# AMD KV260 with u-boot 2025.10rc2 based firmware
# safe to ignore minor firmware issue
zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: failed to set: pin
zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: set mux failed for pin
request failed for node
error -EACCES: failed to add to PM domain domain
probe with driver sdhci-arasan failed with error
Error applying setting, reverse things back
# safe to ignore initrd warning
Can't lookup blockdev
# X11 fails to start without connected display
modeset(0): failed to set mode: Invalid argument
# minor USB setup issue
device descriptor read/64, error

# Rockpi4b with u-boot 2025.10rc2 based firmware
memory-controller: probe with driver rk3399-dmc-freq failed with error
probe with driver rockchip-pcie failed with error
platform hdmi-sound: deferred probe pending: asoc-simple-card: parse error
deferred probe pending: rockchip-spi: Failed to request optional TX DMA channel
platform sound: deferred probe pending: asoc-audio-graph-card: parse error
platform sound-dit: deferred probe pending: asoc-audio-graph-card: parse error
# no GPU fan
Failed to register cooling device

# AMD zcu102 with u-boot 2025.10rc2 based firmware
# optee not available on all devices
optee firmware:optee: probe with driver optee failed with error
# SPI device probe error
spi_master spi0: Failed to create SPI device for
# PHY clock not correct
deferred probe pending: xilinx-psgtr: Failed to get ref clock

# TI k3 am62p5-sk with u-boot 2024.04-ti
# small issue in devicetree
OPP table can't be empty

# TI BeaglePlay
# firmware device setup error
Failed to create device link (0x180) with supplier 600000.gpio
# USB driver error messages but stack works
dwc3-usb: error -EINVAL: invalid resource
dwc3-usb: can't map PHY IOMEM resource. Won't apply i2409 fix.
# wl18xx firmware load error, not available from linux-firmware
wl18xx_driver wl18xx.6.auto: Direct firmware load for ti-connectivity/wl18xx-conf.bin failed
wlcore: ERROR could not get configuration binary ti-connectivity/wl18xx-conf.bin
# Audio SOC driver error messages
davinci-mcasp 2b10000.audio-controller: ASoC error (-22): at snd_soc_dai_hw_params
davinci-mcasp.0-i2s-hifi: ASoC error (-22): at __soc_pcm_hw_params() on davinci-mcasp.0-i2s-hifi

# NXP imx8mp verdin with u-boot 2025.10rc2
# RTC detection issue
oscillator failed, set time!
# uart issue
serial: failed to get ipg clk
# GPIO driver/dt issue
failed writing register: -6
# Audio codec issue
nau8822 3-001a: Failed to issue reset
# Audio devicetree issue
platform sound: deferred probe pending: asoc-simple-card: parse error

# Broadcom Rpi4 with u-boot 2025.10rc2
# wifi firmware issue
Direct firmware load for brcm/brcmfmac43455-sdio.raspberrypi,4-model-b.bin failed

# Qualcomm rb3gen2 with u-boot 2025.10rc2 based firmware
# PMIC issue
qcom_pmic_glink pmic-glink: Failed to create device link
# i2c issue
geni_i2c 980000.i2c: error -ENXIO: Invalid proto
geni_i2c 984000.i2c: error -ENXIO: Invalid proto
# wifi issues
ath11k 17a10040.wifi: failed to get rproc:
# drm issue
auxiliary aux_bridge.aux_bridge.0: deferred probe pending: aux_bridge.aux_bridge: failed to acquire drm_bridge
auxiliary pmic_glink.altmode.0: deferred probe pending: pmic_glink_altmode.pmic_glink_altmode: failed to acquire retimer-switch for port
