Starting system message bus: dbus. Starting Connection Manager Starting Xserver Starting Dropbear SSH server: dropbear. X.Org X Server 1.21.1.7 X Protocol Version 11, Revision 0 Current Operating System: Linux qemumips64 5.15.103-yocto-standard #1 SMP PREEMPT Sat Mar 18 03:05:03 UTC 2023 mips64 Kernel command line: root=/dev/vda rw ip=192.168.7.8::192.168.7.7:255.255.255.0::eth0:off:8.8.8.8 console=ttyS0 console=ttyS1 console=ttyS0 console=tty printk.time=1 Current version of pixman: 0.40.0 Before reporting problems, check http://wiki.x.org to make sure that you have the latest version. Markers: (--) probed, (**) from config file, (==) default setting, (++) from command line, (!!) notice, (II) informational, (WW) warning, (EE) error, (NI) not implemented, (??) unknown. (==) Log file: "/var/log/Xorg.0.log", Time: Tue Apr 25 00:48:21 2023 (==) Using system config directory "/usr/share/X11/xorg.conf.d" Starting rpcbind daemon...done. Starting bluetooth: bluetoothd. hwclock: can't open '/dev/misc/rtc': No such file or directory The XKEYBOARD keymap compiler (xkbcomp) reports: > Warning: Could not resolve keysym XF86EmojiPicker Errors from xkbcomp are not fatal to the X server Starting syslogd/klogd: done * Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon D-BUS per-session daemon address is: unix:path=/tmp/dbus-xsEeYNGgHw,guid=482ee1f859a6e16eeb523fb86447235a ...done. Starting Telephony daemon Using calibration data stored in /etc/pointercal.xinput Poky (Yocto Project Reference Distro) 4.0.9 qemumips64 /dev/ttyS0 qemumips64 login: