[ 0.000000] Linux version 6.6.75-yocto-standard (oe-user@oe-host) (mips-poky-linux-gcc (GCC) 13.3.0, GNU ld (GNU Binutils) 2.42.0.20240723) #1 SMP PREEMPT Fri Feb 7 21:38:04 UTC 2025 [ 0.000000] earlycon: uart8250 at I/O port 0x3f8 (options '38400n8') [ 0.000000] printk: bootconsole [uart8250] enabled [ 0.000000] CPU0 revision is: 00019500 (MIPS 34Kc) [ 0.000000] FPU revision is: 00739500 [ 0.000000] MIPS: machine is mti,malta [ 0.000000] Software DMA cache coherency enabled [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Primary instruction cache 2kB, VIPT, 2-way, linesize 16 bytes. [ 0.000000] Primary data cache 2kB, 2-way, VIPT, no aliases, linesize 16 bytes [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000000000000-0x0000000000ffffff] [ 0.000000] Normal [mem 0x0000000001000000-0x000000000fffefff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffefff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffefff] [ 0.000000] random: crng init done [ 0.000000] percpu: Embedded 17 pages/cpu s40800 r8192 d20640 u69632 [ 0.000000] Kernel command line: root=/dev/vda rw ip=192.168.7.2::192.168.7.1:255.255.255.0::eth0:off:8.8.8.8 net.ifnames=0 console=ttyS0 console=ttyS1 console=ttyS0 console=tty swiotlb=0 printk.time=1 [ 0.000000] Unknown kernel command line parameters "swiotlb=0", will be passed to user space. [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64959 [ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off [ 0.000000] Memory: 238976K/262140K available (14477K kernel code, 1475K rwdata, 2772K rodata, 400K init, 395K bss, 23164K reserved, 0K cma-reserved, 0K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. [ 0.000000] Trampoline variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 [ 0.000000] NR_IRQS: 256 [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] CPU frequency 320.00 MHz [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11945366817 ns [ 0.000146] sched_clock: 32 bits at 160MHz, resolution 6ns, wraps every 13421760508ns [ 0.006770] Console: colour dummy device 80x25 [ 0.007552] printk: console [tty0] enabled [ 0.008193] printk: bootconsole [uart8250] disabled [ 0.000000] Linux version 6.6.75-yocto-standard (oe-user@oe-host) (mips-poky-linux-gcc (GCC) 13.3.0, GNU ld (GNU Binutils) 2.42.0.20240723) #1 SMP PREEMPT Fri Feb 7 21:38:04 UTC 2025 [ 0.000000] earlycon: uart8250 at I/O port 0x3f8 (options '38400n8') [ 0.000000] printk: bootconsole [uart8250] enabled [ 0.000000] CPU0 revision is: 00019500 (MIPS 34Kc) [ 0.000000] FPU revision is: 00739500 [ 0.000000] MIPS: machine is mti,malta [ 0.000000] Software DMA cache coherency enabled [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Primary instruction cache 2kB, VIPT, 2-way, linesize 16 bytes. [ 0.000000] Primary data cache 2kB, 2-way, VIPT, no aliases, linesize 16 bytes [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000000000000-0x0000000000ffffff] [ 0.000000] Normal [mem 0x0000000001000000-0x000000000fffefff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffefff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffefff] [ 0.000000] random: crng init done [ 0.000000] percpu: Embedded 17 pages/cpu s40800 r8192 d20640 u69632 [ 0.000000] Kernel command line: root=/dev/vda rw ip=192.168.7.2::192.168.7.1:255.255.255.0::eth0:off:8.8.8.8 net.ifnames=0 console=ttyS0 console=ttyS1 console=ttyS0 console=tty swiotlb=0 printk.time=1 [ 0.000000] Unknown kernel command line parameters "swiotlb=0", will be passed to user space. [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64959 [ 0.000000] mem auto-init: stack:all(zero), heap alloc:off, heap free:off [ 0.000000] Memory: 238976K/262140K available (14477K kernel code, 1475K rwdata, 2772K rodata, 400K init, 395K bss, 23164K reserved, 0K cma-reserved, 0K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] rcu: Preemptible hierarchical RCU implementation. [ 0.000000] rcu: RCU event tracing is enabled. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=2 to nr_cpu_ids=1. [ 0.000000] Trampoline variant of Tasks RCU enabled. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=1 [ 0.000000] NR_IRQS: 256 [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] CPU frequency 320.00 MHz [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11945366817 ns [ 0.000146] sched_clock: 32 bits at 160MHz, resolution 6ns, wraps every 13421760508ns [ 0.006770] Console: colour dummy device 80x25 [ 0.007552] printk: console [tty0] enabled [ 0.008193] printk: bootconsole [uart8250] disabled [ 0.012165] Calibrating delay loop... 2393.70 BogoMIPS (lpj=11968512) [ 0.062335] pid_max: default: 32768 minimum: 301 [ 0.063389] LSM: initializing lsm=capability,landlock,integrity [ 0.063816] landlock: Up and running. [ 0.065873] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.065980] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.120533] RCU Tasks: Setting shift to 0 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=1. [ 0.120835] RCU Tasks Trace: Setting shift to 0 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=1. [ 0.121243] Performance counters: No available PMU. [ 0.121975] rcu: Hierarchical SRCU implementation. [ 0.122021] rcu: Max phase no-delay instances is 1000. [ 0.127105] smp: Bringing up secondary CPUs ... [ 0.127354] smp: Brought up 1 node, 1 CPU [ 0.136947] devtmpfs: initialized [ 0.142890] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.143075] futex hash table entries: 256 (order: 2, 16384 bytes, linear) [ 0.175054] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.546288] raid6: int32x8 gen() 459 MB/s [ 0.814259] raid6: int32x4 gen() 961 MB/s [ 0.979193] raid6: int32x2 gen() 964 MB/s [ 1.150830] raid6: int32x1 gen() 868 MB/s [ 1.150940] raid6: using algorithm int32x2 gen() 964 MB/s [ 1.322474] raid6: .... xor() 629 MB/s, rmw enabled [ 1.322594] raid6: using intx1 recovery algorithm [ 1.324736] SCSI subsystem initialized [ 1.325105] usbcore: registered new interface driver usbfs [ 1.325318] usbcore: registered new interface driver hub [ 1.325455] usbcore: registered new device driver usb [ 1.325682] pps_core: LinuxPPS API ver. 1 registered [ 1.325716] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 1.325800] PTP clock support registered [ 1.350194] PCI host bridge to bus 0000:00 [ 1.350484] pci_bus 0000:00: root bus resource [mem 0x10000000-0x17ffffff] [ 1.350863] pci_bus 0000:00: root bus resource [io 0x1000-0x1fffff] [ 1.350965] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 1.352088] pci 0000:00:00.0: [2046:ab11] type 00 class 0x100000 [ 1.352603] pci 0000:00:00.0: [Firmware Bug]: reg 0x10: invalid BAR (can't size) [ 1.352694] pci 0000:00:00.0: [Firmware Bug]: reg 0x14: invalid BAR (can't size) [ 1.352784] pci 0000:00:00.0: [Firmware Bug]: reg 0x18: invalid BAR (can't size) [ 1.352833] pci 0000:00:00.0: [Firmware Bug]: reg 0x1c: invalid BAR (can't size) [ 1.352888] pci 0000:00:00.0: [Firmware Bug]: reg 0x20: invalid BAR (can't size) [ 1.352942] pci 0000:00:00.0: [Firmware Bug]: reg 0x24: invalid BAR (can't size) [ 1.354604] pci 0000:00:0a.0: [8086:7110] type 00 class 0x060100 [ 1.355109] pci 0000:00:0a.1: [8086:7111] type 00 class 0x010180 [ 1.355313] pci 0000:00:0a.1: reg 0x20: [io 0x0000-0x000f] [ 1.355399] pci 0000:00:0a.1: legacy IDE quirk: reg 0x10: [io 0x01f0-0x01f7] [ 1.355442] pci 0000:00:0a.1: legacy IDE quirk: reg 0x14: [io 0x03f6] [ 1.355496] pci 0000:00:0a.1: legacy IDE quirk: reg 0x18: [io 0x0170-0x0177] [ 1.355532] pci 0000:00:0a.1: legacy IDE quirk: reg 0x1c: [io 0x0376] [ 1.355756] pci 0000:00:0a.2: [8086:7112] type 00 class 0x0c0300 [ 1.355850] pci 0000:00:0a.2: reg 0x20: [io 0x0000-0x001f] [ 1.356237] pci 0000:00:0a.3: [8086:7113] type 00 class 0x068000 [ 1.356606] pci 0000:00:0a.3: quirk: [io 0x1000-0x103f] claimed by PIIX4 ACPI [ 1.356691] pci 0000:00:0a.3: quirk: [io 0x1100-0x110f] claimed by PIIX4 SMB [ 1.357042] pci 0000:00:12.0: [1234:1111] type 00 class 0x030000 [ 1.357100] pci 0000:00:12.0: reg 0x10: [mem 0x00000000-0x00ffffff pref] [ 1.357182] pci 0000:00:12.0: reg 0x18: [mem 0x00000000-0x00000fff] [ 1.357239] pci 0000:00:12.0: reg 0x30: [mem 0x00000000-0x0000ffff pref] [ 1.357517] pci 0000:00:13.0: [1af4:1000] type 00 class 0x020000 [ 1.357575] pci 0000:00:13.0: reg 0x10: [io 0x0000-0x001f] [ 1.357651] pci 0000:00:13.0: reg 0x20: [mem 0x00000000-0x00003fff 64bit pref] [ 1.357729] pci 0000:00:13.0: reg 0x30: [mem 0x00000000-0x0003ffff pref] [ 1.357960] pci 0000:00:14.0: [1af4:1005] type 00 class 0x00ff00 [ 1.358014] pci 0000:00:14.0: reg 0x10: [io 0x0000-0x001f] [ 1.358077] pci 0000:00:14.0: reg 0x20: [mem 0x00000000-0x00003fff 64bit pref] [ 1.358314] pci 0000:00:15.0: [1af4:1001] type 00 class 0x010000 [ 1.358364] pci 0000:00:15.0: reg 0x10: [io 0x0000-0x007f] [ 1.358427] pci 0000:00:15.0: reg 0x20: [mem 0x00000000-0x00003fff 64bit pref] [ 1.358884] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00 [ 1.359852] pci 0000:00:12.0: BAR 0: assigned [mem 0x10000000-0x10ffffff pref] [ 1.360058] pci 0000:00:13.0: BAR 6: assigned [mem 0x11000000-0x1103ffff pref] [ 1.360133] pci 0000:00:12.0: BAR 6: assigned [mem 0x11040000-0x1104ffff pref] [ 1.360186] pci 0000:00:13.0: BAR 4: assigned [mem 0x11050000-0x11053fff 64bit pref] [ 1.360276] pci 0000:00:14.0: BAR 4: assigned [mem 0x11054000-0x11057fff 64bit pref] [ 1.360330] pci 0000:00:15.0: BAR 4: assigned [mem 0x11058000-0x1105bfff 64bit pref] [ 1.360396] pci 0000:00:12.0: BAR 2: assigned [mem 0x1105c000-0x1105cfff] [ 1.360453] pci 0000:00:15.0: BAR 0: assigned [io 0x1080-0x10ff] [ 1.360496] pci 0000:00:0a.2: BAR 4: assigned [io 0x1040-0x105f] [ 1.360527] pci 0000:00:13.0: BAR 0: assigned [io 0x1060-0x107f] [ 1.360562] pci 0000:00:14.0: BAR 0: assigned [io 0x1400-0x141f] [ 1.360598] pci 0000:00:0a.1: BAR 4: assigned [io 0x1420-0x142f] [ 1.361980] pci 0000:00:12.0: vgaarb: setting as boot VGA device [ 1.362061] pci 0000:00:12.0: vgaarb: bridge control possible [ 1.362121] pci 0000:00:12.0: vgaarb: VGA device added: decodes=io+mem,owns=none,locks=none [ 1.362197] vgaarb: loaded [ 1.363710] clocksource: Switched to clocksource MIPS [ 1.390230] NET: Registered PF_INET protocol family [ 1.393000] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 1.398126] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 1.398257] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 1.398336] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 1.398487] TCP bind hash table entries: 2048 (order: 3, 32768 bytes, linear) [ 1.398608] TCP: Hash tables configured (established 2048 bind 2048) [ 1.399557] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 1.399744] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 1.400833] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 1.402679] RPC: Registered named UNIX socket transport module. [ 1.402748] RPC: Registered udp transport module. [ 1.402774] RPC: Registered tcp transport module. [ 1.402797] RPC: Registered tcp-with-tls transport module. [ 1.402821] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 1.403482] pci 0000:00:0a.2: enabling device (0000 -> 0001) [ 1.404157] PCI: CLS 0 bytes, default 16 [ 1.410169] workingset: timestamp_bits=14 max_order=16 bucket_order=2 [ 1.412373] NFS: Registering the id_resolver key type [ 1.413564] Key type id_resolver registered [ 1.413620] Key type id_legacy registered [ 1.414915] Key type cifs.idmap registered [ 1.660258] xor: measuring software checksum speed [ 1.662447] 8regs : 1620 MB/sec [ 1.664683] 8regs_prefetch : 1496 MB/sec [ 1.667012] 32regs : 1432 MB/sec [ 1.669230] 32regs_prefetch : 1526 MB/sec [ 1.669283] xor: using function: 8regs (1620 MB/sec) [ 1.669627] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251) [ 1.669765] io scheduler mq-deadline registered [ 1.669827] io scheduler kyber registered [ 1.676281] virtio-pci 0000:00:13.0: enabling device (0000 -> 0003) [ 1.678458] virtio-pci 0000:00:14.0: enabling device (0000 -> 0003) [ 1.679368] virtio-pci 0000:00:15.0: enabling device (0000 -> 0003) [ 1.681012] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 1.686400] printk: console [ttyS0] disabled [ 1.711299] serial8250.0: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A [ 1.711407] serial8250.0: ttyS0 extra baud rates supported: 230400, 460800 [ 1.712625] printk: console [ttyS0] enabled [ 1.817543] serial8250.0: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A [ 1.818478] serial8250.0: ttyS1 extra baud rates supported: 230400, 460800 [ 1.819229] serial8250 serial8250.0: unable to register port at index 2 (IO0 MEM1f000900 IRQ20): -28 [ 1.829383] bochs-drm 0000:00:12.0: vgaarb: deactivate vga console [ 1.831936] bochs-drm 0000:00:12.0: enabling device (0000 -> 0002) [ 1.833564] [drm] Found bochs VGA, ID 0xb0c5. [ 1.834038] [drm] Framebuffer size 16384 kB @ 0x10000000, mmio @ 0x1105c000. [ 1.838688] [drm] Found EDID data blob. [ 1.849458] [drm] Initialized bochs-drm 1.0.0 20130925 for 0000:00:12.0 on minor 0 [ 1.908632] Console: switching to colour frame buffer device 160x50 [ 1.919305] bochs-drm 0000:00:12.0: [drm] fb0: bochs-drmdrmfb frame buffer device [ 1.938979] brd: module loaded [ 1.939965] virtio_blk virtio2: 1/0/0 default/read/poll queues [ 1.945697] virtio_blk virtio2: [vda] 1141186 512-byte logical blocks (584 MB/557 MiB) [ 2.002903] uhci_hcd 0000:00:0a.2: UHCI Host Controller [ 2.005074] uhci_hcd 0000:00:0a.2: new USB bus registered, assigned bus number 1 [ 2.006934] uhci_hcd 0000:00:0a.2: irq 11, io port 0x00001040 [ 2.018863] hub 1-0:1.0: USB hub found [ 2.020205] hub 1-0:1.0: 2 ports detected [ 2.028587] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 2.029567] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 2.033200] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@redhat.com [ 2.035592] usbcore: registered new interface driver usbhid [ 2.036085] usbhid: USB HID core driver [ 2.036819] u32 classifier [ 2.037191] input device check on [ 2.037672] Actions configured [ 2.039851] NET: Registered PF_INET6 protocol family [ 2.058767] Segment Routing with IPv6 [ 2.059360] In-situ OAM (IOAM) with IPv6 [ 2.060220] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 2.062745] NET: Registered PF_PACKET protocol family [ 2.064442] Bridge firewalling registered [ 2.065584] Key type dns_resolver registered [ 2.066405] NET: Registered PF_VSOCK protocol family [ 2.080822] registered taskstats version 1 [ 2.095207] Key type .fscrypt registered [ 2.100403] Key type fscrypt-provisioning registered [ 2.109967] Btrfs loaded, zoned=no, fsverity=no [ 2.133537] Key type encrypted registered [ 2.155749] input: AT Raw Set 2 keyboard as /devices/platform/i8042/serio0/input/input0 [ 2.169287] printk: console [netcon0] enabled [ 2.173482] netconsole: network logging started [ 2.314888] usb 1-1: new full-speed USB device number 2 using uhci_hcd [ 2.574458] input: QEMU QEMU USB Tablet as /devices/pci0000:00/0000:00:0a.2/usb1/1-1/1-1:1.0/0003:0627:0001.0001/input/input3 [ 2.579779] hid-generic 0003:0627:0001.0001: input: USB HID v0.01 Mouse [QEMU QEMU USB Tablet] on usb-0000:00:0a.2-1/input0 [ 2.795041] input: ImExPS/2 Generic Explorer Mouse as /devices/platform/i8042/serio1/input/input2 [ 2.891336] IP-Config: Complete: [ 2.900553] device=eth0, hwaddr=52:54:00:12:34:02, ipaddr=192.168.7.2, mask=255.255.255.0, gw=192.168.7.1 [ 2.910254] host=192.168.7.2, domain=, nis-domain=(none) [ 2.922838] bootserver=255.255.255.255, rootserver=255.255.255.255, rootpath= [ 2.922951] nameserver0=8.8.8.8 [ 2.938080] clk: Disabling unused clocks [ 2.946665] md: Waiting for all devices to be available before autodetect [ 2.954178] md: If you don't use raid, use raid=noautodetect [ 2.959618] md: Autodetecting RAID arrays. [ 2.962639] md: autorun ... [ 2.968041] md: ... autorun DONE. [ 3.074696] EXT4-fs (vda): mounted filesystem 0a355de5-2241-415a-b4b2-c8356334650f r/w with ordered data mode. Quota mode: disabled. [ 3.081295] VFS: Mounted root (ext4 filesystem) on device 253:0. [ 3.091684] devtmpfs: mounted [ 3.145766] Freeing unused kernel image (initmem) memory: 400K [ 3.152524] This architecture does not have kernel memory protection. [ 3.158447] Run /sbin/init as init process [ 3.279061] process '/sbin/init.sysvinit' started with executable stack [ 7.228307] udevd[94]: starting version 3.2.14 [ 7.301026] udevd[95]: starting eudev-3.2.14 [ 19.684311] EXT4-fs (vda): re-mounted 0a355de5-2241-415a-b4b2-c8356334650f r/w. Quota mode: disabled. hwclock: can't open '/dev/misc/rtc': No such file or directory ALSA: Restoring mixer settings... hwclock: can't open '/dev/misc/rtc': No such file or directory INIT: Entering runlevel: 5 bootlogd: writing to console: Input/output error Configuring network interfaces... ip: RTNETLINK answers: File exists Starting system message bus: dbus. Starting Connection Manager Starting Xserver Starting Dropbear SSH server: dropbear. X.Org X Server 1.21.1.16 X Protocol Version 11, Revision 0 Current Operating System: Linux qemumips 6.6.75-yocto-standard #1 SMP PREEMPT Fri Feb 7 21:38:04 UTC 2025 mips Kernel command line: root=/dev/vda rw ip=192.168.7.2::192.168.7.1:255.255.255.0::eth0:off:8.8.8.8 net.ifnames=0 console=ttyS0 console=ttyS1 console=ttyS0 console=tty swiotlb=0 printk.time=1 Current version of pixman: 0.42.2 Before reporting problems, check http://wiki.x.org to make sure that you have the latest version. Markers: (--) probed, (**) from config file, (==) default setting, (++) from command line, (!!) notice, (II) informational, (WW) warning, (EE) error, (NI) not implemented, (??) unknown. (==) Log file: "/var/log/Xorg.0.log", Time: Thu Mar 20 17:40:17 2025 (==) Using config directory: "/etc/X11/xorg.conf.d" (==) Using system config directory "/usr/share/X11/xorg.conf.d" Starting rpcbind daemon...done. pci id for fd 10: 1234:1111, driver (null) MESA-LOADER: failed to open bochs-drm: /usr/lib/dri/bochs-drm_dri.so: cannot open shared object file: No such file or directory (search paths /usr/lib/dri, suffix _dri) Starting bluetooth: bluetoothd. Starting syslogd/klogd: done * Starting Avahi mDNS/DNS-SD Daemon: avahi-daemon ...done. Starting Telephony daemon Poky (Yocto Project Reference Distro) 5.0.8 qemumips /dev/ttyS0 qemumips login: