[ 1.246710] Console: switching to colour frame buffer device 160x50 [ 1.253559] virtio-pci 0000:00:06.0: [drm] fb0: virtio_gpudrmfb frame buffer device [ 1.265206] brd: module loaded [ 1.266373] virtio_blk virtio2: 4/0/0 default/read/poll queues [ 1.271664] virtio_blk virtio2: [vda] 3300624 512-byte logical blocks (1.69 GB/1.57 GiB) [ 1.281935] xhci_hcd 0000:00:04.0: xHCI Host Controller [ 1.282316] xhci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 1 [ 1.284726] xhci_hcd 0000:00:04.0: hcc params 0x00087001 hci version 0x100 quirks 0x0000000000000010 [ 1.289165] xhci_hcd 0000:00:04.0: xHCI Host Controller [ 1.289411] xhci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 2 [ 1.289909] xhci_hcd 0000:00:04.0: Host supports USB 3.0 SuperSpeed [ 1.291397] hub 1-0:1.0: USB hub found [ 1.291795] hub 1-0:1.0: 4 ports detected [ 1.293031] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 1.294582] hub 2-0:1.0: USB hub found [ 1.295056] hub 2-0:1.0: 4 ports detected [ 1.297386] rtc-pl031 9010000.pl031: registered as rtc0 [ 1.297721] rtc-pl031 9010000.pl031: setting system clock to 2026-06-18T17:35:46 UTC (1781804146) [ 1.299410] device-mapper: ioctl: 4.50.0-ioctl (2025-04-28) initialised: dm-devel@lists.linux.dev [ 1.300523] usbcore: registered new interface driver usbhid [ 1.300843] usbhid: USB HID core driver [ 1.301920] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 (0,8000003f) counters available [ 1.302614] u32 classifier [ 1.302734] input device check on [ 1.302965] Actions configured [ 1.303474] NET: Registered PF_INET6 protocol family [ 1.305434] Segment Routing with IPv6 [ 1.305683] In-situ OAM (IOAM) with IPv6 [ 1.306012] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 1.306813] NET: Registered PF_PACKET protocol family [ 1.307164] Bridge firewalling registered [ 1.307574] l2tp_core: L2TP core driver, V2.0 [ 1.308061] Key type dns_resolver registered [ 1.308737] NET: Registered PF_VSOCK protocol family [ 1.312979] registered taskstats version 1 [ 1.323134] Key type .fscrypt registered [ 1.323534] Key type fscrypt-provisioning registered [ 1.324744] Btrfs loaded, zoned=no, fsverity=no [ 1.326987] Key type encrypted registered [ 1.327383] netconsole: network logging started [ 1.347579] IP-Config: Complete: [ 1.347808] device=eth0, hwaddr=52:54:00:12:34:1e, ipaddr=192.168.7.30, mask=255.255.255.0, gw=192.168.7.29 [ 1.348423] host=192.168.7.30, domain=, nis-domain=(none) [ 1.348894] bootserver=255.255.255.255, rootserver=255.255.255.255, rootpath= [ 1.348897] nameserver0=8.8.8.8 [ 1.349861] clk: Disabling unused clocks [ 1.350122] PM: genpd: Disabling unused power domains [ 1.350661] md: Waiting for all devices to be available before autodetect [ 1.351116] md: If you don't use raid, use raid=noautodetect [ 1.351584] md: Autodetecting RAID arrays. [ 1.351832] md: autorun ... [ 1.352026] md: ... autorun DONE. [ 1.371973] EXT4-fs (vda): mounted filesystem abd5f64e-bb47-4f13-8aea-4a83666f795b r/w with ordered data mode. Quota mode: disabled. [ 1.372808] VFS: Mounted root (ext4 filesystem) on device 253:0. [ 1.373802] devtmpfs: mounted [ 1.375842] Freeing unused kernel memory: 1856K [ 1.376391] Run /sbin/init as init process INIT: version 3.14 booting Starting udev [ 1.551596] usb 1-1: new high-speed USB device number 2 using xhci_hcd [ 1.648535] udevd[118]: starting version 3.2.14 [ 1.663040] udevd[119]: starting eudev-3.2.14 [ 1.702041] input: QEMU QEMU USB Tablet as /devices/platform/4010000000.pcie/pci0000:00/0000:00:04.0/usb1/1-1/1-1:1.0/0003:0627:0001.0001/input/input0 [ 1.703726] hid-generic 0003:0627:0001.0001: input: USB HID v0.01 Mouse [QEMU QEMU USB Tablet] on usb-0000:00:04.0-1/input0 [ 1.983841] usb 1-2: new high-speed USB device number 3 using xhci_hcd [ 2.126304] input: QEMU QEMU USB Keyboard as /devices/platform/4010000000.pcie/pci0000:00/0000:00:04.0/usb1/1-2/1-2:1.0/0003:0627:0001.0002/input/input1 [ 2.179731] hid-generic 0003:0627:0001.0002: input: USB HID v1.11 Keyboard [QEMU QEMU USB Keyboard] on usb-0000:00:04.0-2/input0 [ 2.311667] EXT4-fs (vda): re-mounted abd5f64e-bb47-4f13-8aea-4a83666f795b. INIT: Entering runlevel: 5 Configuring network interfaces... Error: ipv4: Address already assigned. Starting OpenBSD Secure Shell server: sshd generating ssh ECDSA host key... done. Starting syslogd/klogd: done Poky (Yocto Project Reference Distro) 6.0.99+snapshot-a673c6c9fa3d7036abf2841a89256666571b666c qemuarm64 hvc0 Type 'root' to login with superuser privileges (no password will be asked). qemuarm64 login: [ 12.294516] loop: module loaded [ 12.634188] loop0: detected capacity change from 0 to 20480 [ 12.864379] loop0: detected capacity change from 0 to 10240 [ 24.972867] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1) [ 24.973641] scsi host0: scsi_debug: version 0191 [20210520] [ 24.973641] dev_size_mb=50, opts=0x0, submit_queues=1, statistics=0 [ 24.976890] scsi 0:0:0:0: Direct-Access Linux scsi_debug 0191 PQ: 0 ANSI: 7 [ 24.977445] scsi 0:0:0:0: Power-on or device reset occurred [ 24.998416] sd 0:0:0:0: [sda] 102400 512-byte logical blocks: (52.4 MB/50.0 MiB) [ 25.002983] sd 0:0:0:0: [sda] Write Protect is off [ 25.011480] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA [ 25.036482] sd 0:0:0:0: [sda] permanent stream count = 5 [ 25.049477] sd 0:0:0:0: [sda] Preferred minimum I/O size 512 bytes [ 25.050139] sd 0:0:0:0: [sda] Optimal transfer size 524288 bytes [ 25.160108] sd 0:0:0:0: [sda] Attached SCSI disk [ 26.273428] sda: sda1 sda2 sda3 sda4 [ 26.644069] sd 0:0:0:0: [sda] Synchronizing SCSI cache [ 27.264465] loop0: detected capacity change from 0 to 10240 [ 27.539116] loop0: p1 [ 33.034866] loop0: detected capacity change from 0 to 8 [ 36.252282] loop0: detected capacity change from 0 to 120 [ 38.357559] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1) [ 38.358506] scsi host0: scsi_debug: version 0191 [20210520] [ 38.358506] dev_size_mb=100, opts=0x0, submit_queues=1, statistics=0 [ 38.362312] scsi 0:0:0:0: Direct-Access Linux scsi_debug 0191 PQ: 0 ANSI: 7 [ 38.362948] scsi 0:0:0:0: Power-on or device reset occurred [ 38.383841] sd 0:0:0:0: [sda] 204800 512-byte logical blocks: (105 MB/100 MiB) [ 38.388509] sd 0:0:0:0: [sda] Write Protect is off [ 38.397102] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA [ 38.422298] sd 0:0:0:0: [sda] permanent stream count = 5 [ 38.434749] sd 0:0:0:0: [sda] Preferred minimum I/O size 512 bytes [ 38.435114] sd 0:0:0:0: [sda] Optimal transfer size 524288 bytes [ 38.519991] sd 0:0:0:0: [sda] Attached SCSI disk [ 39.557870] sd 0:0:0:0: [sda] Spinning up disk... [ 40.571580] .ready [ 40.716127] sd 0:0:0:0: [sda] Synchronizing SCSI cache [ 40.875248] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1) [ 40.876455] scsi host0: scsi_debug: version 0191 [20210520] [ 40.876455] dev_size_mb=100, opts=0x0, submit_queues=1, statistics=0 [ 40.882205] scsi 0:0:0:0: Direct-Access Linux scsi_debug 0191 PQ: 0 ANSI: 7 [ 40.882757] scsi 0:0:0:0: Power-on or device reset occurred [ 40.903704] sd 0:0:0:0: [sda] 204800 512-byte logical blocks: (105 MB/100 MiB) [ 40.908587] sd 0:0:0:0: [sda] Write Protect is off [ 40.917019] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA [ 40.942063] sd 0:0:0:0: [sda] permanent stream count = 5 [ 40.956694] sd 0:0:0:0: [sda] Preferred minimum I/O size 512 bytes [ 40.956942] sd 0:0:0:0: [sda] Optimal transfer size 524288 bytes [ 41.055761] sd 0:0:0:0: [sda] Attached SCSI disk [ 41.712518] EXT4-fs (sda): mounting ext2 file system using the ext4 subsystem [ 41.726403] EXT4-fs (sda): mounted filesystem 7a6c91e9-e69d-4829-be37-6a13bb820033 r/w without journal. Quota mode: disabled. [ 41.785213] EXT4-fs (sda): unmounting filesystem 7a6c91e9-e69d-4829-be37-6a13bb820033. [ 42.812117] sd 0:0:0:0: [sda] Spinning up disk... [ 43.835741] .ready [ 44.012369] sd 0:0:0:0: [sda] Synchronizing SCSI cache [ 44.336020] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1) [ 44.336684] scsi host0: scsi_debug: version 0191 [20210520] [ 44.336684] dev_size_mb=100, opts=0x0, submit_queues=1, statistics=0 [ 44.337890] scsi 0:0:0:0: Direct-Access Linux scsi_debug 0191 PQ: 0 ANSI: 7 [ 44.338613] scsi 0:0:0:0: Power-on or device reset occurred [ 44.359527] sd 0:0:0:0: [sda] 204800 512-byte logical blocks: (105 MB/100 MiB) [ 44.364189] sd 0:0:0:0: [sda] Write Protect is off [ 44.372882] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA [ 44.397847] sd 0:0:0:0: [sda] permanent stream count = 5 [ 44.410272] sd 0:0:0:0: [sda] Preferred minimum I/O size 512 bytes [ 44.410849] sd 0:0:0:0: [sda] Optimal transfer size 524288 bytes [ 44.495889] sd 0:0:0:0: [sda] Attached SCSI disk [ 44.844229] sda: sda1 sda2 [ 45.794055] EXT4-fs (sda1): mounting ext2 file system using the ext4 subsystem [ 45.808129] EXT4-fs (sda1): mounted filesystem 42a96d42-0d3b-4b48-ba85-990fe7f4b384 r/w without journal. Quota mode: disabled. [ 45.879597] EXT4-fs (sda2): mounting ext2 file system using the ext4 subsystem [ 45.892962] EXT4-fs (sda2): mounted filesystem 10383ca1-27b4-4bd1-ac81-a9a9bf59b5ea r/w without journal. Quota mode: disabled. [ 45.948491] EXT4-fs (sda2): unmounting filesystem 10383ca1-27b4-4bd1-ac81-a9a9bf59b5ea. [ 46.003644] EXT4-fs (sda1): unmounting filesystem 42a96d42-0d3b-4b48-ba85-990fe7f4b384. [ 47.030101] sd 0:0:0:0: [sda] Spinning up disk... [ 48.055646] .ready [ 48.140259] sda: sda1 sda2 [ 48.195976] sd 0:0:0:0: [sda] Synchronizing SCSI cache [ 48.442443] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1) [ 48.443012] scsi host0: scsi_debug: version 0191 [20210520] [ 48.443012] dev_size_mb=100, opts=0x0, submit_queues=1, statistics=0 [ 48.444439] scsi 0:0:0:0: Direct-Access Linux scsi_debug 0191 PQ: 0 ANSI: 7 [ 48.445179] scsi 0:0:0:0: Power-on or device reset occurred [ 48.466111] sd 0:0:0:0: [sda] 204800 512-byte logical blocks: (105 MB/100 MiB) [ 48.470582] sd 0:0:0:0: [sda] Write Protect is off [ 48.478978] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA [ 48.503854] sd 0:0:0:0: [sda] permanent stream count = 5 [ 48.516603] sd 0:0:0:0: [sda] Preferred minimum I/O size 512 bytes [ 48.517127] sd 0:0:0:0: [sda] Optimal transfer size 524288 bytes [ 48.603781] sd 0:0:0:0: [sda] Attached SCSI disk [ 48.928371] sda: sda1 sda2 [ 50.835210] sd 0:0:0:0: [sda] Spinning up disk... [ 51.863595] .ready [ 51.956031] sda: sda1 sda2 [ 52.052811] sd 0:0:0:0: [sda] Synchronizing SCSI cache [ 52.275020] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1) [ 52.275575] scsi host0: scsi_debug: version 0191 [20210520] [ 52.275575] dev_size_mb=100, opts=0x0, submit_queues=1, statistics=0 [ 52.276874] scsi 0:0:0:0: Direct-Access Linux scsi_debug 0191 PQ: 0 ANSI: 7 [ 52.277546] scsi 0:0:0:0: Power-on or device reset occurred [ 52.298430] sd 0:0:0:0: [sda] 204800 512-byte logical blocks: (105 MB/100 MiB) [ 52.303120] sd 0:0:0:0: [sda] Write Protect is off [ 52.311522] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA [ 52.336493] sd 0:0:0:0: [sda] permanent stream count = 5 [ 52.348888] sd 0:0:0:0: [sda] Preferred minimum I/O size 512 bytes [ 52.349342] sd 0:0:0:0: [sda] Optimal transfer size 524288 bytes [ 52.447802] sd 0:0:0:0: [sda] Attached SCSI disk [ 52.768259] sda: sda1 sda2 [ 53.710987] EXT4-fs (sda1): mounting ext2 file system using the ext4 subsystem [ 53.724657] EXT4-fs (sda1): mounted filesystem 1a2875a2-82de-424d-9427-5e13e0653934 r/w without journal. Quota mode: disabled. [ 53.788294] EXT4-fs (sda2): mounting ext2 file system using the ext4 subsystem [ 53.801308] EXT4-fs (sda2): mounted filesystem 204b7606-d1ad-4952-b6ba-cefef6e27018 r/w without journal. Quota mode: disabled. [ 53.857674] EXT4-fs (sda2): unmounting filesystem 204b7606-d1ad-4952-b6ba-cefef6e27018. [ 53.913070] EXT4-fs (sda1): unmounting filesystem 1a2875a2-82de-424d-9427-5e13e0653934. [ 54.940261] sd 0:0:0:0: [sda] Spinning up disk... [ 55.959633] .ready [ 56.036569] sda: sda1 sda2 [ 56.080070] sd 0:0:0:0: [sda] Synchronizing SCSI cache [ 56.559946] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1) [ 56.560825] scsi host0: scsi_debug: version 0191 [20210520] [ 56.560825] dev_size_mb=50, opts=0x0, submit_queues=1, statistics=0 [ 56.562054] scsi 0:0:0:0: Direct-Access Linux scsi_debug 0191 PQ: 0 ANSI: 7 [ 56.562844] scsi 0:0:0:0: Power-on or device reset occurred [ 56.583738] sd 0:0:0:0: [sda] 102400 512-byte logical blocks: (52.4 MB/50.0 MiB) [ 56.584292] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 56.588773] sd 0:0:0:0: [sda] Write Protect is off [ 56.597199] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA [ 56.622149] sd 0:0:0:0: [sda] permanent stream count = 5 [ 56.634609] sd 0:0:0:0: [sda] Preferred minimum I/O size 4096 bytes [ 56.635137] sd 0:0:0:0: [sda] Optimal transfer size 524288 bytes [ 56.735784] sd 0:0:0:0: [sda] Attached SCSI disk [ 57.493060] sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 > [ 57.604500] sd 0:0:0:0: [sda] Synchronizing SCSI cache [ 57.826033] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1) [ 57.826872] scsi host0: scsi_debug: version 0191 [20210520] [ 57.826872] dev_size_mb=50, opts=0x0, submit_queues=1, statistics=0 [ 57.827897] scsi 0:0:0:0: Direct-Access Linux scsi_debug 0191 PQ: 0 ANSI: 7 [ 57.828460] scsi 0:0:0:0: Power-on or device reset occurred [ 57.849854] sd 0:0:0:0: [sda] physical block alignment offset: 3584 [ 57.850226] sd 0:0:0:0: [sda] 102400 512-byte logical blocks: (52.4 MB/50.0 MiB) [ 57.850833] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 57.855300] sd 0:0:0:0: [sda] Write Protect is off [ 57.863722] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA [ 57.888599] sd 0:0:0:0: [sda] permanent stream count = 5 [ 57.901094] sd 0:0:0:0: [sda] Preferred minimum I/O size 4096 bytes [ 57.901641] sd 0:0:0:0: [sda] Optimal transfer size 524288 bytes [ 57.983900] sd 0:0:0:0: [sda] Attached SCSI disk [ 58.801480] sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 > [ 58.916036] sd 0:0:0:0: [sda] Synchronizing SCSI cache [ 59.176009] loop0: detected capacity change from 0 to 102400 [ 59.332601] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1) [ 59.333485] scsi host0: scsi_debug: version 0191 [20210520] [ 59.333485] dev_size_mb=50, opts=0x0, submit_queues=1, statistics=0 [ 59.334709] scsi 0:0:0:0: Direct-Access Linux scsi_debug 0191 PQ: 0 ANSI: 7 [ 59.335395] scsi 0:0:0:0: Power-on or device reset occurred [ 59.356429] sd 0:0:0:0: [sda] 102400 512-byte logical blocks: (52.4 MB/50.0 MiB) [ 59.361198] sd 0:0:0:0: [sda] Write Protect is off [ 59.369840] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA [ 59.394578] sd 0:0:0:0: [sda] permanent stream count = 5 [ 59.407014] sd 0:0:0:0: [sda] Preferred minimum I/O size 512 bytes [ 59.407342] sd 0:0:0:0: [sda] Optimal transfer size 524288 bytes [ 59.499779] sd 0:0:0:0: [sda] Attached SCSI disk [ 60.303194] sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 > [ 60.432090] sd 0:0:0:0: [sda] Synchronizing SCSI cache [ 61.533705] loop0: detected capacity change from 0 to 20480 [ 61.573607] loop0: detected capacity change from 20480 to 40960 [ 61.605122] loop0: p1 p2 [ 68.510383] loop0: detected capacity change from 0 to 10240 [ 68.532824] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 68.535321] EXT4-fs (loop0): mounted filesystem 40127235-c779-4a8d-ac16-cd720569820e r/w without journal. Quota mode: disabled. [ 68.543523] EXT4-fs (loop0): unmounting filesystem 40127235-c779-4a8d-ac16-cd720569820e. [ 69.795320] NET: Registered PF_ALG protocol family [ 75.730039] loop0: detected capacity change from 0 to 20480 [ 75.730723] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 75.733056] EXT4-fs (loop0): mounted filesystem 6b838dcf-dff9-4c46-a06e-117f46812f7a r/w without journal. Quota mode: disabled. [ 75.737934] EXT4-fs (loop0): unmounting filesystem 6b838dcf-dff9-4c46-a06e-117f46812f7a. [ 75.769819] loop0: detected capacity change from 0 to 20480 [ 75.773598] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 75.775945] EXT4-fs (loop0): mounted filesystem 6b838dcf-dff9-4c46-a06e-117f46812f7a r/w without journal. Quota mode: disabled. [ 75.785237] EXT4-fs (loop0): unmounting filesystem 6b838dcf-dff9-4c46-a06e-117f46812f7a. [ 75.812227] loop0: detected capacity change from 0 to 20480 [ 75.817457] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 75.819612] EXT4-fs (loop0): mounted filesystem 6b838dcf-dff9-4c46-a06e-117f46812f7a r/w without journal. Quota mode: disabled. [ 75.828285] EXT4-fs (loop0): unmounting filesystem 6b838dcf-dff9-4c46-a06e-117f46812f7a. [ 75.858134] loop0: detected capacity change from 0 to 20480 [ 75.861330] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 75.863249] EXT4-fs (loop0): mounted filesystem 6b838dcf-dff9-4c46-a06e-117f46812f7a r/w without journal. Quota mode: disabled. [ 75.871905] EXT4-fs (loop0): unmounting filesystem 6b838dcf-dff9-4c46-a06e-117f46812f7a. [ 75.895437] loop0: detected capacity change from 0 to 20480 [ 75.900100] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 75.902342] EXT4-fs (loop0): mounted filesystem 6b838dcf-dff9-4c46-a06e-117f46812f7a r/w without journal. Quota mode: disabled. [ 75.910748] EXT4-fs (loop0): unmounting filesystem 6b838dcf-dff9-4c46-a06e-117f46812f7a. [ 75.938195] loop0: detected capacity change from 0 to 20478 [ 75.967660] loop0: detected capacity change from 0 to 20480 [ 75.997686] loop0: detected capacity change from 0 to 20480 [ 76.028291] loop0: detected capacity change from 0 to 20480 [ 76.028997] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 76.031749] EXT4-fs (loop0): mounted filesystem 6b838dcf-dff9-4c46-a06e-117f46812f7a r/w without journal. Quota mode: disabled. [ 76.041620] EXT4-fs (loop0): unmounting filesystem 6b838dcf-dff9-4c46-a06e-117f46812f7a. [ 76.181571] loop0: detected capacity change from 0 to 20480 [ 76.185307] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 76.187649] EXT4-fs (loop0): mounted filesystem 1585d324-8635-4308-ba4e-9bba084e3da6 r/w without journal. Quota mode: disabled. [ 76.196354] EXT4-fs (loop0): unmounting filesystem 1585d324-8635-4308-ba4e-9bba084e3da6. [ 76.207533] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 76.209992] EXT4-fs (loop0): mounted filesystem 1585d324-8635-4308-ba4e-9bba084e3da6 r/w without journal. Quota mode: disabled. [ 76.217096] EXT4-fs (loop1): mounting ext2 file system using the ext4 subsystem [ 76.219136] EXT4-fs (loop1): mounted filesystem 1585d324-8635-4308-ba4e-9bba084e3da6 r/w without journal. Quota mode: disabled. [ 76.224198] EXT4-fs (loop0): unmounting filesystem 1585d324-8635-4308-ba4e-9bba084e3da6. [ 76.230289] EXT4-fs (loop1): unmounting filesystem 1585d324-8635-4308-ba4e-9bba084e3da6. [ 83.506365] set_capacity_and_notify: 3 callbacks suppressed [ 83.506702] loop0: detected capacity change from 0 to 20480 [ 83.536752] loop0: detected capacity change from 0 to 18432 [ 83.563054] loop0: detected capacity change from 0 to 6144 [ 83.591284] loop0: detected capacity change from 0 to 6144 [ 83.722429] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1) [ 83.723222] scsi host0: scsi_debug: version 0191 [20210520] [ 83.723222] dev_size_mb=11, opts=0x0, submit_queues=1, statistics=0 [ 83.724367] scsi 0:0:0:0: Direct-Access Linux scsi_debug 0191 PQ: 0 ANSI: 7 [ 83.725193] scsi 0:0:0:0: Power-on or device reset occurred [ 83.746101] sd 0:0:0:0: [sda] 22528 512-byte logical blocks: (11.5 MB/11.0 MiB) [ 83.750588] sd 0:0:0:0: [sda] Write Protect is off [ 83.759007] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA [ 83.783933] sd 0:0:0:0: [sda] permanent stream count = 5 [ 83.796346] sd 0:0:0:0: [sda] Preferred minimum I/O size 512 bytes [ 83.796820] sd 0:0:0:0: [sda] Optimal transfer size 524288 bytes [ 83.883774] sd 0:0:0:0: [sda] Attached SCSI disk [ 83.901904] loop0: detected capacity change from 0 to 22528 [ 83.929887] loop0: detected capacity change from 0 to 20480 [ 83.958151] loop0: detected capacity change from 0 to 6144 [ 83.986601] loop0: detected capacity change from 0 to 6144 [ 84.084180] sd 0:0:0:0: [sda] Synchronizing SCSI cache [ 84.325846] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1) [ 84.326652] scsi host0: scsi_debug: version 0191 [20210520] [ 84.326652] dev_size_mb=11, opts=0x0, submit_queues=1, statistics=0 [ 84.327964] scsi 0:0:0:0: Direct-Access Linux scsi_debug 0191 PQ: 0 ANSI: 7 [ 84.328751] scsi 0:0:0:0: Power-on or device reset occurred [ 84.349717] sd 0:0:0:0: [sda] 22528 512-byte logical blocks: (11.5 MB/11.0 MiB) [ 84.354200] sd 0:0:0:0: [sda] Write Protect is off [ 84.362621] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA [ 84.387642] sd 0:0:0:0: [sda] permanent stream count = 5 [ 84.400365] sd 0:0:0:0: [sda] Preferred minimum I/O size 512 bytes [ 84.400784] sd 0:0:0:0: [sda] Optimal transfer size 524288 bytes [ 84.507796] sd 0:0:0:0: [sda] Attached SCSI disk [ 84.525470] loop0: detected capacity change from 0 to 22528 [ 84.529140] loop0: detected capacity change from 0 to 22528 [ 84.900043] sd 0:0:0:0: [sda] Synchronizing SCSI cache [ 90.659438] set_capacity_and_notify: 10 callbacks suppressed [ 90.659888] loop0: detected capacity change from 0 to 223232 [ 90.660866] BTRFS: device fsid c3f83729-11b9-44a2-a06f-727a30929c1e devid 1 transid 8 /dev/loop0 (7:0) scanned by mount (23412) [ 90.662186] BTRFS info (device loop0): first mount of filesystem c3f83729-11b9-44a2-a06f-727a30929c1e [ 90.662758] BTRFS info (device loop0): using crc32c (crc32c-lib) checksum algorithm [ 90.667951] BTRFS info (device loop0): checking UUID tree [ 90.668364] BTRFS info (device loop0): turning on async discard [ 90.668797] BTRFS info (device loop0): enabling free space tree [ 90.726428] BTRFS info (device loop0): last unmount of filesystem c3f83729-11b9-44a2-a06f-727a30929c1e [ 93.287197] loop0: detected capacity change from 0 to 223232 [ 93.287947] BTRFS: device fsid 889fef41-b21b-4d47-a0f8-901387282dc0 devid 1 transid 8 /dev/loop0 (7:0) scanned by mount (24666) [ 93.291487] BTRFS info (device loop0): first mount of filesystem 889fef41-b21b-4d47-a0f8-901387282dc0 [ 93.292157] BTRFS info (device loop0): using crc32c (crc32c-lib) checksum algorithm [ 93.296184] BTRFS info (device loop0): checking UUID tree [ 93.296659] BTRFS info (device loop0): turning on async discard [ 93.297098] BTRFS info (device loop0): enabling free space tree [ 93.393600] BTRFS info (device loop0): last unmount of filesystem 889fef41-b21b-4d47-a0f8-901387282dc0 [ 95.149681] loop0: detected capacity change from 0 to 10240 [ 96.626436] UDPLite: UDP-Lite is deprecated and scheduled to be removed in 2025, please contact the netdev mailing list [ 96.833836] UDPLite6: UDP-Lite is deprecated and scheduled to be removed in 2025, please contact the netdev mailing list [ 111.290116] loop0: detected capacity change from 0 to 10240 [ 111.338024] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 111.340436] EXT4-fs (loop0): mounted filesystem 6d293a84-15b2-4bb6-b7f2-ec77157ce3ba r/w without journal. Quota mode: disabled. [ 111.397073] EXT4-fs (loop0): re-mounted 6d293a84-15b2-4bb6-b7f2-ec77157ce3ba ro. [ 111.444859] EXT4-fs (loop0): re-mounted 6d293a84-15b2-4bb6-b7f2-ec77157ce3ba r/w. [ 111.494675] EXT4-fs (loop0): unmounting filesystem 6d293a84-15b2-4bb6-b7f2-ec77157ce3ba. [ 111.597071] loop0: detected capacity change from 0 to 10240 [ 111.619581] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 111.622061] EXT4-fs (loop0): mounted filesystem 06804864-2262-4deb-addd-ff81ef79f2ce r/w without journal. Quota mode: disabled. [ 111.632071] EXT4-fs (loop0): unmounting filesystem 06804864-2262-4deb-addd-ff81ef79f2ce. [ 111.853422] loop0: detected capacity change from 0 to 10240 [ 111.879465] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 111.881669] EXT4-fs (loop0): mounted filesystem c93711bf-4cba-4349-84ee-e0937d8843c7 r/w without journal. Quota mode: disabled. [ 111.892522] EXT4-fs (loop0): unmounting filesystem c93711bf-4cba-4349-84ee-e0937d8843c7. [ 111.917728] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 111.919960] EXT4-fs (loop0): mounted filesystem c93711bf-4cba-4349-84ee-e0937d8843c7 r/w without journal. Quota mode: disabled. [ 111.935436] EXT4-fs (loop0): unmounting filesystem c93711bf-4cba-4349-84ee-e0937d8843c7. [ 111.957043] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 111.959502] EXT4-fs (loop0): mounted filesystem c93711bf-4cba-4349-84ee-e0937d8843c7 r/w without journal. Quota mode: disabled. [ 111.985193] EXT4-fs (loop0): re-mounted c93711bf-4cba-4349-84ee-e0937d8843c7 ro. [ 111.998720] EXT4-fs (loop0): unmounting filesystem c93711bf-4cba-4349-84ee-e0937d8843c7. [ 112.118226] loop0: detected capacity change from 0 to 10240 [ 112.142448] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 112.144909] EXT4-fs (loop0): mounted filesystem fc1cacbc-de41-4b1e-8275-2e69070aa0a8 r/w without journal. Quota mode: disabled. [ 112.153228] EXT4-fs (loop0): unmounting filesystem fc1cacbc-de41-4b1e-8275-2e69070aa0a8. [ 112.181765] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 112.183919] EXT4-fs (loop0): mounted filesystem fc1cacbc-de41-4b1e-8275-2e69070aa0a8 r/w without journal. Quota mode: disabled. [ 112.192794] EXT4-fs (loop0): unmounting filesystem fc1cacbc-de41-4b1e-8275-2e69070aa0a8. [ 112.232036] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 112.233832] EXT4-fs (loop0): mounted filesystem fc1cacbc-de41-4b1e-8275-2e69070aa0a8 r/w without journal. Quota mode: disabled. [ 112.247923] EXT4-fs (loop0): unmounting filesystem fc1cacbc-de41-4b1e-8275-2e69070aa0a8. [ 112.267968] EXT4-fs (loop0): couldn't mount as ext3 due to feature incompatibilities [ 112.268601] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 112.270935] EXT4-fs (loop0): mounted filesystem fc1cacbc-de41-4b1e-8275-2e69070aa0a8 r/w without journal. Quota mode: disabled. [ 112.282375] EXT4-fs (loop0): unmounting filesystem fc1cacbc-de41-4b1e-8275-2e69070aa0a8. [ 112.303412] EXT4-fs (loop0): couldn't mount as ext3 due to feature incompatibilities [ 112.304219] FAT-fs (loop0): bogus number of reserved sectors [ 112.304626] FAT-fs (loop0): Can't find a valid FAT filesystem [ 112.441830] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1) [ 112.442609] scsi host0: scsi_debug: version 0191 [20210520] [ 112.442609] dev_size_mb=50, opts=0x0, submit_queues=1, statistics=0 [ 112.443984] scsi 0:0:0:0: Direct-Access Linux scsi_debug 0191 PQ: 0 ANSI: 7 [ 112.444661] scsi 0:0:0:0: Power-on or device reset occurred [ 112.465860] sd 0:0:0:0: [sda] 102400 512-byte logical blocks: (52.4 MB/50.0 MiB) [ 112.470508] sd 0:0:0:0: [sda] Write Protect is off [ 112.478897] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA [ 112.503709] sd 0:0:0:0: [sda] permanent stream count = 5 [ 112.516113] sd 0:0:0:0: [sda] Preferred minimum I/O size 512 bytes [ 112.516464] sd 0:0:0:0: [sda] Optimal transfer size 524288 bytes [ 112.599737] sd 0:0:0:0: [sda] Attached SCSI disk [ 113.200645] sda: sda1 sda2 sda3 sda4 [ 114.149848] EXT4-fs (sda1): mounting ext2 file system using the ext4 subsystem [ 114.163376] EXT4-fs (sda1): mounted filesystem 57eff9ba-1792-4d55-a916-5e58a54e395e r/w without journal. Quota mode: disabled. [ 114.168549] EXT4-fs (sda2): mounting ext2 file system using the ext4 subsystem [ 114.181839] EXT4-fs (sda2): mounted filesystem e726ceba-3a0e-4b03-9fcc-0a8758531f35 r/w without journal. Quota mode: disabled. [ 114.187048] EXT4-fs (sda3): mounting ext2 file system using the ext4 subsystem [ 114.196343] EXT4-fs (sda3): mounted filesystem f1760053-5b05-4461-a14f-580bb7b5ae87 ro without journal. Quota mode: disabled. [ 114.348650] EXT4-fs (sda4): mounted filesystem 60e9669b-c47e-4fb3-925c-34b37824e4d6 r/w with ordered data mode. Quota mode: disabled. [ 114.403351] EXT4-fs (sda1): unmounting filesystem 57eff9ba-1792-4d55-a916-5e58a54e395e. [ 114.456652] EXT4-fs (sda2): unmounting filesystem e726ceba-3a0e-4b03-9fcc-0a8758531f35. [ 114.462056] EXT4-fs (sda3): unmounting filesystem f1760053-5b05-4461-a14f-580bb7b5ae87. [ 114.514404] EXT4-fs (sda4): unmounting filesystem 60e9669b-c47e-4fb3-925c-34b37824e4d6. [ 114.687157] EXT4-fs (sda4): mounted filesystem 60e9669b-c47e-4fb3-925c-34b37824e4d6 r/w with ordered data mode. Quota mode: disabled. [ 114.741867] EXT4-fs (sda4): unmounting filesystem 60e9669b-c47e-4fb3-925c-34b37824e4d6. [ 114.769107] EXT4-fs (sda1): mounting ext2 file system using the ext4 subsystem [ 114.782230] EXT4-fs (sda1): mounted filesystem 57eff9ba-1792-4d55-a916-5e58a54e395e r/w without journal. Quota mode: disabled. [ 114.787471] EXT4-fs (sda2): mounting ext2 file system using the ext4 subsystem [ 114.800543] EXT4-fs (sda2): mounted filesystem e726ceba-3a0e-4b03-9fcc-0a8758531f35 r/w without journal. Quota mode: disabled. [ 114.805892] EXT4-fs (sda3): mounting ext2 file system using the ext4 subsystem [ 114.814760] EXT4-fs (sda3): mounted filesystem f1760053-5b05-4461-a14f-580bb7b5ae87 ro without journal. Quota mode: disabled. [ 114.869240] EXT4-fs (sda1): unmounting filesystem 57eff9ba-1792-4d55-a916-5e58a54e395e. [ 114.922818] EXT4-fs (sda2): unmounting filesystem e726ceba-3a0e-4b03-9fcc-0a8758531f35. [ 114.928092] EXT4-fs (sda3): unmounting filesystem f1760053-5b05-4461-a14f-580bb7b5ae87. [ 114.950644] EXT4-fs (sda3): mounting ext2 file system using the ext4 subsystem [ 114.959780] EXT4-fs (sda3): mounted filesystem f1760053-5b05-4461-a14f-580bb7b5ae87 ro without journal. Quota mode: disabled. [ 114.966131] EXT4-fs (sda3): unmounting filesystem f1760053-5b05-4461-a14f-580bb7b5ae87. [ 114.992667] EXT4-fs (sda1): mounting ext2 file system using the ext4 subsystem [ 115.001730] EXT4-fs (sda1): mounted filesystem 57eff9ba-1792-4d55-a916-5e58a54e395e ro without journal. Quota mode: disabled. [ 115.006621] EXT4-fs (sda2): mounting ext2 file system using the ext4 subsystem [ 115.015782] EXT4-fs (sda2): mounted filesystem e726ceba-3a0e-4b03-9fcc-0a8758531f35 ro without journal. Quota mode: disabled. [ 115.020975] EXT4-fs (sda3): mounting ext2 file system using the ext4 subsystem [ 115.030066] EXT4-fs (sda3): mounted filesystem f1760053-5b05-4461-a14f-580bb7b5ae87 ro without journal. Quota mode: disabled. [ 115.177573] EXT4-fs (sda4): orphan cleanup on readonly fs [ 115.178296] EXT4-fs (sda4): mounted filesystem 60e9669b-c47e-4fb3-925c-34b37824e4d6 ro with ordered data mode. Quota mode: disabled. [ 115.186722] EXT4-fs (sda1): unmounting filesystem 57eff9ba-1792-4d55-a916-5e58a54e395e. [ 115.191443] EXT4-fs (sda2): unmounting filesystem e726ceba-3a0e-4b03-9fcc-0a8758531f35. [ 115.196451] EXT4-fs (sda3): unmounting filesystem f1760053-5b05-4461-a14f-580bb7b5ae87. [ 115.200779] EXT4-fs (sda4): unmounting filesystem 60e9669b-c47e-4fb3-925c-34b37824e4d6. [ 115.225045] EXT4-fs (sda1): mounting ext2 file system using the ext4 subsystem [ 115.238152] EXT4-fs (sda1): mounted filesystem 57eff9ba-1792-4d55-a916-5e58a54e395e r/w without journal. Quota mode: disabled. [ 115.243289] EXT4-fs (sda2): mounting ext2 file system using the ext4 subsystem [ 115.256351] EXT4-fs (sda2): mounted filesystem e726ceba-3a0e-4b03-9fcc-0a8758531f35 r/w without journal. Quota mode: disabled. [ 115.261360] EXT4-fs (sda3): mounting ext2 file system using the ext4 subsystem [ 115.270501] EXT4-fs (sda3): mounted filesystem f1760053-5b05-4461-a14f-580bb7b5ae87 ro without journal. Quota mode: disabled. [ 115.422042] EXT4-fs (sda4): mounted filesystem 60e9669b-c47e-4fb3-925c-34b37824e4d6 r/w with ordered data mode. Quota mode: disabled. [ 115.477121] EXT4-fs (sda1): unmounting filesystem 57eff9ba-1792-4d55-a916-5e58a54e395e. [ 115.530370] EXT4-fs (sda2): unmounting filesystem e726ceba-3a0e-4b03-9fcc-0a8758531f35. [ 115.535604] EXT4-fs (sda3): unmounting filesystem f1760053-5b05-4461-a14f-580bb7b5ae87. [ 115.588214] EXT4-fs (sda4): unmounting filesystem 60e9669b-c47e-4fb3-925c-34b37824e4d6. [ 115.619057] EXT4-fs (sda1): mounting ext2 file system using the ext4 subsystem [ 115.632230] EXT4-fs (sda1): mounted filesystem 57eff9ba-1792-4d55-a916-5e58a54e395e r/w without journal. Quota mode: disabled. [ 115.637726] EXT4-fs (sda2): mounting ext2 file system using the ext4 subsystem [ 115.650851] EXT4-fs (sda2): mounted filesystem e726ceba-3a0e-4b03-9fcc-0a8758531f35 r/w without journal. Quota mode: disabled. [ 115.656277] EXT4-fs (sda3): mounting ext2 file system using the ext4 subsystem [ 115.669491] EXT4-fs (sda3): mounted filesystem f1760053-5b05-4461-a14f-580bb7b5ae87 r/w without journal. Quota mode: disabled. [ 115.821772] EXT4-fs (sda4): mounted filesystem 60e9669b-c47e-4fb3-925c-34b37824e4d6 r/w with ordered data mode. Quota mode: disabled. [ 115.877238] EXT4-fs (sda1): unmounting filesystem 57eff9ba-1792-4d55-a916-5e58a54e395e. [ 115.930770] EXT4-fs (sda2): unmounting filesystem e726ceba-3a0e-4b03-9fcc-0a8758531f35. [ 115.984109] EXT4-fs (sda3): unmounting filesystem f1760053-5b05-4461-a14f-580bb7b5ae87. [ 116.037308] EXT4-fs (sda4): unmounting filesystem 60e9669b-c47e-4fb3-925c-34b37824e4d6. [ 116.104039] sd 0:0:0:0: [sda] Synchronizing SCSI cache [ 116.627684] loop0: detected capacity change from 0 to 102400 [ 116.685099] loop1: detected capacity change from 0 to 102400 [ 116.690014] BTRFS: device fsid 8d6a91f5-d61a-457a-a92b-43d29ae3b4f4 devid 1 transid 8 /dev/loop1 (7:1) scanned by mount (31894) [ 116.691386] BTRFS info (device loop1): first mount of filesystem 8d6a91f5-d61a-457a-a92b-43d29ae3b4f4 [ 116.692132] BTRFS info (device loop1): using crc32c (crc32c-lib) checksum algorithm [ 116.695961] BTRFS info (device loop1): checking UUID tree [ 116.696347] BTRFS info (device loop1): turning on async discard [ 116.696642] BTRFS info (device loop1): enabling free space tree [ 116.713691] BTRFS info (device loop1): setting incompat feature flag for DEFAULT_SUBVOL (0x2) [ 116.728773] BTRFS info (device loop1): last unmount of filesystem 8d6a91f5-d61a-457a-a92b-43d29ae3b4f4 [ 116.750864] BTRFS: device fsid 8d6a91f5-d61a-457a-a92b-43d29ae3b4f4 devid 1 transid 9 /dev/loop0 (7:0) scanned by mount (31935) [ 116.752127] BTRFS info (device loop0): first mount of filesystem 8d6a91f5-d61a-457a-a92b-43d29ae3b4f4 [ 116.752727] BTRFS info (device loop0): using crc32c (crc32c-lib) checksum algorithm [ 116.755025] BTRFS info (device loop0): turning on async discard [ 116.755460] BTRFS info (device loop0): enabling free space tree [ 116.777226] BTRFS info (device loop0): last unmount of filesystem 8d6a91f5-d61a-457a-a92b-43d29ae3b4f4 [ 116.821314] BTRFS: device fsid 8d6a91f5-d61a-457a-a92b-43d29ae3b4f4 devid 1 transid 9 /dev/loop0 (7:0) scanned by mount (31977) [ 116.827899] BTRFS info (device loop0): first mount of filesystem 8d6a91f5-d61a-457a-a92b-43d29ae3b4f4 [ 116.828768] BTRFS info (device loop0): using crc32c (crc32c-lib) checksum algorithm [ 116.831040] BTRFS info (device loop0): turning on async discard [ 116.831463] BTRFS info (device loop0): enabling free space tree [ 116.850882] BTRFS info (device loop0): last unmount of filesystem 8d6a91f5-d61a-457a-a92b-43d29ae3b4f4 [ 116.976496] loop0: detected capacity change from 0 to 10240 [ 117.011307] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 117.013264] EXT4-fs (loop0): mounted filesystem 51482507-820a-4d5c-bd01-7b45465a9c22 r/w without journal. Quota mode: disabled. [ 117.022709] EXT4-fs (loop0): unmounting filesystem 51482507-820a-4d5c-bd01-7b45465a9c22. [ 117.046840] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 117.049292] EXT4-fs (loop0): mounted filesystem 51482507-820a-4d5c-bd01-7b45465a9c22 r/w without journal. Quota mode: disabled. [ 117.057931] EXT4-fs (loop0): unmounting filesystem 51482507-820a-4d5c-bd01-7b45465a9c22. [ 117.177366] loop0: detected capacity change from 0 to 10240 [ 117.212415] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 117.329117] loop0: detected capacity change from 0 to 10240 [ 117.365803] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 117.480144] loop0: detected capacity change from 0 to 10240 [ 117.543269] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 117.575464] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 117.606751] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 117.725247] loop0: detected capacity change from 0 to 10240 [ 117.786778] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 117.819281] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 117.948250] loop0: detected capacity change from 0 to 10240 [ 118.017068] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 118.049378] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 118.193191] loop0: detected capacity change from 0 to 10240 [ 118.194005] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 118.419529] loop0: detected capacity change from 0 to 10240 [ 118.455698] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 118.635034] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 118.667749] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 118.699060] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 118.877839] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 118.907443] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 119.087120] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 119.117001] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 119.295491] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 119.329300] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 119.606202] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 119.731394] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 119.781290] EXT4-fs (loop0): re-mounted 74a64928-9d1a-4a4d-b383-d59208899ee4 ro. [ 119.924375] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 119.936280] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 119.950337] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 119.963701] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 119.976745] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 119.989614] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 120.246705] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 120.276296] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 120.650902] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 120.684590] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 120.832512] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1) [ 120.833409] scsi host0: scsi_debug: version 0191 [20210520] [ 120.833409] dev_size_mb=50, opts=0x0, submit_queues=1, statistics=0 [ 120.834578] scsi 0:0:0:0: Direct-Access Linux scsi_debug 0191 PQ: 0 ANSI: 7 [ 120.835266] scsi 0:0:0:0: Power-on or device reset occurred [ 120.856240] sd 0:0:0:0: [sda] 102400 512-byte logical blocks: (52.4 MB/50.0 MiB) [ 120.860813] sd 0:0:0:0: [sda] Write Protect is off [ 120.869221] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA [ 120.893960] sd 0:0:0:0: [sda] permanent stream count = 5 [ 120.906406] sd 0:0:0:0: [sda] Preferred minimum I/O size 512 bytes [ 120.906779] sd 0:0:0:0: [sda] Optimal transfer size 524288 bytes [ 120.999754] sd 0:0:0:0: [sda] Attached SCSI disk [ 121.572834] sda: sda1 sda2 sda3 sda4 [ 122.498666] EXT4-fs (sda1): mounting ext2 file system using the ext4 subsystem [ 122.730263] EXT4-fs (sda1): mounting ext2 file system using the ext4 subsystem [ 122.966983] EXT4-fs (sda1): mounting ext2 file system using the ext4 subsystem [ 123.132164] EXT4-fs (sda2): mounting ext2 file system using the ext4 subsystem [ 123.222353] EXT4-fs (sda3): mounting ext2 file system using the ext4 subsystem [ 123.295986] EXT4-fs (sda4): mounting ext2 file system using the ext4 subsystem [ 123.584184] sd 0:0:0:0: [sda] Synchronizing SCSI cache [ 123.868413] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1) [ 123.870176] scsi host0: scsi_debug: version 0191 [20210520] [ 123.870176] dev_size_mb=50, opts=0x0, submit_queues=1, statistics=0 [ 123.871195] scsi 0:0:0:0: Direct-Access Linux scsi_debug 0191 PQ: 0 ANSI: 7 [ 123.871866] scsi 0:0:0:0: Power-on or device reset occurred [ 123.892948] sd 0:0:0:0: [sda] 102400 512-byte logical blocks: (52.4 MB/50.0 MiB) [ 123.897463] sd 0:0:0:0: [sda] Write Protect is off [ 123.905905] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA [ 123.930963] sd 0:0:0:0: [sda] permanent stream count = 5 [ 123.943450] sd 0:0:0:0: [sda] Preferred minimum I/O size 512 bytes [ 123.943826] sd 0:0:0:0: [sda] Optimal transfer size 524288 bytes [ 124.039815] sd 0:0:0:0: [sda] Attached SCSI disk [ 124.621473] sda: sda1 sda2 sda3 sda4 [ 125.541432] EXT4-fs (sda1): mounting ext2 file system using the ext4 subsystem [ 125.634409] EXT4-fs (sda2): mounting ext2 file system using the ext4 subsystem [ 125.724610] EXT4-fs (sda3): mounting ext2 file system using the ext4 subsystem [ 125.796467] EXT4-fs (sda4): mounting ext2 file system using the ext4 subsystem [ 126.128180] sd 0:0:0:0: [sda] Synchronizing SCSI cache [ 126.447969] set_capacity_and_notify: 9 callbacks suppressed [ 126.448331] loop0: detected capacity change from 0 to 10240 [ 126.503884] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 126.536485] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem [ 126.980980] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1) [ 126.981550] scsi host0: scsi_debug: version 0191 [20210520] [ 126.981550] dev_size_mb=50, opts=0x0, submit_queues=1, statistics=0 [ 126.983864] scsi 0:0:0:0: Direct-Access Linux scsi_debug 0191 PQ: 0 ANSI: 7 [ 126.984453] scsi 0:0:0:0: Power-on or device reset occurred [ 127.008310] sd 0:0:0:0: [sda] 102400 512-byte logical blocks: (52.4 MB/50.0 MiB) [ 127.012755] sd 0:0:0:0: [sda] Write Protect is off [ 127.021190] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA [ 127.046079] sd 0:0:0:0: [sda] permanent stream count = 5 [ 127.059036] sd 0:0:0:0: [sda] Preferred minimum I/O size 512 bytes [ 127.059415] sd 0:0:0:0: [sda] Optimal transfer size 524288 bytes [ 127.143786] sd 0:0:0:0: [sda] Attached SCSI disk [ 127.852373] sda: sda1 sda2 sda3 [ 128.172177] sd 0:0:0:0: [sda] Synchronizing SCSI cache [ 155.308794] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1) [ 155.309623] scsi host0: scsi_debug: version 0191 [20210520] [ 155.309623] dev_size_mb=50, opts=0x0, submit_queues=1, statistics=0 [ 155.310660] scsi 0:0:0:0: Direct-Access Linux scsi_debug 0191 PQ: 0 ANSI: 7 [ 155.311367] scsi 0:0:0:0: Power-on or device reset occurred [ 155.332317] sd 0:0:0:0: [sda] 102400 512-byte logical blocks: (52.4 MB/50.0 MiB) [ 155.333708] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 155.338156] sd 0:0:0:0: [sda] Write Protect is off [ 155.346569] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA [ 155.371367] sd 0:0:0:0: [sda] permanent stream count = 5 [ 155.383884] sd 0:0:0:0: [sda] Preferred minimum I/O size 4096 bytes [ 155.384714] sd 0:0:0:0: [sda] Optimal transfer size 524288 bytes [ 155.471786] sd 0:0:0:0: [sda] Attached SCSI disk [ 156.277212] sda: sda1 sda2 sda3 sda4 < sda5 sda6 > [ 156.788746] sda: sda1 sda2 sda3 sda4 < sda5 sda6 > [ 157.928363] sda: sda1 sda2 sda3 [ 158.968663] sda: sda1 [ 160.268841] sda: sda1 sda2 sda3 sda4 < sda5 sda6 > [ 161.636991] sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 > [ 162.688284] sda: sda1 [ 163.164269] sda: sda1 [ 164.220410] sda: sda1 sda2 < > [ 164.690468] sda: sda1 sda2 < > [ 165.752875] sda: sda1 sda2 < > [ 166.232415] sda: sda1 sda2 < > [ 167.473421] sda: sda1 sda2 sda3 sda4 < sda5 sda6 > [ 167.961350] sda: sda1 sda2 sda3 sda4 < sda5 sda6 > [ 169.200685] sda: sda1 sda2 sda3 sda4 < sda5 sda6 > [ 169.680858] sda: sda1 sda2 sda3 sda4 < sda5 sda6 > [ 170.720477] sda: sda1 [ 171.864408] sda: sda1 sda3 [ 173.004464] sda: sda1 sda2 [ 174.280576] sda: sda1 sda2 sda3 sda4 [ 175.392284] sda: sda1 sda2 sda3 [ 175.508130] sd 0:0:0:0: [sda] Synchronizing SCSI cache [ 175.737004] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1) [ 175.737759] scsi host0: scsi_debug: version 0191 [20210520] [ 175.737759] dev_size_mb=100, opts=0x0, submit_queues=1, statistics=0 [ 175.739021] scsi 0:0:0:0: Direct-Access Linux scsi_debug 0191 PQ: 0 ANSI: 7 [ 175.739852] scsi 0:0:0:0: Power-on or device reset occurred [ 175.760726] sd 0:0:0:0: [sda] 204800 512-byte logical blocks: (105 MB/100 MiB) [ 175.761424] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 175.765834] sd 0:0:0:0: [sda] Write Protect is off [ 175.774284] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA [ 175.799274] sd 0:0:0:0: [sda] permanent stream count = 5 [ 175.811696] sd 0:0:0:0: [sda] Preferred minimum I/O size 4096 bytes [ 175.813055] sd 0:0:0:0: [sda] Optimal transfer size 524288 bytes [ 175.895915] sd 0:0:0:0: [sda] Attached SCSI disk [ 177.061624] sda: sda1 sda2 sda3 sda4 [ 178.753385] sda: sda1 sda2 sda3 sda4 [ 180.562304] sda: sda1 sda2 sda3 sda4 [ 180.660793] sd 0:0:0:0: [sda] Synchronizing SCSI cache [ 180.872518] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1) [ 180.873939] scsi host0: scsi_debug: version 0191 [20210520] [ 180.873939] dev_size_mb=50, opts=0x0, submit_queues=1, statistics=0 [ 180.875776] scsi 0:0:0:0: Direct-Access Linux scsi_debug 0191 PQ: 0 ANSI: 7 [ 180.877476] scsi 0:0:0:0: Power-on or device reset occurred [ 180.899625] sd 0:0:0:0: [sda] 102400 512-byte logical blocks: (52.4 MB/50.0 MiB) [ 180.900296] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 180.904683] sd 0:0:0:0: [sda] Write Protect is off [ 180.913704] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA [ 180.938860] sd 0:0:0:0: [sda] permanent stream count = 5 [ 180.951421] sd 0:0:0:0: [sda] Preferred minimum I/O size 4096 bytes [ 180.951823] sd 0:0:0:0: [sda] Optimal transfer size 524288 bytes [ 181.043756] sd 0:0:0:0: [sda] Attached SCSI disk [ 182.231251] sda: sda1 sda2 sda3 sda4 sda5 [ 182.925119] sda: sda1 sda2 sda3 sda4 sda5 [ 183.586309] sda: sda1 sda2 sda3 sda4 sda5 [ 184.248653] sda: sda1 sda2 sda3 sda4 sda5 [ 184.917771] sda: sda1 sda2 sda3 sda4 sda5 [ 185.585750] sda: sda1 sda2 sda3 sda4 sda5 [ 186.361939] sda: sda1 sda2 sda3 sda4 sda5 [ 187.141602] sda: sda1 sda2 sda3 sda4 sda5 [ 187.913217] sda: sda1 sda2 sda3 sda4 sda5 [ 188.776889] sda: sda1 sda2 sda3 sda4 sda5 [ 189.649819] sda: sda1 sda2 sda3 sda4 sda5 [ 190.521341] sda: sda1 sda2 sda3 sda4 sda5 [ 192.593635] sda: sda1 sda2 sda3 sda4 [ 194.272950] sda: sda1 [ 194.946267] sda: sda1 [ 196.525074] sda: sda1 sda2 sda3 sda4 [ 197.188446] sda: sda1 sda2 sda3 sda4 [ 197.296137] sd 0:0:0:0: [sda] Synchronizing SCSI cache [ 197.540311] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1) [ 197.541112] scsi host0: scsi_debug: version 0191 [20210520] [ 197.541112] dev_size_mb=100, opts=0x0, submit_queues=1, statistics=0 [ 197.542049] scsi 0:0:0:0: Direct-Access Linux scsi_debug 0191 PQ: 0 ANSI: 7 [ 197.542765] scsi 0:0:0:0: Power-on or device reset occurred [ 197.564306] sd 0:0:0:0: [sda] 204800 512-byte logical blocks: (105 MB/100 MiB) [ 197.569697] sd 0:0:0:0: [sda] Write Protect is off [ 197.578226] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA [ 197.603731] sd 0:0:0:0: [sda] permanent stream count = 5 [ 197.616321] sd 0:0:0:0: [sda] Preferred minimum I/O size 512 bytes [ 197.616681] sd 0:0:0:0: [sda] Optimal transfer size 524288 bytes [ 197.704175] sd 0:0:0:0: [sda] Attached SCSI disk [ 198.237256] sda: sda1 [ 199.346772] sda: sda1 [ 200.209867] sda: sda1 [ 201.121900] sda: sda1 [ 201.360052] sd 0:0:0:0: [sda] Synchronizing SCSI cache [ 201.602370] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1) [ 201.603222] scsi host0: scsi_debug: version 0191 [20210520] [ 201.603222] dev_size_mb=100, opts=0x0, submit_queues=1, statistics=0 [ 201.604444] scsi 0:0:0:0: Direct-Access Linux scsi_debug 0191 PQ: 0 ANSI: 7 [ 201.605200] scsi 0:0:0:0: Power-on or device reset occurred [ 201.626205] sd 0:0:0:0: [sda] 204800 512-byte logical blocks: (105 MB/100 MiB) [ 201.630986] sd 0:0:0:0: [sda] Write Protect is off [ 201.639571] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA [ 201.664438] sd 0:0:0:0: [sda] permanent stream count = 5 [ 201.676868] sd 0:0:0:0: [sda] Preferred minimum I/O size 512 bytes [ 201.677276] sd 0:0:0:0: [sda] Optimal transfer size 524288 bytes [ 201.759781] sd 0:0:0:0: [sda] Attached SCSI disk [ 202.372687] sda: sda1 [ 202.856250] sda: sda1 [ 203.362701] sda: sda1 [ 203.866062] sda: sda1 [ 204.378648] sda: sda1 [ 204.897406] sda: sda1 [ 205.396828] sda: sda1 [ 205.904500] sda: sda1 [ 206.412683] sda: sda1 [ 206.924258] sda: sda1 [ 207.424869] sda: sda1 [ 207.920320] sda: sda1 [ 208.434271] sda: sda1 [ 209.028470] sda: sda1 sda2 [ 209.624562] sda: sda1 sda2 sda3 [ 210.100441] sda: sda1 sda2 sda3 [ 210.596514] sda: sda1 sda2 sda3 [ 211.932811] sda: sda1 [ 212.628298] sda: sda1 [ 213.330030] sda: sda1 [ 214.025022] sda: sda1 [ 214.719384] sda: sda1 [ 215.420887] sda: sda1 [ 216.117251] sda: sda1 [ 216.813572] sda: sda1 [ 217.520959] sda: sda1 [ 218.212752] sda: sda1 [ 218.912894] sda: sda1 [ 219.621340] sda: sda1 [ 220.321277] sda: sda1 [ 221.117109] sda: sda1 sda2 [ 221.889324] sda: sda1 sda2 sda3 [ 222.574727] sda: sda1 sda2 sda3 [ 223.282674] sda: sda1 sda2 sda3 [ 224.564795] sda: sda1 sda2 sda3 < sda5 sda6 > sda4 [ 225.068845] sda: sda1 sda2 sda3 < sda5 sda6 > sda4 [ 225.208918] sd 0:0:0:0: [sda] Synchronizing SCSI cache [ 225.412455] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1) [ 225.417568] scsi host0: scsi_debug: version 0191 [20210520] [ 225.417568] dev_size_mb=50, opts=0x0, submit_queues=1, statistics=0 [ 225.419669] scsi 0:0:0:0: Direct-Access Linux scsi_debug 0191 PQ: 0 ANSI: 7 [ 225.420553] scsi 0:0:0:0: Power-on or device reset occurred [ 225.441406] sd 0:0:0:0: [sda] 102400 512-byte logical blocks: (52.4 MB/50.0 MiB) [ 225.441920] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 225.449504] sd 0:0:0:0: [sda] Write Protect is off [ 225.457930] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA [ 225.487576] sd 0:0:0:0: [sda] permanent stream count = 5 [ 225.500621] sd 0:0:0:0: [sda] Preferred minimum I/O size 4096 bytes [ 225.501041] sd 0:0:0:0: [sda] Optimal transfer size 524288 bytes [ 225.591798] sd 0:0:0:0: [sda] Attached SCSI disk [ 226.665024] sda: sda1 sda2 sda3 sda4 [ 228.265414] sda: sda1 sda2 sda3 sda4 [ 229.901098] sda: sda1 sda2 sda3 sda4 [ 231.428015] sd 0:0:0:0: [sda] Synchronizing SCSI cache [ 231.696201] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1) [ 231.697346] scsi host0: scsi_debug: version 0191 [20210520] [ 231.697346] dev_size_mb=50, opts=0x0, submit_queues=1, statistics=0 [ 231.699209] scsi 0:0:0:0: Direct-Access Linux scsi_debug 0191 PQ: 0 ANSI: 7 [ 231.700518] scsi 0:0:0:0: Power-on or device reset occurred [ 231.721478] sd 0:0:0:0: [sda] 102400 512-byte logical blocks: (52.4 MB/50.0 MiB) [ 231.722100] sd 0:0:0:0: [sda] 4096-byte physical blocks [ 231.727257] sd 0:0:0:0: [sda] Write Protect is off [ 231.736399] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA [ 231.762140] sd 0:0:0:0: [sda] permanent stream count = 5 [ 231.774668] sd 0:0:0:0: [sda] Preferred minimum I/O size 4096 bytes [ 231.775289] sd 0:0:0:0: [sda] Optimal transfer size 524288 bytes [ 231.867795] sd 0:0:0:0: [sda] Attached SCSI disk [ 235.880734] sda: sda1 [ 237.421098] sda: sda1 [ 237.635978] sd 0:0:0:0: [sda] Synchronizing SCSI cache [ 237.929948] loop0: detected capacity change from 0 to 10240 [ 237.949305] Adding 5116k swap on /dev/loop0. Priority:-2 extents:1 across:5116k [ 238.070843] loop0: detected capacity change from 0 to 10240 [ 238.100290] Adding 5116k swap on /dev/loop0. Priority:-2 extents:1 across:5116k [ 238.231037] loop0: detected capacity change from 0 to 10240 [ 238.267407] Adding 5116k swap on /dev/loop0. Priority:-2 extents:1 across:5116k [ 238.386014] loop0: detected capacity change from 0 to 10240 [ 238.429961] Adding 5116k swap on /dev/loop0. Priority:-2 extents:1 across:5116k [ 238.552032] loop0: detected capacity change from 0 to 10240 [ 238.598412] Adding 5116k swap on /dev/loop0. Priority:-2 extents:1 across:5116k [ 250.522113] udevd[9441]: starting version 3.2.14 [ 250.527102] udevd[9442]: starting eudev-3.2.14