[    0.000000] Linux version 6.18.48-yocto-standard (oe-user@oe-host) (x86_64-poky-linux-gcc (GCC) 16.2.0, GNU ld (GNU Binutils) 2.47.20260726) #1 SMP PREEMPT_DYNAMIC Tue Sep  1 21:35:47 UTC 2026
[    0.000000] Command line: root=/dev/vda rw  ip=192.168.7.28::192.168.7.27:255.255.255.0::eth0:off:8.8.8.8 net.ifnames=0 console=ttyS0 console=ttyS1 oprofile.timer=1 tsc=reliable no_timer_check rcupdate.rcu_expedited=1 swiotlb=0  printk.time=1
[    0.000000] BIOS-provided physical RAM map:
[    0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009fbff] usable
[    0.000000] BIOS-e820: [mem 0x000000000009fc00-0x000000000009ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000000f0000-0x00000000000fffff] reserved
[    0.000000] BIOS-e820: [mem 0x0000000000100000-0x000000003ffd7fff] usable
[    0.000000] BIOS-e820: [mem 0x000000003ffd8000-0x000000003fffffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000b0000000-0x00000000bfffffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fed1c000-0x00000000fed1ffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000feffc000-0x00000000feffffff] reserved
[    0.000000] BIOS-e820: [mem 0x00000000fffc0000-0x00000000ffffffff] reserved
[    0.000000] BIOS-e820: [mem 0x000000fd00000000-0x000000ffffffffff] reserved
[    0.000000] NX (Execute Disable) protection: active
[    0.000000] APIC: Static calls initialized
[    0.000000] SMBIOS 2.8 present.
[    0.000000] DMI: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.17.0-0-gb52ca86e094d-prebuilt.qemu.org 04/01/2014
[    0.000000] DMI: Memory slots populated: 1/1
[    0.000000] Hypervisor detected: KVM
[    0.000000] last_pfn = 0x3ffd8 max_arch_pfn = 0x400000000
[    0.000000] kvm-clock: Using msrs 4b564d01 and 4b564d00
[    0.000000] kvm-clock: using sched offset of 644912964 cycles
[    0.000001] clocksource: kvm-clock: mask: 0xffffffffffffffff max_cycles: 0x1cd42e4dffb, max_idle_ns: 881590591483 ns
[    0.000003] tsc: Detected 2749.998 MHz processor
[    0.000820] last_pfn = 0x3ffd8 max_arch_pfn = 0x400000000
[    0.000853] MTRR map: 4 entries (3 fixed + 1 variable; max 19), built from 8 variable MTRRs
[    0.000855] x86/PAT: Configuration [0-7]: WB  WC  UC- UC  WB  WP  UC- WT  
[    0.002781] found SMP MP-table at [mem 0x000f5490-0x000f549f]
[    0.002841] ACPI: Early table checksum verification disabled
[    0.002843] ACPI: RSDP 0x00000000000F52B0 000014 (v00 BOCHS )
[    0.002849] ACPI: RSDT 0x000000003FFE249C 000038 (v01 BOCHS  BXPC     00000001 BXPC 00000001)
[    0.002853] ACPI: FACP 0x000000003FFE227C 0000F4 (v03 BOCHS  BXPC     00000001 BXPC 00000001)
[    0.002856] ACPI: DSDT 0x000000003FFE0040 00223C (v01 BOCHS  BXPC     00000001 BXPC 00000001)
[    0.002858] ACPI: FACS 0x000000003FFE0000 000040
[    0.002859] ACPI: APIC 0x000000003FFE2370 000090 (v03 BOCHS  BXPC     00000001 BXPC 00000001)
[    0.002861] ACPI: HPET 0x000000003FFE2400 000038 (v01 BOCHS  BXPC     00000001 BXPC 00000001)
[    0.002862] ACPI: MCFG 0x000000003FFE2438 00003C (v01 BOCHS  BXPC     00000001 BXPC 00000001)
[    0.002864] ACPI: WAET 0x000000003FFE2474 000028 (v01 BOCHS  BXPC     00000001 BXPC 00000001)
[    0.002865] ACPI: Reserving FACP table memory at [mem 0x3ffe227c-0x3ffe236f]
[    0.002866] ACPI: Reserving DSDT table memory at [mem 0x3ffe0040-0x3ffe227b]
[    0.002867] ACPI: Reserving FACS table memory at [mem 0x3ffe0000-0x3ffe003f]
[    0.002867] ACPI: Reserving APIC table memory at [mem 0x3ffe2370-0x3ffe23ff]
[    0.002868] ACPI: Reserving HPET table memory at [mem 0x3ffe2400-0x3ffe2437]
[    0.002868] ACPI: Reserving MCFG table memory at [mem 0x3ffe2438-0x3ffe2473]
[    0.002869] ACPI: Reserving WAET table memory at [mem 0x3ffe2474-0x3ffe249b]
[    0.002905] Zone ranges:
[    0.002906]   DMA      [mem 0x0000000000001000-0x0000000000ffffff]
[    0.002908]   DMA32    [mem 0x0000000001000000-0x000000003ffd7fff]
[    0.002909]   Normal   empty
[    0.002909] Movable zone start for each node
[    0.002910] Early memory node ranges
[    0.002910]   node   0: [mem 0x0000000000001000-0x000000000009efff]
[    0.002911]   node   0: [mem 0x0000000000100000-0x000000003ffd7fff]
[    0.002912] Initmem setup node 0 [mem 0x0000000000001000-0x000000003ffd7fff]
[    0.002915] On node 0, zone DMA: 1 pages in unavailable ranges
[    0.002934] On node 0, zone DMA: 97 pages in unavailable ranges
[    0.071208] On node 0, zone DMA32: 40 pages in unavailable ranges
[    0.072003] ACPI: PM-Timer IO Port: 0x608
[    0.072016] ACPI: LAPIC_NMI (acpi_id[0xff] dfl dfl lint[0x1])
[    0.072044] IOAPIC[0]: apic_id 0, version 17, address 0xfec00000, GSI 0-23
[    0.072046] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.072048] ACPI: INT_SRC_OVR (bus 0 bus_irq 5 global_irq 5 high level)
[    0.072049] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.072050] ACPI: INT_SRC_OVR (bus 0 bus_irq 10 global_irq 10 high level)
[    0.072050] ACPI: INT_SRC_OVR (bus 0 bus_irq 11 global_irq 11 high level)
[    0.072053] ACPI: Using ACPI (MADT) for SMP configuration information
[    0.072054] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[    0.072058] TSC deadline timer available
[    0.072062] CPU topo: Max. logical packages:   1
[    0.072063] CPU topo: Max. logical dies:       1
[    0.072063] CPU topo: Max. dies per package:   1
[    0.072067] CPU topo: Max. threads per core:   1
[    0.072067] CPU topo: Num. cores per package:     4
[    0.072068] CPU topo: Num. threads per package:   4
[    0.072068] CPU topo: Allowing 4 present CPUs plus 0 hotplug CPUs
[    0.072082] kvm-guest: APIC: eoi() replaced with kvm_guest_apic_eoi_write()
[    0.072098] [mem 0x40000000-0xafffffff] available for PCI devices
[    0.072099] Booting paravirtualized kernel on KVM
[    0.072101] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1910969940391419 ns
[    0.072106] setup_percpu: NR_CPUS:64 nr_cpumask_bits:4 nr_cpu_ids:4 nr_node_ids:1
[    0.078769] percpu: Embedded 54 pages/cpu s181144 r8192 d31848 u524288
[    0.078796] Kernel command line: root=/dev/vda rw  ip=192.168.7.28::192.168.7.27:255.255.255.0::eth0:off:8.8.8.8 net.ifnames=0 console=ttyS0 console=ttyS1 oprofile.timer=1 tsc=reliable no_timer_check rcupdate.rcu_expedited=1 swiotlb=0  printk.time=1
[    0.078860] random: crng init done
[    0.078861] printk: log buffer data + meta data: 131072 + 458752 = 589824 bytes
[    0.078890] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[    0.078907] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes, linear)
[    0.078939] Built 1 zonelists, mobility grouping on.  Total pages: 262006
[    0.082358] mem auto-init: stack:all(zero), heap alloc:off, heap free:off
[    0.087455] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.099280] ftrace: allocating 55907 entries in 220 pages
[    0.099282] ftrace: allocated 220 pages with 5 groups
[    0.099525] Dynamic Preempt: full
[    0.103264] rcu: Preemptible hierarchical RCU implementation.
[    0.103265] rcu: 	RCU event tracing is enabled.
[    0.103266] rcu: 	RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4.
[    0.103268] 	All grace periods are expedited (rcu_expedited).
[    0.103268] 	Trampoline variant of Tasks RCU enabled.
[    0.103268] 	Rude variant of Tasks RCU enabled.
[    0.103269] 	Tracing variant of Tasks RCU enabled.
[    0.103269] rcu: RCU calculated value of scheduler-enlistment delay is 100 jiffies.
[    0.103270] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[    0.103294] RCU Tasks: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=4.
[    0.103296] RCU Tasks Rude: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=4.
[    0.103297] RCU Tasks Trace: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=4.
[    0.109167] NR_IRQS: 4352, nr_irqs: 456, preallocated irqs: 16
[    0.109348] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[    0.109354] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns
[    0.109407] kfence: initialized - using 2097152 bytes for 255 objects at 0x(____ptrval____)-0x(____ptrval____)
[    0.118992] Console: colour VGA+ 80x25
[    0.119050] printk: legacy console [ttyS0] enabled
[    0.349947] ACPI: Core revision 20250807
[    0.351378] clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604467 ns
[    0.354434] APIC: Switch to symmetric I/O mode setup
[    0.356250] x2apic enabled
[    0.357417] APIC: Switched APIC routing to: physical x2apic
[    0.360302] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.362289] clocksource: tsc-early: mask: 0xffffffffffffffff max_cycles: 0x27a3bdae5c8, max_idle_ns: 440795216753 ns
[    0.365715] Calibrating delay loop (skipped) preset value.. 5499.99 BogoMIPS (lpj=2749998)
[    0.367829] Last level iTLB entries: 4KB 0, 2MB 0, 4MB 0
[    0.368716] Last level dTLB entries: 4KB 0, 2MB 0, 4MB 0, 1GB 0
[    0.369719] mitigations: Enabled attack vectors: user_kernel, user_user, SMT mitigations: auto
[    0.370717] Speculative Store Bypass: Vulnerable
[    0.371716] Spectre V2 : Mitigation: Retpolines
[    0.372717] Spectre V1 : Mitigation: usercopy/swapgs barriers and __user pointer sanitization
[    0.373716] Spectre V2 : Spectre v2 / SpectreRSB: Filling RSB on context switch and VMEXIT
[    0.374731] x86/fpu: Supporting XSAVE feature 0x001: 'x87 floating point registers'
[    0.375716] x86/fpu: Supporting XSAVE feature 0x002: 'SSE registers'
[    0.376716] x86/fpu: Supporting XSAVE feature 0x004: 'AVX registers'
[    0.377717] x86/fpu: xstate_offset[2]:  576, xstate_sizes[2]:  256
[    0.378716] x86/fpu: Enabled xstate features 0x7, context size is 832 bytes, using 'compacted' format.
[    0.399536] Freeing SMP alternatives memory: 64K
[    0.399719] pid_max: default: 32768 minimum: 301
[    0.400737] LSM: initializing lsm=capability,landlock
[    0.401741] landlock: Up and running.
[    0.402745] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[    0.403717] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[    0.405007] smpboot: CPU0: AMD Intel Core Processor (Skylake) (family: 0x6, model: 0x5e, stepping: 0x3)
[    0.405821] Performance Events: PMU not available due to virtualization, using software events only.
[    0.406746] signal: max sigframe size: 1776
[    0.407740] rcu: Hierarchical SRCU implementation.
[    0.408719] rcu: 	Max phase no-delay instances is 400.
[    0.409751] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level
[    0.410842] smp: Bringing up secondary CPUs ...
[    0.411785] smpboot: x86: Booting SMP configuration:
[    0.412723] .... node  #0, CPUs:      #1 #2 #3
[    0.447752] smp: Brought up 1 node, 4 CPUs
[    0.449721] smpboot: Total of 4 processors activated (21999.98 BogoMIPS)
[    0.450998] Memory: 981256K/1048024K available (21010K kernel code, 2464K rwdata, 6220K rodata, 3676K init, 1844K bss, 60744K reserved, 0K cma-reserved)
[    0.451783] devtmpfs: initialized
[    0.452869] posixtimers hash table entries: 2048 (order: 3, 32768 bytes, linear)
[    0.453725] futex hash table entries: 1024 (65536 bytes on 1 NUMA nodes, total 64 KiB, linear).
[    0.454757] pinctrl core: initialized pinctrl subsystem
[    0.456880] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.457829] thermal_sys: Registered thermal governor 'step_wise'
[    0.457841] cpuidle: using governor menu
[    0.459932] PCI: ECAM [mem 0xb0000000-0xbfffffff] (base 0xb0000000) for domain 0000 [bus 00-ff]
[    0.460721] PCI: ECAM [mem 0xb0000000-0xbfffffff] reserved as E820 entry
[    0.461726] PCI: Using configuration type 1 for base access
[    0.462767] kprobes: kprobe jump-optimization is enabled. All kprobes are optimized if possible.
[    0.482716] raid6: avx2x4   gen() 43567 MB/s
[    0.500716] raid6: avx2x2   gen() 49382 MB/s
[    0.518716] raid6: avx2x1   gen() 40006 MB/s
[    0.519718] raid6: using algorithm avx2x2 gen() 49382 MB/s
[    0.537716] raid6: .... xor() 37646 MB/s, rmw enabled
[    0.538719] raid6: using avx2x2 recovery algorithm
[    0.539791] ACPI: Added _OSI(Module Device)
[    0.540719] ACPI: Added _OSI(Processor Device)
[    0.541718] ACPI: Added _OSI(Processor Aggregator Device)
[    0.543461] ACPI: 1 ACPI AML tables successfully acquired and loaded
[    0.544036] ACPI: Interpreter enabled
[    0.544728] ACPI: PM: (supports S0 S3 S5)
[    0.545718] ACPI: Using IOAPIC for interrupt routing
[    0.546739] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.547718] PCI: Using E820 reservations for host bridge windows
[    0.548789] ACPI: Enabled 2 GPEs in block 00 to 3F
[    0.551677] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[    0.551723] acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI HPX-Type3]
[    0.552756] acpi PNP0A08:00: _OSC: platform does not support [LTR]
[    0.553768] acpi PNP0A08:00: _OSC: OS now controls [PME PCIeCapability]
[    0.554763] PCI host bridge to bus 0000:00
[    0.555721] pci_bus 0000:00: root bus resource [io  0x0000-0x0cf7 window]
[    0.556719] pci_bus 0000:00: root bus resource [io  0x0d00-0xffff window]
[    0.557718] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window]
[    0.558719] pci_bus 0000:00: root bus resource [mem 0x40000000-0xafffffff window]
[    0.559719] pci_bus 0000:00: root bus resource [mem 0xc0000000-0xfebfffff window]
[    0.560718] pci_bus 0000:00: root bus resource [mem 0x100000000-0x8ffffffff window]
[    0.561719] pci_bus 0000:00: root bus resource [bus 00-ff]
[    0.562794] pci 0000:00:00.0: [8086:29c0] type 00 class 0x060000 conventional PCI endpoint
[    0.564503] pci 0000:00:01.0: [1234:1111] type 00 class 0x030000 conventional PCI endpoint
[    0.566569] pci 0000:00:01.0: BAR 0 [mem 0xfd000000-0xfdffffff pref]
[    0.566745] pci 0000:00:01.0: BAR 2 [mem 0xfebd0000-0xfebd0fff]
[    0.567769] pci 0000:00:01.0: ROM [mem 0xfebc0000-0xfebcffff pref]
[    0.568835] pci 0000:00:01.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff]
[    0.570201] pci 0000:00:02.0: [1af4:1000] type 00 class 0x020000 conventional PCI endpoint
[    0.572461] pci 0000:00:02.0: BAR 0 [io  0xc0c0-0xc0df]
[    0.572732] pci 0000:00:02.0: BAR 1 [mem 0xfebd1000-0xfebd1fff]
[    0.573769] pci 0000:00:02.0: BAR 4 [mem 0xfe000000-0xfe003fff 64bit pref]
[    0.574732] pci 0000:00:02.0: ROM [mem 0xfeb80000-0xfebbffff pref]
[    0.576805] pci 0000:00:03.0: [1af4:1005] type 00 class 0x00ff00 conventional PCI endpoint
[    0.578732] pci 0000:00:03.0: BAR 0 [io  0xc0e0-0xc0ff]
[    0.579733] pci 0000:00:03.0: BAR 1 [mem 0xfebd2000-0xfebd2fff]
[    0.580776] pci 0000:00:03.0: BAR 4 [mem 0xfe004000-0xfe007fff 64bit pref]
[    0.582800] pci 0000:00:04.0: [1af4:1001] type 00 class 0x010000 conventional PCI endpoint
[    0.584731] pci 0000:00:04.0: BAR 0 [io  0xc000-0xc07f]
[    0.585732] pci 0000:00:04.0: BAR 1 [mem 0xfebd3000-0xfebd3fff]
[    0.586769] pci 0000:00:04.0: BAR 4 [mem 0xfe008000-0xfe00bfff 64bit pref]
[    0.588933] pci 0000:00:1d.0: [8086:2934] type 00 class 0x0c0300 conventional PCI endpoint
[    0.590440] pci 0000:00:1d.0: BAR 4 [io  0xc100-0xc11f]
[    0.590992] pci 0000:00:1d.1: [8086:2935] type 00 class 0x0c0300 conventional PCI endpoint
[    0.592445] pci 0000:00:1d.1: BAR 4 [io  0xc120-0xc13f]
[    0.592994] pci 0000:00:1d.2: [8086:2936] type 00 class 0x0c0300 conventional PCI endpoint
[    0.594507] pci 0000:00:1d.2: BAR 4 [io  0xc140-0xc15f]
[    0.595032] pci 0000:00:1d.7: [8086:293a] type 00 class 0x0c0320 conventional PCI endpoint
[    0.596409] pci 0000:00:1d.7: BAR 0 [mem 0xfebd4000-0xfebd4fff]
[    0.597059] pci 0000:00:1f.0: [8086:2918] type 00 class 0x060100 conventional PCI endpoint
[    0.598358] pci 0000:00:1f.0: quirk: [io  0x0600-0x067f] claimed by ICH6 ACPI/GPIO/TCO
[    0.599095] pci 0000:00:1f.2: [8086:2922] type 00 class 0x010601 conventional PCI endpoint
[    0.600620] pci 0000:00:1f.2: BAR 4 [io  0xc160-0xc17f]
[    0.600733] pci 0000:00:1f.2: BAR 5 [mem 0xfebd5000-0xfebd5fff]
[    0.602322] pci 0000:00:1f.3: [8086:2930] type 00 class 0x0c0500 conventional PCI endpoint
[    0.603426] pci 0000:00:1f.3: BAR 4 [io  0x0700-0x073f]
[    0.607181] ACPI: PCI: Interrupt link LNKA configured for IRQ 10
[    0.607826] ACPI: PCI: Interrupt link LNKB configured for IRQ 10
[    0.608825] ACPI: PCI: Interrupt link LNKC configured for IRQ 11
[    0.609823] ACPI: PCI: Interrupt link LNKD configured for IRQ 11
[    0.610824] ACPI: PCI: Interrupt link LNKE configured for IRQ 10
[    0.611823] ACPI: PCI: Interrupt link LNKF configured for IRQ 10
[    0.612823] ACPI: PCI: Interrupt link LNKG configured for IRQ 11
[    0.613823] ACPI: PCI: Interrupt link LNKH configured for IRQ 11
[    0.614765] ACPI: PCI: Interrupt link GSIA configured for IRQ 16
[    0.615729] ACPI: PCI: Interrupt link GSIB configured for IRQ 17
[    0.616731] ACPI: PCI: Interrupt link GSIC configured for IRQ 18
[    0.617745] ACPI: PCI: Interrupt link GSID configured for IRQ 19
[    0.618728] ACPI: PCI: Interrupt link GSIE configured for IRQ 20
[    0.619753] ACPI: PCI: Interrupt link GSIF configured for IRQ 21
[    0.620730] ACPI: PCI: Interrupt link GSIG configured for IRQ 22
[    0.621729] ACPI: PCI: Interrupt link GSIH configured for IRQ 23
[    0.623153] iommu: Default domain type: Translated
[    0.623718] iommu: DMA domain TLB invalidation policy: lazy mode
[    0.624812] SCSI subsystem initialized
[    0.625771] ACPI: bus type USB registered
[    0.626732] usbcore: registered new interface driver usbfs
[    0.627725] usbcore: registered new interface driver hub
[    0.628727] usbcore: registered new device driver usb
[    0.629732] pps_core: LinuxPPS API ver. 1 registered
[    0.630718] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.631724] PTP clock support registered
[    0.632872] Bluetooth: Core ver 2.22
[    0.633727] NET: Registered PF_BLUETOOTH protocol family
[    0.634718] Bluetooth: HCI device and connection manager initialized
[    0.635719] Bluetooth: HCI socket layer initialized
[    0.636719] Bluetooth: L2CAP socket layer initialized
[    0.637721] Bluetooth: SCO socket layer initialized
[    0.638789] PCI: Using ACPI for IRQ routing
[    0.740881] pci 0000:00:01.0: vgaarb: setting as boot VGA device
[    0.741714] pci 0000:00:01.0: vgaarb: bridge control possible
[    0.741714] pci 0000:00:01.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none
[    0.741722] vgaarb: loaded
[    0.742717] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[    0.743718] hpet0: 3 comparators, 64-bit 100.000000 MHz counter
[    0.748784] clocksource: Switched to clocksource kvm-clock
[    0.754230] pnp: PnP ACPI init
[    0.755372] ACPI: IRQ 3 override to edge(!), high(!)
[    0.757062] ACPI: IRQ 4 override to edge(!), high(!)
[    0.758773] system 00:04: [mem 0xb0000000-0xbfffffff window] has been reserved
[    0.761466] pnp: PnP ACPI: found 5 devices
[    0.768962] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
[    0.771898] NET: Registered PF_INET protocol family
[    0.773575] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear)
[    0.776281] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes, linear)
[    0.779047] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.781571] TCP established hash table entries: 8192 (order: 4, 65536 bytes, linear)
[    0.784119] TCP bind hash table entries: 8192 (order: 6, 262144 bytes, linear)
[    0.787356] TCP: Hash tables configured (established 8192 bind 8192)
[    0.789527] UDP hash table entries: 512 (order: 3, 32768 bytes, linear)
[    0.791715] UDP-Lite hash table entries: 512 (order: 3, 32768 bytes, linear)
[    0.794138] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    0.796342] RPC: Registered named UNIX socket transport module.
[    0.798359] RPC: Registered udp transport module.
[    0.799943] RPC: Registered tcp transport module.
[    0.801532] RPC: Registered tcp-with-tls transport module.
[    0.803375] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.805507] pci_bus 0000:00: resource 4 [io  0x0000-0x0cf7 window]
[    0.807596] pci_bus 0000:00: resource 5 [io  0x0d00-0xffff window]
[    0.809715] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window]
[    0.812033] pci_bus 0000:00: resource 7 [mem 0x40000000-0xafffffff window]
[    0.814451] pci_bus 0000:00: resource 8 [mem 0xc0000000-0xfebfffff window]
[    0.816804] pci_bus 0000:00: resource 9 [mem 0x100000000-0x8ffffffff window]
[    0.819434] ACPI: \_SB_.GSIA: Enabled at IRQ 16
[    0.821627] ACPI: \_SB_.GSIB: Enabled at IRQ 17
[    0.823828] ACPI: \_SB_.GSIC: Enabled at IRQ 18
[    0.825998] ACPI: \_SB_.GSID: Enabled at IRQ 19
[    0.828231] PCI: CLS 0 bytes, default 64
[    0.829707] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x27a3bdae5c8, max_idle_ns: 440795216753 ns
[    0.834074] Initialise system trusted keyrings
[    0.835795] workingset: timestamp_bits=46 max_order=18 bucket_order=0
[    0.838171] NFS: Registering the id_resolver key type
[    0.839892] Key type id_resolver registered
[    0.841328] Key type id_legacy registered
[    0.843109] Key type cifs.idmap registered
[    0.851387] xor: automatically using best checksumming function   avx       
[    0.853828] Key type asymmetric registered
[    0.855242] Asymmetric key parser 'x509' registered
[    0.856923] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
[    0.859409] io scheduler mq-deadline registered
[    0.860983] io scheduler kyber registered
[    0.862351] io scheduler bfq registered
[    0.863968] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
[    0.870384] ACPI: button: Power Button [PWRF]
[    0.872597] ACPI: \_SB_.GSIG: Enabled at IRQ 22
[    0.875912] ACPI: \_SB_.GSIH: Enabled at IRQ 23
[    0.878917] ACPI: \_SB_.GSIE: Enabled at IRQ 20
[    0.882048] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    0.884411] 00:01: ttyS1 at I/O 0x2f8 (irq = 3, base_baud = 115200) is a 16550A
[    0.887180] 00:02: ttyS0 at I/O 0x3f8 (irq = 4, base_baud = 115200) is a 16550A
[    0.891191] Linux agpgart interface v0.103
[    0.892706] ACPI: bus type drm_connector registered
[    0.894370] bochs-drm 0000:00:01.0: vgaarb: deactivate vga console
[    0.900763] Console: switching to colour dummy device 80x25
[    0.902762] [drm] Found bochs VGA, ID 0xb0c5.
[    0.904256] [drm] Framebuffer size 16384 kB @ 0xfd000000, mmio @ 0xfebd0000.
[    0.907021] [drm] Initialized bochs-drm 1.0.0 for 0000:00:01.0 on minor 0
[    0.922050] Console: switching to colour frame buffer device 160x50
[    0.924812] bochs-drm 0000:00:01.0: [drm] fb0: bochs-drmdrmfb frame buffer device
[    0.933388] brd: module loaded
[    0.936375] loop: module loaded
[    0.937686] virtio_blk virtio2: 4/0/0 default/read/poll queues
[    0.941800] virtio_blk virtio2: [vda] 3274728 512-byte logical blocks (1.68 GB/1.56 GiB)
[    0.946982] ahci 0000:00:1f.2: AHCI vers 0001.0000, 32 command slots, 1.5 Gbps, SATA mode
[    0.949812] ahci 0000:00:1f.2: 6/6 ports implemented (port mask 0x3f)
[    0.952016] ahci 0000:00:1f.2: flags: 64bit ncq only 
[    0.955575] scsi host0: ahci
[    0.956810] scsi host1: ahci
[    0.958051] scsi host2: ahci
[    0.959241] scsi host3: ahci
[    0.961688] scsi host4: ahci
[    0.962823] scsi host5: ahci
[    0.963893] ata1: SATA max UDMA/133 abar m4096@0xfebd5000 port 0xfebd5100 irq 31 lpm-pol 1
[    0.966653] ata2: SATA max UDMA/133 abar m4096@0xfebd5000 port 0xfebd5180 irq 31 lpm-pol 1
[    0.969449] ata3: SATA max UDMA/133 abar m4096@0xfebd5000 port 0xfebd5200 irq 31 lpm-pol 1
[    0.972297] ata4: SATA max UDMA/133 abar m4096@0xfebd5000 port 0xfebd5280 irq 31 lpm-pol 1
[    0.975094] ata5: SATA max UDMA/133 abar m4096@0xfebd5000 port 0xfebd5300 irq 31 lpm-pol 1
[    0.977902] ata6: SATA max UDMA/133 abar m4096@0xfebd5000 port 0xfebd5380 irq 31 lpm-pol 1
[    0.982642] e100: Intel(R) PRO/100 Network Driver
[    0.984446] e100: Copyright(c) 1999-2006 Intel Corporation
[    0.986371] e1000: Intel(R) PRO/1000 Network Driver
[    0.988033] e1000: Copyright (c) 1999-2006 Intel Corporation.
[    0.989975] e1000e: Intel(R) PRO/1000 Network Driver
[    0.991685] e1000e: Copyright(c) 1999 - 2015 Intel Corporation.
[    0.993694] igb: Intel(R) Gigabit Ethernet Network Driver
[    0.995513] igb: Copyright (c) 2007-2014 Intel Corporation.
[    0.998229] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[    1.000373] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[    1.003038] uhci_hcd 0000:00:1d.0: irq 16, io port 0x0000c100
[    1.005453] hub 1-0:1.0: USB hub found
[    1.006779] hub 1-0:1.0: 2 ports detected
[    1.008425] ehci-pci 0000:00:1d.7: EHCI Host Controller
[    1.011975] ehci-pci 0000:00:1d.7: new USB bus registered, assigned bus number 2
[    1.017289] ehci-pci 0000:00:1d.7: irq 19, io mem 0xfebd4000
[    1.026428] ehci-pci 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[    1.030460] hub 2-0:1.0: USB hub found
[    1.032922] hub 2-0:1.0: 6 ports detected
[    1.056571] hub 1-0:1.0: USB hub found
[    1.059729] hub 1-0:1.0: 2 ports detected
[    1.063273] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[    1.067723] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[    1.074136] uhci_hcd 0000:00:1d.1: irq 17, io port 0x0000c120
[    1.079182] hub 3-0:1.0: USB hub found
[    1.082287] hub 3-0:1.0: 2 ports detected
[    1.087080] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[    1.091334] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[    1.097983] uhci_hcd 0000:00:1d.2: irq 18, io port 0x0000c140
[    1.102921] hub 4-0:1.0: USB hub found
[    1.106010] hub 4-0:1.0: 2 ports detected
[    1.109713] usbcore: registered new interface driver usb-storage
[    1.114913] usbcore: registered new interface driver usbserial_generic
[    1.119932] usbserial: USB Serial support registered for generic
[    1.123940] usbcore: registered new interface driver ftdi_sio
[    1.127615] usbserial: USB Serial support registered for FTDI USB Serial Device
[    1.132277] usbcore: registered new interface driver pl2303
[    1.135835] usbserial: USB Serial support registered for pl2303
[    1.139638] i8042: PNP: No PS/2 controller found.
[    1.141536] mousedev: PS/2 mouse device common for all mice
[    1.143452] rtc_cmos 00:03: RTC can wake from S4
[    1.145643] rtc_cmos 00:03: registered as rtc0
[    1.147186] rtc_cmos 00:03: setting system clock to 2026-09-05T11:56:26 UTC (1788609386)
[    1.149912] rtc_cmos 00:03: alarms up to one day, y3k, 242 bytes nvram, hpet irqs
[    1.152573] device-mapper: ioctl: 4.50.0-ioctl (2025-04-28) initialised: dm-devel@lists.linux.dev
[    1.153290] i801_smbus 0000:00:1f.3: SMBus using PCI interrupt
[    1.155566] amd_pstate: the _CPC object is not present in SBIOS or ACPI disabled
[    1.160623] i2c i2c-0: Memory type 0x07 not supported yet, not instantiating SPD
[    1.162796] sdhci: Secure Digital Host Controller Interface driver
[    1.170590] sdhci: Copyright(c) Pierre Ossman
[    1.172039] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.173987] usbcore: registered new interface driver usbhid
[    1.175801] usbhid: USB HID core driver
[    1.177094] u32 classifier
[    1.177988]     input device check on
[    1.179170]     Actions configured
[    1.180338] NET: Registered PF_INET6 protocol family
[    1.182286] Segment Routing with IPv6
[    1.183489] In-situ OAM (IOAM) with IPv6
[    1.184799] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[    1.186820] NET: Registered PF_PACKET protocol family
[    1.188453] Bridge firewalling registered
[    1.189783] l2tp_core: L2TP core driver, V2.0
[    1.191220] Key type dns_resolver registered
[    1.192732] NET: Registered PF_VSOCK protocol family
[    1.194747] IPI shorthand broadcast: enabled
[    1.197137] sched_clock: Marking stable (945002192, 251360393)->(1373184469, -176821884)
[    1.199895] registered taskstats version 1
[    1.201283] Loading compiled-in X.509 certificates
[    1.203700] Key type .fscrypt registered
[    1.205031] Key type fscrypt-provisioning registered
[    1.206793] Btrfs loaded, zoned=no, fsverity=no
[    1.208945] Key type encrypted registered
[    1.210313] netconsole: network logging started
[    1.274445] usb 2-1: new high-speed USB device number 2 using ehci-pci
[    1.287187] ata5: SATA link down (SStatus 0 SControl 300)
[    1.289519] ata2: SATA link down (SStatus 0 SControl 300)
[    1.294498] ata1: SATA link down (SStatus 0 SControl 300)
[    1.299541] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    1.304745] ata4: SATA link down (SStatus 0 SControl 300)
[    1.306576] ata3.00: ATAPI: QEMU DVD-ROM, 2.5+, max UDMA/100
[    1.311060] ata3.00: applying bridge limits
[    1.314955] ata6: SATA link down (SStatus 0 SControl 300)
[    1.319675] ata3.00: configured for UDMA/100
[    1.324074] scsi 2:0:0:0: CD-ROM            QEMU     QEMU DVD-ROM     2.5+ PQ: 0 ANSI: 5
[    1.345941] sr 2:0:0:0: [sr0] scsi3-mmc drive: 4x/4x cd/rw xa/form2 tray
[    1.363813] cdrom: Uniform CD-ROM driver Revision: 3.20
[    1.385392] IP-Config: Complete:
[    1.388007]      device=eth0, hwaddr=52:54:00:12:34:1c, ipaddr=192.168.7.28, mask=255.255.255.0, gw=192.168.7.27
[    1.396050]      host=192.168.7.28, domain=, nis-domain=(none)
[    1.400830]      bootserver=255.255.255.255, rootserver=255.255.255.255, rootpath=
[    1.400834]      nameserver0=8.8.8.8
[    1.410040] clk: Disabling unused clocks
[    1.414152] md: Waiting for all devices to be available before autodetect
[    1.418429] md: If you don't use raid, use raid=noautodetect
[    1.421381] md: Autodetecting RAID arrays.
[    1.423491] md: autorun ...
[    1.424954] md: ... autorun DONE.
[    1.430461] input: QEMU QEMU USB Tablet as /devices/pci0000:00/0000:00:1d.7/usb2/2-1/2-1:1.0/0003:0627:0001.0001/input/input1
[    1.435661] EXT4-fs (vda): mounted filesystem f67b0a1f-b786-49a5-8653-72596c3a8318 r/w with ordered data mode. Quota mode: disabled.
[    1.436620] hid-generic 0003:0627:0001.0001: input: USB HID v0.01 Mouse [QEMU QEMU USB Tablet] on usb-0000:00:1d.7-1/input0
[    1.442375] VFS: Mounted root (ext4 filesystem) on device 253:0.
[    1.451671] devtmpfs: mounted
[    1.454310] Freeing unused kernel image (initmem) memory: 3676K
[    1.457374] Write protecting the kernel read-only data: 30720k
[    1.460775] Freeing unused kernel image (text/rodata gap) memory: 1516K
[    1.465243] Freeing unused kernel image (rodata/data gap) memory: 1972K
[    1.468648] Run /sbin/init as init process
INIT: version 3.14 booting
Starting udev
[    1.556966] udevd[141]: starting version 3.2.14
[    1.561422] usb 2-2: new high-speed USB device number 3 using ehci-pci
[    1.569550] udevd[142]: starting eudev-3.2.14
[    1.697573] input: QEMU QEMU USB Keyboard as /devices/pci0000:00/0000:00:1d.7/usb2/2-2/2-2:1.0/0003:0627:0001.0002/input/input2
[    1.754869] hid-generic 0003:0627:0001.0002: input: USB HID v1.11 Keyboard [QEMU QEMU USB Keyboard] on usb-0000:00:1d.7-2/input0
[    1.821189] EXT4-fs (vda): re-mounted f67b0a1f-b786-49a5-8653-72596c3a8318.
INIT: Entering runlevel: 5
Configuring network interfaces... Error: ipv4: Address already assigned.
Starting OpenBSD Secure Shell server: sshd
  generating ssh ECDSA host key...
done.
Starting syslogd/klogd: done

Poky (Yocto Project Reference Distro) 6.0.99+snapshot-b32446f5eaab92090374d599d72f00d9261f8792 qemux86-64 ttyS0

Type 'root' to login with superuser privileges (no password will be asked).

qemux86-64 login: [   10.523192] loop0: detected capacity change from 0 to 20480
[   10.610255] loop0: detected capacity change from 0 to 10240
[   10.624162] loop1: detected capacity change from 0 to 10240
[   16.049708] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1)
[   16.052114] scsi host6: scsi_debug: version 0191 [20210520]
[   16.052114]   dev_size_mb=50, opts=0x0, submit_queues=1, statistics=0
[   16.074762] scsi 6:0:0:0: Direct-Access     Linux    scsi_debug       0191 PQ: 0 ANSI: 7
[   16.077018] scsi 6:0:0:0: Power-on or device reset occurred
[   16.083667] sd 6:0:0:0: [sda] 102400 512-byte logical blocks: (52.4 MB/50.0 MiB)
[   16.089641] sd 6:0:0:0: [sda] Write Protect is off
[   16.094954] sd 6:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
[   16.106677] sd 6:0:0:0: [sda] permanent stream count = 5
[   16.113304] sd 6:0:0:0: [sda] Preferred minimum I/O size 512 bytes
[   16.117326] sd 6:0:0:0: [sda] Optimal transfer size 524288 bytes
[   16.143473] sd 6:0:0:0: [sda] Attached SCSI disk
[   16.859999]  sda: sda1 sda2 sda3 sda4
[   17.030527] sd 6:0:0:0: [sda] Synchronizing SCSI cache
[   17.089737] loop0: detected capacity change from 0 to 10240
[   17.430032] loop0: detected capacity change from 0 to 10240
[   17.690510]  loop0: p1
[   20.472313] loop0: detected capacity change from 0 to 8
[   22.240173] loop0: detected capacity change from 0 to 120
[   23.253864] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1)
[   23.256272] scsi host6: scsi_debug: version 0191 [20210520]
[   23.256272]   dev_size_mb=100, opts=0x0, submit_queues=1, statistics=0
[   23.263336] scsi 6:0:0:0: Direct-Access     Linux    scsi_debug       0191 PQ: 0 ANSI: 7
[   23.265450] scsi 6:0:0:0: Power-on or device reset occurred
[   23.272093] sd 6:0:0:0: [sda] 204800 512-byte logical blocks: (105 MB/100 MiB)
[   23.275321] sd 6:0:0:0: [sda] Write Protect is off
[   23.278805] sd 6:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
[   23.287389] sd 6:0:0:0: [sda] permanent stream count = 5
[   23.291997] sd 6:0:0:0: [sda] Preferred minimum I/O size 512 bytes
[   23.293848] sd 6:0:0:0: [sda] Optimal transfer size 524288 bytes
[   23.316452] sd 6:0:0:0: [sda] Attached SCSI disk
[   24.332258] sd 6:0:0:0: [sda] Spinning up disk...
[   25.352436] .ready
[   25.389594] sd 6:0:0:0: [sda] Synchronizing SCSI cache
[   25.444571] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1)
[   25.450517] scsi host6: scsi_debug: version 0191 [20210520]
[   25.450517]   dev_size_mb=100, opts=0x0, submit_queues=1, statistics=0
[   25.458441] scsi 6:0:0:0: Direct-Access     Linux    scsi_debug       0191 PQ: 0 ANSI: 7
[   25.463898] scsi 6:0:0:0: Power-on or device reset occurred
[   25.472895] sd 6:0:0:0: [sda] 204800 512-byte logical blocks: (105 MB/100 MiB)
[   25.476108] sd 6:0:0:0: [sda] Write Protect is off
[   25.479602] sd 6:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
[   25.488305] sd 6:0:0:0: [sda] permanent stream count = 5
[   25.492917] sd 6:0:0:0: [sda] Preferred minimum I/O size 512 bytes
[   25.495619] sd 6:0:0:0: [sda] Optimal transfer size 524288 bytes
[   25.518471] sd 6:0:0:0: [sda] Attached SCSI disk
[   25.765979] EXT4-fs (sda): mounting ext2 file system using the ext4 subsystem
[   25.773169] EXT4-fs (sda): mounted filesystem a07c3e27-c39d-41e1-ad4e-670b8fc18a49 r/w without journal. Quota mode: disabled.
[   25.832724] EXT4-fs (sda): unmounting filesystem a07c3e27-c39d-41e1-ad4e-670b8fc18a49.
[   26.841705] sd 6:0:0:0: [sda] Spinning up disk...
[   27.848434] .ready
[   27.888654] sd 6:0:0:0: [sda] Synchronizing SCSI cache
[   27.983647] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1)
[   27.988240] scsi host6: scsi_debug: version 0191 [20210520]
[   27.988240]   dev_size_mb=100, opts=0x0, submit_queues=1, statistics=0
[   27.994451] scsi 6:0:0:0: Direct-Access     Linux    scsi_debug       0191 PQ: 0 ANSI: 7
[   27.999528] scsi 6:0:0:0: Power-on or device reset occurred
[   28.007652] sd 6:0:0:0: [sda] 204800 512-byte logical blocks: (105 MB/100 MiB)
[   28.010787] sd 6:0:0:0: [sda] Write Protect is off
[   28.014230] sd 6:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
[   28.022752] sd 6:0:0:0: [sda] permanent stream count = 5
[   28.027335] sd 6:0:0:0: [sda] Preferred minimum I/O size 512 bytes
[   28.029146] sd 6:0:0:0: [sda] Optimal transfer size 524288 bytes
[   28.052461] sd 6:0:0:0: [sda] Attached SCSI disk
[   28.156735]  sda: sda1 sda2
[   28.592010] EXT4-fs (sda1): mounting ext2 file system using the ext4 subsystem
[   28.600348] EXT4-fs (sda1): mounted filesystem 1c238a84-ca95-4a0e-ab4a-83fe2a8ef905 r/w without journal. Quota mode: disabled.
[   28.620967] EXT4-fs (sda2): mounting ext2 file system using the ext4 subsystem
[   28.628886] EXT4-fs (sda2): mounted filesystem dacbd4cd-e59e-44e4-9dbb-9d9b745fc173 r/w without journal. Quota mode: disabled.
[   28.690834] EXT4-fs (sda2): unmounting filesystem dacbd4cd-e59e-44e4-9dbb-9d9b745fc173.
[   28.746121] EXT4-fs (sda1): unmounting filesystem 1c238a84-ca95-4a0e-ab4a-83fe2a8ef905.
[   29.758112] sd 6:0:0:0: [sda] Spinning up disk...
[   30.792524] .ready
[   30.814638]  sda: sda1 sda2
[   30.831580] sd 6:0:0:0: [sda] Synchronizing SCSI cache
[   30.925945] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1)
[   30.931885] scsi host6: scsi_debug: version 0191 [20210520]
[   30.931885]   dev_size_mb=100, opts=0x0, submit_queues=1, statistics=0
[   30.939930] scsi 6:0:0:0: Direct-Access     Linux    scsi_debug       0191 PQ: 0 ANSI: 7
[   30.945467] scsi 6:0:0:0: Power-on or device reset occurred
[   30.952519] sd 6:0:0:0: [sda] 204800 512-byte logical blocks: (105 MB/100 MiB)
[   30.955483] sd 6:0:0:0: [sda] Write Protect is off
[   30.958755] sd 6:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
[   30.966957] sd 6:0:0:0: [sda] permanent stream count = 5
[   30.971327] sd 6:0:0:0: [sda] Preferred minimum I/O size 512 bytes
[   30.972898] sd 6:0:0:0: [sda] Optimal transfer size 524288 bytes
[   30.995425] sd 6:0:0:0: [sda] Attached SCSI disk
[   31.088733]  sda: sda1 sda2
[   32.516086] sd 6:0:0:0: [sda] Spinning up disk...
[   33.544443] .ready
[   33.567666]  sda: sda1 sda2
[   33.586662] sd 6:0:0:0: [sda] Synchronizing SCSI cache
[   33.645776] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1)
[   33.651665] scsi host6: scsi_debug: version 0191 [20210520]
[   33.651665]   dev_size_mb=100, opts=0x0, submit_queues=1, statistics=0
[   33.659718] scsi 6:0:0:0: Direct-Access     Linux    scsi_debug       0191 PQ: 0 ANSI: 7
[   33.665205] scsi 6:0:0:0: Power-on or device reset occurred
[   33.674377] sd 6:0:0:0: [sda] 204800 512-byte logical blocks: (105 MB/100 MiB)
[   33.680222] sd 6:0:0:0: [sda] Write Protect is off
[   33.685521] sd 6:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
[   33.697352] sd 6:0:0:0: [sda] permanent stream count = 5
[   33.703968] sd 6:0:0:0: [sda] Preferred minimum I/O size 512 bytes
[   33.708029] sd 6:0:0:0: [sda] Optimal transfer size 524288 bytes
[   33.733476] sd 6:0:0:0: [sda] Attached SCSI disk
[   33.828637]  sda: sda1 sda2
[   34.261168] EXT4-fs (sda1): mounting ext2 file system using the ext4 subsystem
[   34.268666] EXT4-fs (sda1): mounted filesystem 1a73bc52-bd02-44bf-bc03-c344f7101f8b r/w without journal. Quota mode: disabled.
[   34.283861] EXT4-fs (sda2): mounting ext2 file system using the ext4 subsystem
[   34.289152] EXT4-fs (sda2): mounted filesystem 1ceed16c-1cbb-40e5-b2b0-0eebb13743b9 r/w without journal. Quota mode: disabled.
[   34.346685] EXT4-fs (sda2): unmounting filesystem 1ceed16c-1cbb-40e5-b2b0-0eebb13743b9.
[   34.404424] EXT4-fs (sda1): unmounting filesystem 1a73bc52-bd02-44bf-bc03-c344f7101f8b.
[   35.416982] sd 6:0:0:0: [sda] Spinning up disk...
[   36.424436] .ready
[   36.447619]  sda: sda1 sda2
[   36.464605] sd 6:0:0:0: [sda] Synchronizing SCSI cache
[   36.867285] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1)
[   36.872671] scsi host6: scsi_debug: version 0191 [20210520]
[   36.872671]   dev_size_mb=50, opts=0x0, submit_queues=1, statistics=0
[   36.879653] scsi 6:0:0:0: Direct-Access     Linux    scsi_debug       0191 PQ: 0 ANSI: 7
[   36.884498] scsi 6:0:0:0: Power-on or device reset occurred
[   36.893527] sd 6:0:0:0: [sda] 102400 512-byte logical blocks: (52.4 MB/50.0 MiB)
[   36.895764] sd 6:0:0:0: [sda] 4096-byte physical blocks
[   36.898348] sd 6:0:0:0: [sda] Write Protect is off
[   36.901854] sd 6:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
[   36.910500] sd 6:0:0:0: [sda] permanent stream count = 5
[   36.915139] sd 6:0:0:0: [sda] Preferred minimum I/O size 4096 bytes
[   36.916995] sd 6:0:0:0: [sda] Optimal transfer size 524288 bytes
[   36.940469] sd 6:0:0:0: [sda] Attached SCSI disk
[   37.151867]  sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 >
[   37.227643] sd 6:0:0:0: [sda] Synchronizing SCSI cache
[   37.293694] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1)
[   37.299920] scsi host6: scsi_debug: version 0191 [20210520]
[   37.299920]   dev_size_mb=50, opts=0x0, submit_queues=1, statistics=0
[   37.308025] scsi 6:0:0:0: Direct-Access     Linux    scsi_debug       0191 PQ: 0 ANSI: 7
[   37.313570] scsi 6:0:0:0: Power-on or device reset occurred
[   37.322630] sd 6:0:0:0: [sda] physical block alignment offset: 3584
[   37.324268] sd 6:0:0:0: [sda] 102400 512-byte logical blocks: (52.4 MB/50.0 MiB)
[   37.326136] sd 6:0:0:0: [sda] 4096-byte physical blocks
[   37.328482] sd 6:0:0:0: [sda] Write Protect is off
[   37.331799] sd 6:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
[   37.340040] sd 6:0:0:0: [sda] permanent stream count = 5
[   37.344422] sd 6:0:0:0: [sda] Preferred minimum I/O size 4096 bytes
[   37.346055] sd 6:0:0:0: [sda] Optimal transfer size 524288 bytes
[   37.368424] sd 6:0:0:0: [sda] Attached SCSI disk
[   37.589991]  sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 >
[   37.669676] sd 6:0:0:0: [sda] Synchronizing SCSI cache
[   37.738915] loop0: detected capacity change from 0 to 102400
[   37.824092] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1)
[   37.830118] scsi host6: scsi_debug: version 0191 [20210520]
[   37.830118]   dev_size_mb=50, opts=0x0, submit_queues=1, statistics=0
[   37.838171] scsi 6:0:0:0: Direct-Access     Linux    scsi_debug       0191 PQ: 0 ANSI: 7
[   37.843657] scsi 6:0:0:0: Power-on or device reset occurred
[   37.852727] sd 6:0:0:0: [sda] 102400 512-byte logical blocks: (52.4 MB/50.0 MiB)
[   37.858663] sd 6:0:0:0: [sda] Write Protect is off
[   37.863981] sd 6:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
[   37.875797] sd 6:0:0:0: [sda] permanent stream count = 5
[   37.882440] sd 6:0:0:0: [sda] Preferred minimum I/O size 512 bytes
[   37.886581] sd 6:0:0:0: [sda] Optimal transfer size 524288 bytes
[   37.911481] sd 6:0:0:0: [sda] Attached SCSI disk
[   38.123016]  sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 >
[   38.196685] sd 6:0:0:0: [sda] Synchronizing SCSI cache
[   38.563641] loop0: detected capacity change from 0 to 20480
[   38.592645] loop0: detected capacity change from 20480 to 40960
[   38.611292]  loop0: p1 p2
[   47.957145] loop0: detected capacity change from 0 to 10240
[   47.973598] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem
[   47.979484] EXT4-fs (loop0): mounted filesystem 97edf334-cebd-445b-a043-5d30a8863724 r/w without journal. Quota mode: disabled.
[   47.990639] EXT4-fs (loop0): unmounting filesystem 97edf334-cebd-445b-a043-5d30a8863724.
[   48.675331] NET: Registered PF_ALG protocol family
[   52.019916] loop0: detected capacity change from 0 to 20480
[   52.023932] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem
[   52.029262] EXT4-fs (loop0): mounted filesystem f4f1b9ca-5302-4465-96fa-6dde1b67e402 r/w without journal. Quota mode: disabled.
[   52.036293] EXT4-fs (loop0): unmounting filesystem f4f1b9ca-5302-4465-96fa-6dde1b67e402.
[   52.057986] loop0: detected capacity change from 0 to 20480
[   52.063423] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem
[   52.067933] EXT4-fs (loop0): mounted filesystem f4f1b9ca-5302-4465-96fa-6dde1b67e402 r/w without journal. Quota mode: disabled.
[   52.077100] EXT4-fs (loop0): unmounting filesystem f4f1b9ca-5302-4465-96fa-6dde1b67e402.
[   52.097377] loop0: detected capacity change from 0 to 20480
[   52.103154] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem
[   52.107555] EXT4-fs (loop0): mounted filesystem f4f1b9ca-5302-4465-96fa-6dde1b67e402 r/w without journal. Quota mode: disabled.
[   52.116779] EXT4-fs (loop0): unmounting filesystem f4f1b9ca-5302-4465-96fa-6dde1b67e402.
[   52.138503] loop0: detected capacity change from 0 to 20480
[   52.142837] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem
[   52.147146] EXT4-fs (loop0): mounted filesystem f4f1b9ca-5302-4465-96fa-6dde1b67e402 r/w without journal. Quota mode: disabled.
[   52.156109] EXT4-fs (loop0): unmounting filesystem f4f1b9ca-5302-4465-96fa-6dde1b67e402.
[   52.171907] loop0: detected capacity change from 0 to 20480
[   52.176923] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem
[   52.181150] EXT4-fs (loop0): mounted filesystem f4f1b9ca-5302-4465-96fa-6dde1b67e402 r/w without journal. Quota mode: disabled.
[   52.189894] EXT4-fs (loop0): unmounting filesystem f4f1b9ca-5302-4465-96fa-6dde1b67e402.
[   52.205103] loop0: detected capacity change from 0 to 20478
[   52.222153] loop0: detected capacity change from 0 to 20480
[   52.239755] loop0: detected capacity change from 0 to 20480
[   52.256276] loop0: detected capacity change from 0 to 20480
[   52.260163] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem
[   52.265709] EXT4-fs (loop0): mounted filesystem f4f1b9ca-5302-4465-96fa-6dde1b67e402 r/w without journal. Quota mode: disabled.
[   52.276086] EXT4-fs (loop0): unmounting filesystem f4f1b9ca-5302-4465-96fa-6dde1b67e402.
[   52.345485] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem
[   52.351351] EXT4-fs (loop0): mounted filesystem d1a4b25e-a356-4ba7-89e9-c5f8a77d51d1 r/w without journal. Quota mode: disabled.
[   52.360058] EXT4-fs (loop0): unmounting filesystem d1a4b25e-a356-4ba7-89e9-c5f8a77d51d1.
[   52.367697] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem
[   52.373177] EXT4-fs (loop0): mounted filesystem d1a4b25e-a356-4ba7-89e9-c5f8a77d51d1 r/w without journal. Quota mode: disabled.
[   52.382646] EXT4-fs (loop1): mounting ext2 file system using the ext4 subsystem
[   52.385088] EXT4-fs (loop1): mounted filesystem d1a4b25e-a356-4ba7-89e9-c5f8a77d51d1 r/w without journal. Quota mode: disabled.
[   52.389424] EXT4-fs (loop0): unmounting filesystem d1a4b25e-a356-4ba7-89e9-c5f8a77d51d1.
[   52.396922] EXT4-fs (loop1): unmounting filesystem d1a4b25e-a356-4ba7-89e9-c5f8a77d51d1.
[   57.060773] set_capacity_and_notify: 4 callbacks suppressed
[   57.060776] loop0: detected capacity change from 0 to 20480
[   57.071531] loop0: detected capacity change from 0 to 18432
[   57.080320] loop0: detected capacity change from 0 to 6144
[   57.091335] loop0: detected capacity change from 0 to 6144
[   57.131537] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1)
[   57.134402] scsi host6: scsi_debug: version 0191 [20210520]
[   57.134402]   dev_size_mb=11, opts=0x0, submit_queues=1, statistics=0
[   57.138219] scsi 6:0:0:0: Direct-Access     Linux    scsi_debug       0191 PQ: 0 ANSI: 7
[   57.140590] scsi 6:0:0:0: Power-on or device reset occurred
[   57.147232] sd 6:0:0:0: [sda] 22528 512-byte logical blocks: (11.5 MB/11.0 MiB)
[   57.150427] sd 6:0:0:0: [sda] Write Protect is off
[   57.153849] sd 6:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
[   57.162423] sd 6:0:0:0: [sda] permanent stream count = 5
[   57.167035] sd 6:0:0:0: [sda] Preferred minimum I/O size 512 bytes
[   57.168848] sd 6:0:0:0: [sda] Optimal transfer size 524288 bytes
[   57.191432] sd 6:0:0:0: [sda] Attached SCSI disk
[   57.198754] loop0: detected capacity change from 0 to 22528
[   57.208345] loop0: detected capacity change from 0 to 20480
[   57.217074] loop0: detected capacity change from 0 to 6144
[   57.228506] loop0: detected capacity change from 0 to 6144
[   57.253680] sd 6:0:0:0: [sda] Synchronizing SCSI cache
[   57.314886] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1)
[   57.317233] scsi host6: scsi_debug: version 0191 [20210520]
[   57.317233]   dev_size_mb=11, opts=0x0, submit_queues=1, statistics=0
[   57.320386] scsi 6:0:0:0: Direct-Access     Linux    scsi_debug       0191 PQ: 0 ANSI: 7
[   57.322475] scsi 6:0:0:0: Power-on or device reset occurred
[   57.329091] sd 6:0:0:0: [sda] 22528 512-byte logical blocks: (11.5 MB/11.0 MiB)
[   57.334890] sd 6:0:0:0: [sda] Write Protect is off
[   57.340104] sd 6:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
[   57.351712] sd 6:0:0:0: [sda] permanent stream count = 5
[   57.358249] sd 6:0:0:0: [sda] Preferred minimum I/O size 512 bytes
[   57.362251] sd 6:0:0:0: [sda] Optimal transfer size 524288 bytes
[   57.387495] sd 6:0:0:0: [sda] Attached SCSI disk
[   57.400797] loop0: detected capacity change from 0 to 22528
[   57.406708] loop0: detected capacity change from 0 to 22528
[   57.623719] sd 6:0:0:0: [sda] Synchronizing SCSI cache
[   59.018937] BTRFS: device fsid 376ab5c9-e431-4a37-95cb-19d29073069b devid 1 transid 8 /dev/loop0 (7:0) scanned by mount (26551)
[   59.022187] BTRFS info (device loop0): first mount of filesystem 376ab5c9-e431-4a37-95cb-19d29073069b
[   59.024572] BTRFS info (device loop0): using crc32c (crc32c-lib) checksum algorithm
[   59.028416] BTRFS info (device loop0): checking UUID tree
[   59.030189] BTRFS info (device loop0): turning on async discard
[   59.031858] BTRFS info (device loop0): enabling free space tree
[   59.058238] BTRFS info (device loop0): last unmount of filesystem 376ab5c9-e431-4a37-95cb-19d29073069b
[   59.963645] BTRFS: device fsid a3411a18-67ce-40d9-b051-556c5ace104d devid 1 transid 8 /dev/loop0 (7:0) scanned by mount (27805)
[   59.972390] BTRFS info (device loop0): first mount of filesystem a3411a18-67ce-40d9-b051-556c5ace104d
[   59.979033] BTRFS info (device loop0): using crc32c (crc32c-lib) checksum algorithm
[   59.986281] BTRFS info (device loop0): checking UUID tree
[   59.990164] BTRFS info (device loop0): turning on async discard
[   59.994528] BTRFS info (device loop0): enabling free space tree
[   60.027417] BTRFS info (device loop0): last unmount of filesystem a3411a18-67ce-40d9-b051-556c5ace104d
[   61.124009] UDPLite: UDP-Lite is deprecated and scheduled to be removed in 2025, please contact the netdev mailing list
[   61.281836] UDPLite6: UDP-Lite is deprecated and scheduled to be removed in 2025, please contact the netdev mailing list
[   61.673381] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem
[   61.676189] EXT4-fs (loop0): mounted filesystem a0510fd6-cb0e-4a92-a3e8-7b9060d6d979 r/w without journal. Quota mode: disabled.
[   61.686518] EXT4-fs (loop0): unmounting filesystem a0510fd6-cb0e-4a92-a3e8-7b9060d6d979.
[   61.695683] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem
[   61.700478] EXT4-fs (loop0): mounted filesystem a0510fd6-cb0e-4a92-a3e8-7b9060d6d979 r/w without journal. Quota mode: disabled.
[   61.716481] EXT4-fs (loop0): unmounting filesystem a0510fd6-cb0e-4a92-a3e8-7b9060d6d979.
[   64.145562] set_capacity_and_notify: 14 callbacks suppressed
[   64.145565] loop0: detected capacity change from 0 to 10240
[   64.161911] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem
[   64.164412] EXT4-fs (loop0): mounted filesystem a3e4cd52-eb93-4d63-a074-7dcc87b179f0 r/w without journal. Quota mode: disabled.
[   64.180216] EXT4-fs (loop0): re-mounted a3e4cd52-eb93-4d63-a074-7dcc87b179f0 ro.
[   64.189166] EXT4-fs (loop0): re-mounted a3e4cd52-eb93-4d63-a074-7dcc87b179f0 r/w.
[   64.204417] EXT4-fs (loop0): unmounting filesystem a3e4cd52-eb93-4d63-a074-7dcc87b179f0.
[   64.229174] loop0: detected capacity change from 0 to 10240
[   64.235842] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem
[   64.238119] EXT4-fs (loop0): mounted filesystem 47a07a6e-1f59-4a8b-a1b5-d05e21ef5fe7 r/w without journal. Quota mode: disabled.
[   64.243873] EXT4-fs (loop0): unmounting filesystem 47a07a6e-1f59-4a8b-a1b5-d05e21ef5fe7.
[   64.308995] loop0: detected capacity change from 0 to 10240
[   64.317941] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem
[   64.320719] EXT4-fs (loop0): mounted filesystem 2ba7282e-7ee7-471b-b437-4eb85615323e r/w without journal. Quota mode: disabled.
[   64.329491] EXT4-fs (loop0): unmounting filesystem 2ba7282e-7ee7-471b-b437-4eb85615323e.
[   64.343147] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem
[   64.348475] EXT4-fs (loop0): mounted filesystem 2ba7282e-7ee7-471b-b437-4eb85615323e r/w without journal. Quota mode: disabled.
[   64.358005] EXT4-fs (loop0): unmounting filesystem 2ba7282e-7ee7-471b-b437-4eb85615323e.
[   64.370953] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem
[   64.373445] EXT4-fs (loop0): mounted filesystem 2ba7282e-7ee7-471b-b437-4eb85615323e r/w without journal. Quota mode: disabled.
[   64.382961] EXT4-fs (loop0): re-mounted 2ba7282e-7ee7-471b-b437-4eb85615323e ro.
[   64.390483] EXT4-fs (loop0): unmounting filesystem 2ba7282e-7ee7-471b-b437-4eb85615323e.
[   64.446330] loop0: detected capacity change from 0 to 10240
[   64.459480] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem
[   64.464430] EXT4-fs (loop0): mounted filesystem 8cfa8ae4-1ba6-4f37-a68d-213aa898197c r/w without journal. Quota mode: disabled.
[   64.474173] EXT4-fs (loop0): unmounting filesystem 8cfa8ae4-1ba6-4f37-a68d-213aa898197c.
[   64.490146] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem
[   64.495202] EXT4-fs (loop0): mounted filesystem 8cfa8ae4-1ba6-4f37-a68d-213aa898197c r/w without journal. Quota mode: disabled.
[   64.504183] EXT4-fs (loop0): unmounting filesystem 8cfa8ae4-1ba6-4f37-a68d-213aa898197c.
[   64.519122] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem
[   64.523705] EXT4-fs (loop0): mounted filesystem 8cfa8ae4-1ba6-4f37-a68d-213aa898197c r/w without journal. Quota mode: disabled.
[   64.538669] EXT4-fs (loop0): unmounting filesystem 8cfa8ae4-1ba6-4f37-a68d-213aa898197c.
[   64.554353] EXT4-fs (loop0): couldn't mount as ext3 due to feature incompatibilities
[   64.559004] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem
[   64.563942] EXT4-fs (loop0): mounted filesystem 8cfa8ae4-1ba6-4f37-a68d-213aa898197c r/w without journal. Quota mode: disabled.
[   64.574823] EXT4-fs (loop0): unmounting filesystem 8cfa8ae4-1ba6-4f37-a68d-213aa898197c.
[   64.592822] EXT4-fs (loop0): couldn't mount as ext3 due to feature incompatibilities
[   64.598781] FAT-fs (loop0): bogus number of reserved sectors
[   64.602795] FAT-fs (loop0): Can't find a valid FAT filesystem
[   64.606763] FAT-fs (loop0): bogus number of reserved sectors
[   64.610561] FAT-fs (loop0): Can't find a valid FAT filesystem
[   64.616573] ISOFS: Unable to identify CD-ROM format.
[   64.686602] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1)
[   64.692541] scsi host6: scsi_debug: version 0191 [20210520]
[   64.692541]   dev_size_mb=50, opts=0x0, submit_queues=1, statistics=0
[   64.700591] scsi 6:0:0:0: Direct-Access     Linux    scsi_debug       0191 PQ: 0 ANSI: 7
[   64.706093] scsi 6:0:0:0: Power-on or device reset occurred
[   64.715218] sd 6:0:0:0: [sda] 102400 512-byte logical blocks: (52.4 MB/50.0 MiB)
[   64.721648] sd 6:0:0:0: [sda] Write Protect is off
[   64.727223] sd 6:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
[   64.739659] sd 6:0:0:0: [sda] permanent stream count = 5
[   64.746616] sd 6:0:0:0: [sda] Preferred minimum I/O size 512 bytes
[   64.751148] sd 6:0:0:0: [sda] Optimal transfer size 524288 bytes
[   64.776422] sd 6:0:0:0: [sda] Attached SCSI disk
[   64.936896]  sda: sda1 sda2 sda3 sda4
[   65.532469] EXT4-fs (sda1): mounting ext2 file system using the ext4 subsystem
[   65.537599] EXT4-fs (sda1): mounted filesystem 6d72da94-ae71-46ac-bd29-31aefc2ac763 r/w without journal. Quota mode: disabled.
[   65.541620] EXT4-fs (sda2): mounting ext2 file system using the ext4 subsystem
[   65.546615] EXT4-fs (sda2): mounted filesystem e52658a9-03ef-405e-beb0-ddd9bbfb0704 r/w without journal. Quota mode: disabled.
[   65.550659] EXT4-fs (sda3): mounting ext2 file system using the ext4 subsystem
[   65.554656] EXT4-fs (sda3): mounted filesystem 3df47241-f599-481e-b0c0-95de02950cf9 ro without journal. Quota mode: disabled.
[   65.595411] EXT4-fs (sda4): mounted filesystem 418dde7b-b7bf-42f1-b14d-2b6741b38c48 r/w with ordered data mode. Quota mode: disabled.
[   65.651382] EXT4-fs (sda1): unmounting filesystem 6d72da94-ae71-46ac-bd29-31aefc2ac763.
[   65.704766] EXT4-fs (sda2): unmounting filesystem e52658a9-03ef-405e-beb0-ddd9bbfb0704.
[   65.707998] EXT4-fs (sda3): unmounting filesystem 3df47241-f599-481e-b0c0-95de02950cf9.
[   65.760288] EXT4-fs (sda4): unmounting filesystem 418dde7b-b7bf-42f1-b14d-2b6741b38c48.
[   65.811077] EXT4-fs (sda4): mounted filesystem 418dde7b-b7bf-42f1-b14d-2b6741b38c48 r/w with ordered data mode. Quota mode: disabled.
[   65.866571] EXT4-fs (sda4): unmounting filesystem 418dde7b-b7bf-42f1-b14d-2b6741b38c48.
[   65.885448] EXT4-fs (sda1): mounting ext2 file system using the ext4 subsystem
[   65.893123] EXT4-fs (sda1): mounted filesystem 6d72da94-ae71-46ac-bd29-31aefc2ac763 r/w without journal. Quota mode: disabled.
[   65.900082] EXT4-fs (sda2): mounting ext2 file system using the ext4 subsystem
[   65.907319] EXT4-fs (sda2): mounted filesystem e52658a9-03ef-405e-beb0-ddd9bbfb0704 r/w without journal. Quota mode: disabled.
[   65.915174] EXT4-fs (sda3): mounting ext2 file system using the ext4 subsystem
[   65.921055] EXT4-fs (sda3): mounted filesystem 3df47241-f599-481e-b0c0-95de02950cf9 ro without journal. Quota mode: disabled.
[   65.979996] EXT4-fs (sda1): unmounting filesystem 6d72da94-ae71-46ac-bd29-31aefc2ac763.
[   66.036744] EXT4-fs (sda2): unmounting filesystem e52658a9-03ef-405e-beb0-ddd9bbfb0704.
[   66.043520] EXT4-fs (sda3): unmounting filesystem 3df47241-f599-481e-b0c0-95de02950cf9.
[   66.061272] EXT4-fs (sda3): mounting ext2 file system using the ext4 subsystem
[   66.069022] EXT4-fs (sda3): mounted filesystem 3df47241-f599-481e-b0c0-95de02950cf9 ro without journal. Quota mode: disabled.
[   66.080077] EXT4-fs (sda3): unmounting filesystem 3df47241-f599-481e-b0c0-95de02950cf9.
[   66.097046] EXT4-fs (sda1): mounting ext2 file system using the ext4 subsystem
[   66.103951] EXT4-fs (sda1): mounted filesystem 6d72da94-ae71-46ac-bd29-31aefc2ac763 ro without journal. Quota mode: disabled.
[   66.112446] EXT4-fs (sda2): mounting ext2 file system using the ext4 subsystem
[   66.119389] EXT4-fs (sda2): mounted filesystem e52658a9-03ef-405e-beb0-ddd9bbfb0704 ro without journal. Quota mode: disabled.
[   66.127859] EXT4-fs (sda3): mounting ext2 file system using the ext4 subsystem
[   66.134821] EXT4-fs (sda3): mounted filesystem 3df47241-f599-481e-b0c0-95de02950cf9 ro without journal. Quota mode: disabled.
[   66.179543] EXT4-fs (sda4): orphan cleanup on readonly fs
[   66.182890] EXT4-fs (sda4): mounted filesystem 418dde7b-b7bf-42f1-b14d-2b6741b38c48 ro with ordered data mode. Quota mode: disabled.
[   66.193417] EXT4-fs (sda1): unmounting filesystem 6d72da94-ae71-46ac-bd29-31aefc2ac763.
[   66.198526] EXT4-fs (sda2): unmounting filesystem e52658a9-03ef-405e-beb0-ddd9bbfb0704.
[   66.203504] EXT4-fs (sda3): unmounting filesystem 3df47241-f599-481e-b0c0-95de02950cf9.
[   66.208398] EXT4-fs (sda4): unmounting filesystem 418dde7b-b7bf-42f1-b14d-2b6741b38c48.
[   66.225487] EXT4-fs (sda1): mounting ext2 file system using the ext4 subsystem
[   66.234019] EXT4-fs (sda1): mounted filesystem 6d72da94-ae71-46ac-bd29-31aefc2ac763 r/w without journal. Quota mode: disabled.
[   66.243324] EXT4-fs (sda2): mounting ext2 file system using the ext4 subsystem
[   66.251823] EXT4-fs (sda2): mounted filesystem e52658a9-03ef-405e-beb0-ddd9bbfb0704 r/w without journal. Quota mode: disabled.
[   66.261200] EXT4-fs (sda3): mounting ext2 file system using the ext4 subsystem
[   66.268670] EXT4-fs (sda3): mounted filesystem 3df47241-f599-481e-b0c0-95de02950cf9 ro without journal. Quota mode: disabled.
[   66.315165] EXT4-fs (sda4): mounted filesystem 418dde7b-b7bf-42f1-b14d-2b6741b38c48 r/w with ordered data mode. Quota mode: disabled.
[   66.377423] EXT4-fs (sda1): unmounting filesystem 6d72da94-ae71-46ac-bd29-31aefc2ac763.
[   66.434718] EXT4-fs (sda2): unmounting filesystem e52658a9-03ef-405e-beb0-ddd9bbfb0704.
[   66.441790] EXT4-fs (sda3): unmounting filesystem 3df47241-f599-481e-b0c0-95de02950cf9.
[   66.497780] EXT4-fs (sda4): unmounting filesystem 418dde7b-b7bf-42f1-b14d-2b6741b38c48.
[   66.519039] EXT4-fs (sda1): mounting ext2 file system using the ext4 subsystem
[   66.527142] EXT4-fs (sda1): mounted filesystem 6d72da94-ae71-46ac-bd29-31aefc2ac763 r/w without journal. Quota mode: disabled.
[   66.535974] EXT4-fs (sda2): mounting ext2 file system using the ext4 subsystem
[   66.544217] EXT4-fs (sda2): mounted filesystem e52658a9-03ef-405e-beb0-ddd9bbfb0704 r/w without journal. Quota mode: disabled.
[   66.553018] EXT4-fs (sda3): mounting ext2 file system using the ext4 subsystem
[   66.561446] EXT4-fs (sda3): mounted filesystem 3df47241-f599-481e-b0c0-95de02950cf9 r/w without journal. Quota mode: disabled.
[   66.609222] EXT4-fs (sda4): mounted filesystem 418dde7b-b7bf-42f1-b14d-2b6741b38c48 r/w with ordered data mode. Quota mode: disabled.
[   66.670781] EXT4-fs (sda1): unmounting filesystem 6d72da94-ae71-46ac-bd29-31aefc2ac763.
[   66.727958] EXT4-fs (sda2): unmounting filesystem e52658a9-03ef-405e-beb0-ddd9bbfb0704.
[   66.785072] EXT4-fs (sda3): unmounting filesystem 3df47241-f599-481e-b0c0-95de02950cf9.
[   66.842132] EXT4-fs (sda4): unmounting filesystem 418dde7b-b7bf-42f1-b14d-2b6741b38c48.
[   66.861525] sd 6:0:0:0: [sda] Synchronizing SCSI cache
[   67.115962] loop0: detected capacity change from 0 to 102400
[   67.145779] loop1: detected capacity change from 0 to 102400
[   67.152167] BTRFS: device fsid e6418048-1b37-49d3-87bc-34f8fc793721 devid 1 transid 8 /dev/loop1 (7:1) scanned by mount (2055)
[   67.159743] BTRFS info (device loop1): first mount of filesystem e6418048-1b37-49d3-87bc-34f8fc793721
[   67.165691] BTRFS info (device loop1): using crc32c (crc32c-lib) checksum algorithm
[   67.172867] BTRFS info (device loop1): checking UUID tree
[   67.176350] BTRFS info (device loop1): turning on async discard
[   67.179482] BTRFS info (device loop1): enabling free space tree
[   67.190600] BTRFS info (device loop1): setting incompat feature flag for DEFAULT_SUBVOL (0x2)
[   67.202553] BTRFS info (device loop1): last unmount of filesystem e6418048-1b37-49d3-87bc-34f8fc793721
[   67.217965] BTRFS: device fsid e6418048-1b37-49d3-87bc-34f8fc793721 devid 1 transid 9 /dev/loop0 (7:0) scanned by mount (2096)
[   67.225528] BTRFS info (device loop0): first mount of filesystem e6418048-1b37-49d3-87bc-34f8fc793721
[   67.231506] BTRFS info (device loop0): using crc32c (crc32c-lib) checksum algorithm
[   67.237752] BTRFS info (device loop0): turning on async discard
[   67.241591] BTRFS info (device loop0): enabling free space tree
[   67.253014] BTRFS info (device loop0): last unmount of filesystem e6418048-1b37-49d3-87bc-34f8fc793721
[   67.282871] BTRFS: device fsid e6418048-1b37-49d3-87bc-34f8fc793721 devid 1 transid 9 /dev/loop0 (7:0) scanned by mount (2138)
[   67.290424] BTRFS info (device loop0): first mount of filesystem e6418048-1b37-49d3-87bc-34f8fc793721
[   67.296418] BTRFS info (device loop0): using crc32c (crc32c-lib) checksum algorithm
[   67.302718] BTRFS info (device loop0): turning on async discard
[   67.306615] BTRFS info (device loop0): enabling free space tree
[   67.317997] BTRFS info (device loop0): last unmount of filesystem e6418048-1b37-49d3-87bc-34f8fc793721
[   67.389001] loop0: detected capacity change from 0 to 10240
[   67.410879] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem
[   67.416543] EXT4-fs (loop0): mounted filesystem 4b483d3f-a06f-49ae-8e95-4bbd966b216b r/w without journal. Quota mode: disabled.
[   67.428176] EXT4-fs (loop0): unmounting filesystem 4b483d3f-a06f-49ae-8e95-4bbd966b216b.
[   67.446275] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem
[   67.451656] EXT4-fs (loop0): mounted filesystem 4b483d3f-a06f-49ae-8e95-4bbd966b216b r/w without journal. Quota mode: disabled.
[   67.461724] EXT4-fs (loop0): unmounting filesystem 4b483d3f-a06f-49ae-8e95-4bbd966b216b.
[   67.521619] loop0: detected capacity change from 0 to 10240
[   67.539495] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem
[   67.542053] EXT4-fs (loop0): mounted filesystem 52149de6-1732-4dad-8d89-4967b62cf982 r/w without journal. Quota mode: disabled.
[   67.547879] EXT4-fs (loop0): unmounting filesystem 52149de6-1732-4dad-8d89-4967b62cf982.
[   67.606722] loop0: detected capacity change from 0 to 10240
[   67.629215] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem
[   67.635562] EXT4-fs (loop0): mounted filesystem ff81f7f9-979b-4e22-a4ba-bbde6c670b78 r/w without journal. Quota mode: disabled.
[   67.647764] EXT4-fs (loop0): unmounting filesystem ff81f7f9-979b-4e22-a4ba-bbde6c670b78.
[   67.710069] loop0: detected capacity change from 0 to 10240
[   67.780191] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem
[   67.806198] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem
[   67.831276] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem
[   67.957868] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem
[   67.981523] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem
[   68.114562] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem
[   68.136778] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem
[   68.204227] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem
[   68.326418] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem
[   68.446670] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem
[   68.471034] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem
[   68.496320] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem
[   68.614551] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem
[   68.637925] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem
[   68.773690] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem
[   68.798347] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem
[   68.908638] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem
[   68.930678] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem
[   69.065223] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem
[   69.105885] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem
[   69.110828] EXT4-fs (loop0): re-mounted 984ce763-7c63-4339-a671-564bb408b40e ro.
[   69.149508] set_capacity_and_notify: 10 callbacks suppressed
[   69.149511] loop0: detected capacity change from 0 to 10240
[   69.160513] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem
[   69.166153] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem
[   69.172279] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem
[   69.178258] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem
[   69.184812] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem
[   69.191575] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem
[   69.288098] loop0: detected capacity change from 0 to 10240
[   69.300780] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem
[   69.317076] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem
[   69.466684] loop0: detected capacity change from 0 to 10240
[   69.478669] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem
[   69.501239] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem
[   69.572519] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1)
[   69.577200] scsi host6: scsi_debug: version 0191 [20210520]
[   69.577200]   dev_size_mb=50, opts=0x0, submit_queues=1, statistics=0
[   69.583653] scsi 6:0:0:0: Direct-Access     Linux    scsi_debug       0191 PQ: 0 ANSI: 7
[   69.588122] scsi 6:0:0:0: Power-on or device reset occurred
[   69.597690] sd 6:0:0:0: [sda] 102400 512-byte logical blocks: (52.4 MB/50.0 MiB)
[   69.602597] sd 6:0:0:0: [sda] Write Protect is off
[   69.607181] sd 6:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
[   69.617865] sd 6:0:0:0: [sda] permanent stream count = 5
[   69.623726] sd 6:0:0:0: [sda] Preferred minimum I/O size 512 bytes
[   69.627065] sd 6:0:0:0: [sda] Optimal transfer size 524288 bytes
[   69.651440] sd 6:0:0:0: [sda] Attached SCSI disk
[   69.803911]  sda: sda1 sda2 sda3 sda4
[   70.383399] EXT4-fs (sda1): mounting ext2 file system using the ext4 subsystem
[   70.483394] EXT4-fs (sda1): mounting ext2 file system using the ext4 subsystem
[   70.584257] EXT4-fs (sda1): mounting ext2 file system using the ext4 subsystem
[   70.624559] EXT4-fs (sda2): mounting ext2 file system using the ext4 subsystem
[   70.645520] EXT4-fs (sda3): mounting ext2 file system using the ext4 subsystem
[   70.666301] EXT4-fs (sda4): mounting ext2 file system using the ext4 subsystem
[   70.902599] sd 6:0:0:0: [sda] Synchronizing SCSI cache
[   71.024226] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1)
[   71.026774] scsi host6: scsi_debug: version 0191 [20210520]
[   71.026774]   dev_size_mb=50, opts=0x0, submit_queues=1, statistics=0
[   71.030236] scsi 6:0:0:0: Direct-Access     Linux    scsi_debug       0191 PQ: 0 ANSI: 7
[   71.032590] scsi 6:0:0:0: Power-on or device reset occurred
[   71.039486] sd 6:0:0:0: [sda] 102400 512-byte logical blocks: (52.4 MB/50.0 MiB)
[   71.045376] sd 6:0:0:0: [sda] Write Protect is off
[   71.050536] sd 6:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
[   71.062098] sd 6:0:0:0: [sda] permanent stream count = 5
[   71.068579] sd 6:0:0:0: [sda] Preferred minimum I/O size 512 bytes
[   71.072538] sd 6:0:0:0: [sda] Optimal transfer size 524288 bytes
[   71.097467] sd 6:0:0:0: [sda] Attached SCSI disk
[   71.251888]  sda: sda1 sda2 sda3 sda4
[   71.830417] EXT4-fs (sda1): mounting ext2 file system using the ext4 subsystem
[   71.853805] EXT4-fs (sda2): mounting ext2 file system using the ext4 subsystem
[   71.879228] EXT4-fs (sda3): mounting ext2 file system using the ext4 subsystem
[   71.898120] EXT4-fs (sda4): mounting ext2 file system using the ext4 subsystem
[   72.136653] sd 6:0:0:0: [sda] Synchronizing SCSI cache
[   72.251613] loop0: detected capacity change from 0 to 10240
[   72.290806] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem
[   72.312693] EXT4-fs (loop0): mounting ext2 file system using the ext4 subsystem
[   72.592957] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1)
[   72.596978] scsi host6: scsi_debug: version 0191 [20210520]
[   72.596978]   dev_size_mb=50, opts=0x0, submit_queues=1, statistics=0
[   72.600399] scsi 6:0:0:0: Direct-Access     Linux    scsi_debug       0191 PQ: 0 ANSI: 7
[   72.602646] scsi 6:0:0:0: Power-on or device reset occurred
[   72.609226] sd 6:0:0:0: [sda] 102400 512-byte logical blocks: (52.4 MB/50.0 MiB)
[   72.612440] sd 6:0:0:0: [sda] Write Protect is off
[   72.615901] sd 6:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
[   72.624440] sd 6:0:0:0: [sda] permanent stream count = 5
[   72.630618] sd 6:0:0:0: [sda] Preferred minimum I/O size 512 bytes
[   72.633904] sd 6:0:0:0: [sda] Optimal transfer size 524288 bytes
[   72.662494] sd 6:0:0:0: [sda] Attached SCSI disk
[   73.051772]  sda: sda1 sda2 sda3
[   73.226638] sd 6:0:0:0: [sda] Synchronizing SCSI cache
[   98.306616] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1)
[   98.309396] scsi host6: scsi_debug: version 0191 [20210520]
[   98.309396]   dev_size_mb=50, opts=0x0, submit_queues=1, statistics=0
[   98.312888] scsi 6:0:0:0: Direct-Access     Linux    scsi_debug       0191 PQ: 0 ANSI: 7
[   98.315249] scsi 6:0:0:0: Power-on or device reset occurred
[   98.321999] sd 6:0:0:0: [sda] 102400 512-byte logical blocks: (52.4 MB/50.0 MiB)
[   98.325821] sd 6:0:0:0: [sda] 4096-byte physical blocks
[   98.329555] sd 6:0:0:0: [sda] Write Protect is off
[   98.334146] sd 6:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
[   98.344665] sd 6:0:0:0: [sda] permanent stream count = 5
[   98.350548] sd 6:0:0:0: [sda] Preferred minimum I/O size 4096 bytes
[   98.353827] sd 6:0:0:0: [sda] Optimal transfer size 524288 bytes
[   98.378460] sd 6:0:0:0: [sda] Attached SCSI disk
[   98.777783]  sda: sda1 sda2 sda3 sda4 < sda5 sda6 >
[   99.142219]  sda: sda1 sda2 sda3 sda4 < sda5 sda6 >
[   99.900676]  sda: sda1 sda2 sda3
[  100.624680]  sda: sda1
[  101.430977]  sda: sda1 sda2 sda3 sda4 < sda5 sda6 >
[  102.260694]  sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 >
[  102.985562]  sda: sda1
[  103.334819]  sda: sda1
[  104.064700]  sda: sda1 sda2 < >
[  104.414701]  sda: sda1 sda2 < >
[  105.144648]  sda: sda1 sda2 < >
[  105.494774]  sda: sda1 sda2 < >
[  106.270773]  sda: sda1 sda2 sda3 sda4 < sda5 sda6 >
[  106.623868]  sda: sda1 sda2 sda3 sda4 < sda5 sda6 >
[  107.397817]  sda: sda1 sda2 sda3 sda4 < sda5 sda6 >
[  107.752148]  sda: sda1 sda2 sda3 sda4 < sda5 sda6 >
[  108.485657]  sda: sda1
[  109.231618]  sda: sda1 sda3
[  109.980786]  sda: sda1 sda2
[  110.773946]  sda: sda1 sda2 sda3 sda4
[  111.515640]  sda: sda1 sda2 sda3
[  111.597631] sd 6:0:0:0: [sda] Synchronizing SCSI cache
[  111.664979] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1)
[  111.667652] scsi host6: scsi_debug: version 0191 [20210520]
[  111.667652]   dev_size_mb=100, opts=0x0, submit_queues=1, statistics=0
[  111.671235] scsi 6:0:0:0: Direct-Access     Linux    scsi_debug       0191 PQ: 0 ANSI: 7
[  111.673648] scsi 6:0:0:0: Power-on or device reset occurred
[  111.680582] sd 6:0:0:0: [sda] 204800 512-byte logical blocks: (105 MB/100 MiB)
[  111.685502] sd 6:0:0:0: [sda] 4096-byte physical blocks
[  111.690152] sd 6:0:0:0: [sda] Write Protect is off
[  111.695386] sd 6:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
[  111.707007] sd 6:0:0:0: [sda] permanent stream count = 5
[  111.713518] sd 6:0:0:0: [sda] Preferred minimum I/O size 4096 bytes
[  111.718120] sd 6:0:0:0: [sda] Optimal transfer size 524288 bytes
[  111.743474] sd 6:0:0:0: [sda] Attached SCSI disk
[  112.421221]  sda: sda1 sda2 sda3 sda4
[  113.547911]  sda: sda1 sda2 sda3 sda4
[  114.700233]  sda: sda1 sda2 sda3 sda4
[  114.731623] sd 6:0:0:0: [sda] Synchronizing SCSI cache
[  114.799395] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1)
[  114.801824] scsi host6: scsi_debug: version 0191 [20210520]
[  114.801824]   dev_size_mb=50, opts=0x0, submit_queues=1, statistics=0
[  114.808589] scsi 6:0:0:0: Direct-Access     Linux    scsi_debug       0191 PQ: 0 ANSI: 7
[  114.812885] scsi 6:0:0:0: Power-on or device reset occurred
[  114.821031] sd 6:0:0:0: [sda] 102400 512-byte logical blocks: (52.4 MB/50.0 MiB)
[  114.825787] sd 6:0:0:0: [sda] 4096-byte physical blocks
[  114.830449] sd 6:0:0:0: [sda] Write Protect is off
[  114.835682] sd 6:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
[  114.847209] sd 6:0:0:0: [sda] permanent stream count = 5
[  114.853518] sd 6:0:0:0: [sda] Preferred minimum I/O size 4096 bytes
[  114.856762] sd 6:0:0:0: [sda] Optimal transfer size 524288 bytes
[  114.881526] sd 6:0:0:0: [sda] Attached SCSI disk
[  115.563447]  sda: sda1 sda2 sda3 sda4 sda5
[  116.088380]  sda: sda1 sda2 sda3 sda4 sda5
[  116.602390]  sda: sda1 sda2 sda3 sda4 sda5
[  117.116145]  sda: sda1 sda2 sda3 sda4 sda5
[  117.630348]  sda: sda1 sda2 sda3 sda4 sda5
[  118.144165]  sda: sda1 sda2 sda3 sda4 sda5
[  118.695257]  sda: sda1 sda2 sda3 sda4 sda5
[  119.245984]  sda: sda1 sda2 sda3 sda4 sda5
[  119.788357]  sda: sda1 sda2 sda3 sda4 sda5
[  120.364151]  sda: sda1 sda2 sda3 sda4 sda5
[  120.930280]  sda: sda1 sda2 sda3 sda4 sda5
[  121.497493]  sda: sda1 sda2 sda3 sda4 sda5
[  122.741094]  sda: sda1 sda2 sda3 sda4
[  123.874717]  sda: sda1
[  124.385031]  sda: sda1
[  125.480219]  sda: sda1 sda2 sda3 sda4
[  125.994810]  sda: sda1 sda2 sda3 sda4
[  126.035625] sd 6:0:0:0: [sda] Synchronizing SCSI cache
[  126.126266] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1)
[  126.132867] scsi host6: scsi_debug: version 0191 [20210520]
[  126.132867]   dev_size_mb=100, opts=0x0, submit_queues=1, statistics=0
[  126.141706] scsi 6:0:0:0: Direct-Access     Linux    scsi_debug       0191 PQ: 0 ANSI: 7
[  126.147775] scsi 6:0:0:0: Power-on or device reset occurred
[  126.157009] sd 6:0:0:0: [sda] 204800 512-byte logical blocks: (105 MB/100 MiB)
[  126.161773] sd 6:0:0:0: [sda] Write Protect is off
[  126.166333] sd 6:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
[  126.177085] sd 6:0:0:0: [sda] permanent stream count = 5
[  126.182928] sd 6:0:0:0: [sda] Preferred minimum I/O size 512 bytes
[  126.186167] sd 6:0:0:0: [sda] Optimal transfer size 524288 bytes
[  126.210454] sd 6:0:0:0: [sda] Attached SCSI disk
[  126.541719]  sda: sda1
[  127.170562]  sda: sda1
[  127.712145]  sda: sda1
[  128.245427]  sda: sda1
[  128.355542] sd 6:0:0:0: [sda] Synchronizing SCSI cache
[  128.415386] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1)
[  128.419929] scsi host6: scsi_debug: version 0191 [20210520]
[  128.419929]   dev_size_mb=100, opts=0x0, submit_queues=1, statistics=0
[  128.426050] scsi 6:0:0:0: Direct-Access     Linux    scsi_debug       0191 PQ: 0 ANSI: 7
[  128.430216] scsi 6:0:0:0: Power-on or device reset occurred
[  128.438390] sd 6:0:0:0: [sda] 204800 512-byte logical blocks: (105 MB/100 MiB)
[  128.444207] sd 6:0:0:0: [sda] Write Protect is off
[  128.449501] sd 6:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
[  128.461063] sd 6:0:0:0: [sda] permanent stream count = 5
[  128.467531] sd 6:0:0:0: [sda] Preferred minimum I/O size 512 bytes
[  128.471472] sd 6:0:0:0: [sda] Optimal transfer size 524288 bytes
[  128.496476] sd 6:0:0:0: [sda] Attached SCSI disk
[  128.852782]  sda: sda1
[  129.210762]  sda: sda1
[  129.576685]  sda: sda1
[  129.942793]  sda: sda1
[  130.308793]  sda: sda1
[  130.673601]  sda: sda1
[  131.035786]  sda: sda1
[  131.402856]  sda: sda1
[  131.769802]  sda: sda1
[  132.135672]  sda: sda1
[  132.499806]  sda: sda1
[  132.862778]  sda: sda1
[  133.226830]  sda: sda1
[  133.616913]  sda: sda1 sda2
[  133.996914]  sda: sda1 sda2 sda3
[  134.352916]  sda: sda1 sda2 sda3
[  134.719881]  sda: sda1 sda2 sda3
[  135.718983]  sda: sda1
[  136.239071]  sda: sda1
[  136.770166]  sda: sda1
[  137.301275]  sda: sda1
[  137.833157]  sda: sda1
[  138.365081]  sda: sda1
[  138.895068]  sda: sda1
[  139.424052]  sda: sda1
[  139.954025]  sda: sda1
[  140.481448]  sda: sda1
[  141.010609]  sda: sda1
[  141.534836]  sda: sda1
[  142.060968]  sda: sda1
[  142.605098]  sda: sda1 sda2
[  143.147213]  sda: sda1 sda2 sda3
[  143.667277]  sda: sda1 sda2 sda3
[  144.196174]  sda: sda1 sda2 sda3
[  145.016917]  sda: sda1 sda2 sda3 < sda5 sda6 > sda4
[  145.377014]  sda: sda1 sda2 sda3 < sda5 sda6 > sda4
[  145.458618] sd 6:0:0:0: [sda] Synchronizing SCSI cache
[  145.536577] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1)
[  145.542603] scsi host6: scsi_debug: version 0191 [20210520]
[  145.542603]   dev_size_mb=50, opts=0x0, submit_queues=1, statistics=0
[  145.550603] scsi 6:0:0:0: Direct-Access     Linux    scsi_debug       0191 PQ: 0 ANSI: 7
[  145.556072] scsi 6:0:0:0: Power-on or device reset occurred
[  145.565066] sd 6:0:0:0: [sda] 102400 512-byte logical blocks: (52.4 MB/50.0 MiB)
[  145.567311] sd 6:0:0:0: [sda] 4096-byte physical blocks
[  145.569914] sd 6:0:0:0: [sda] Write Protect is off
[  145.573439] sd 6:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
[  145.582214] sd 6:0:0:0: [sda] permanent stream count = 5
[  145.586892] sd 6:0:0:0: [sda] Preferred minimum I/O size 4096 bytes
[  145.588785] sd 6:0:0:0: [sda] Optimal transfer size 524288 bytes
[  145.613504] sd 6:0:0:0: [sda] Attached SCSI disk
[  146.276229]  sda: sda1 sda2 sda3 sda4
[  147.381132]  sda: sda1 sda2 sda3 sda4
[  148.488084]  sda: sda1 sda2 sda3 sda4
[  149.228612] sd 6:0:0:0: [sda] Synchronizing SCSI cache
[  149.292847] scsi_debug:sdebug_driver_probe: scsi_debug: trim poll_queues to 0. poll_q/nr_hw = (0/1)
[  149.295703] scsi host6: scsi_debug: version 0191 [20210520]
[  149.295703]   dev_size_mb=50, opts=0x0, submit_queues=1, statistics=0
[  149.299519] scsi 6:0:0:0: Direct-Access     Linux    scsi_debug       0191 PQ: 0 ANSI: 7
[  149.302219] scsi 6:0:0:0: Power-on or device reset occurred
[  149.309227] sd 6:0:0:0: [sda] 102400 512-byte logical blocks: (52.4 MB/50.0 MiB)
[  149.313961] sd 6:0:0:0: [sda] 4096-byte physical blocks
[  149.318326] sd 6:0:0:0: [sda] Write Protect is off
[  149.323467] sd 6:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
[  149.334995] sd 6:0:0:0: [sda] permanent stream count = 5
[  149.341484] sd 6:0:0:0: [sda] Preferred minimum I/O size 4096 bytes
[  149.345505] sd 6:0:0:0: [sda] Optimal transfer size 524288 bytes
[  149.370513] sd 6:0:0:0: [sda] Attached SCSI disk
[  152.098124]  sda: sda1
[  153.254107]  sda: sda1
[  153.330649] sd 6:0:0:0: [sda] Synchronizing SCSI cache
[  153.521925] loop0: detected capacity change from 0 to 10240
[  153.535188] Adding 5116k swap on /dev/loop0.  Priority:-2 extents:1 across:5116k 
[  153.608026] loop0: detected capacity change from 0 to 10240
[  153.626190] Adding 5116k swap on /dev/loop0.  Priority:-2 extents:1 across:5116k 
[  153.699721] loop0: detected capacity change from 0 to 10240
[  153.718872] Adding 5116k swap on /dev/loop0.  Priority:-2 extents:1 across:5116k 
[  153.792042] loop0: detected capacity change from 0 to 10240
[  153.837640] Adding 5116k swap on /dev/loop0.  Priority:-2 extents:1 across:5116k 
[  153.924416] loop0: detected capacity change from 0 to 10240
[  153.973535] Adding 5116k swap on /dev/loop0.  Priority:-2 extents:1 across:5116k 
[  159.450129] udevd[13124]: starting version 3.2.14
[  159.455637] udevd[13125]: starting eudev-3.2.14
